Table of Contents
Advertisement
Quick Links
Advertisement
Table of Contents
Related Manuals for Trotec PAGS 10-230
Summary of Contents for Trotec PAGS 10-230
- Page 1 PAGS 10-230 OPERATING MANUAL ANGLE GRINDER...
-
Page 2: Table Of Contents
Notice Accessory suited for cutting operations This signal word indicates important information (e.g. This symbol indicates that the supplied accessory may material damage), but does not indicate hazards. be used for cutting. Operating manual – angle grinder PAGS 10-230... -
Page 3: Safety
Power tools create sparks which may ignite the dust reduce personal injuries. or fumes. • Keep children and bystanders away while operating a power tool. Distractions can cause you to lose control. Operating manual – angle grinder PAGS 10-230... - Page 4 Use of the power tool for operations different from those intended could result in a hazardous situation. Operating manual – angle grinder PAGS 10-230...
- Page 5 • Do not operate the power tool near flammable materials. Sparks could ignite these materials. • Do not use accessories that require liquid coolants. Using water or other liquid coolants may result in electrocution or shock. Operating manual – angle grinder PAGS 10-230...
- Page 6 Never attempt to remove the cut-off wheel from the cut while the wheel is in motion otherwise kickback may occur. Investigate and take corrective action to eliminate the cause of wheel binding. Operating manual – angle grinder PAGS 10-230...
- Page 7 If you notice damages, no longer use the device. Do not use the device when the device or your hands We recommend using the power tool with original Trotec are damp or wet! accessories. Warning of electrical voltage...
-
Page 8: Information About The Device
1. In an emergency, disconnect the device from the mains feed-in: Switch the device off and disconnect the power cable from the mains socket. Hold onto the mains plug while doing so. 2. Do not reconnect a defective device to the mains. Operating manual – angle grinder PAGS 10-230... -
Page 9: Scope Of Delivery
Uncertainty K 3 dB Rotatable handle On/off switch with start lock Venting slots Carbon brush cover Guard Additional handle Adjusting screw Coded projection Locking lever Mounting flange Cutting disc Clamping nut Pin-type face wrench Operating manual – angle grinder PAGS 10-230... -
Page 10: Transport And Storage
• Hold onto the mains plug while pulling the power cable out national regulations. of the mains socket. • Allow the device to cool down. • Remove the tool from the tool holder. Operating manual – angle grinder PAGS 10-230... - Page 11 To adjust the guard (8), please proceed as follows: 1. Open the locking lever (12). 2. Check the additional handle (9) for tight fit. 3. For disassembly unscrew the additional handle (9) counter- clockwise. Operating manual – angle grinder PAGS 10-230...
- Page 12 ü The spindle is at a standstill and the cutting disc is no longer rotating. 1. Press the spindle lock (1) to block the gears. 2. Slowly turn the clamping nut (15) to the locking point until the lock is fixed. Press and hold the spindle lock (1). Operating manual – angle grinder PAGS 10-230...
- Page 13 The flat side of the clamping nut must point to the device. 4. Remove the used cutting disc (14). Make sure that the mounting flange (13) is firmly locked in place in the designated recesses. 8. Press the spindle lock (1) to lock the gears. Operating manual – angle grinder PAGS 10-230...
-
Page 14: Operation
Otherwise, there is a risk of injury. Connecting the power cable 1. Insert the mains plug into a properly secured mains socket. Operating manual – angle grinder PAGS 10-230... - Page 15 • Remove the tool from the device (see Start-up chapter). The disc keeps running after the device has been • Clean the device according to the Maintenance chapter. switched off. • Store the device according to the Storage chapter. Risk of injury. Operating manual – angle grinder PAGS 10-230...
-
Page 16: Available Accessories
Troubleshooting tasks which require the housing to be opened • Reduce the pressure applied on the workpiece. must only be carried out by a specialist dealer or by Trotec. • Check whether the workpiece is suitable for the tasks to Slight smoke or odour are emitted during first use: be carried out. -
Page 17: Maintenance
• Remove dust from inside the guard (8), from the mounting flange (13) and from the clamping nut (15). • Keep the ventilation openings free from dust deposits to prevent overheating of the motor. • For maintenance of the cutting disc, see chapter Tool change. Operating manual – angle grinder PAGS 10-230... - Page 18 4. Hold the pressure spring (18) down and insert a new carbon brush (20) into the guide. 5. Connect the contact connector (17) with the pin. 3. Press the pressure spring (18) down and take the worn carbon brush (19) out of the guide. Operating manual – angle grinder PAGS 10-230...
-
Page 19: Disposal
7. Repeat this process on the other side of the device. Notice Before switching the device on, the contact connector must be connected; otherwise the device can be damaged. Operating manual – angle grinder PAGS 10-230... - Page 20 Trotec GmbH & Co. KG Grebbener Str. 7 D-52525 Heinsberg +49 2452 962-400 +49 2452 962-200 info@trotec.com www.trotec.com...