Table of Contents
Advertisement
Quick Links
Advertisement
Table of Contents
Related Manuals for Trotec PAGS 21-115
Summary of Contents for Trotec PAGS 21-115
- Page 1 PAGS 21-115 ORIGINAL INSTRUCTIONS CORDLESS ANGLE GRINDER...
-
Page 2: Table Of Contents
Info Accessory suited for cutting operations Information marked with this symbol helps you to carry This symbol indicates that the supplied accessory may out your tasks quickly and safely. be used for cutting. cordless angle grinder PAGS 21-115... -
Page 3: Safety
• Do not expose power tools to rain or wet conditions. safety principles. A careless action can cause severe Water entering a power tool will increase the risk of injury within a fraction of a second. electric shock. cordless angle grinder PAGS 21-115... - Page 4 • Use power tools only with specifically designed battery packs. Use of any other battery packs may create a risk of injury and fire. cordless angle grinder PAGS 21-115...
- Page 5 • Do not operate the power tool near flammable materials. Sparks could ignite these materials. • Do not use accessories that require liquid coolants. Using water or other liquid coolants may result in electrocution or shock. cordless angle grinder PAGS 21-115...
- Page 6 An the wheel. improperly mounted wheel that projects through the plane of the guard lip cannot be adequately protected. cordless angle grinder PAGS 21-115...
- Page 7 Loose and spinning an adequate dust extraction system must be provided. attachment strings can entangle your fingers or snag on the workpiece. We recommend using the power tool with original Trotec accessories. Safety Warnings Specific for Wire Brushing Foreseeable misuse Operations •...
- Page 8 There is a risk of a short-circuit due to liquids penetrating the housing! Do not immerse the device and the accessories in water. Make sure that no water or other liquids can enter the housing. cordless angle grinder PAGS 21-115...
- Page 9 Warning The tool holder must be firmly locked in place before switching the device on, for an insufficiently or incorrectly clamped accessory could be catapulted out of the tool holder uncontrollably upon switch-on. cordless angle grinder PAGS 21-115...
-
Page 10: Information About The Device
• 1 x Cutting disc for metal, cutting disc diameter: 115 mm • 1 x Guard • 1 x Additional handle • 1 x Face spanner • 1 x Clamping nut • 1 x Transport case • 1 x Manual cordless angle grinder PAGS 21-115... - Page 11 1.7 m/s² additional handle a h,co Uncertainty K main handle / 1.5 m/s² additional handle Sound values according to EN 62841 Sound pressure level L 81 dB (A) Sound power L 92 dB(A) Uncertainty K 3 dB cordless angle grinder PAGS 21-115...
-
Page 12: Transport And Storage
• Check the contents of the transport case for completeness and look for damages. Warning Risk of suffocation! Do not leave the packaging lying around. Children may use it as a dangerous toy. • Dispose of the packaging material according to the national regulations. cordless angle grinder PAGS 21-115... - Page 13 Allow the battery (12) to cool down to room temperature. 5. Take the battery (12) out of the quick charger (13) by pressing and holding the release button (19) and pulling the battery (12) off the quick charger (13). cordless angle grinder PAGS 21-115...
- Page 14 1. Screw the additional handle (14) clockwise into the thread (2) either on the right or left side or on top of the housing. 2. Check the additional handle (14) for tight fit. 3. For disassembly unscrew the additional handle (14) counter-clockwise. cordless angle grinder PAGS 21-115...
- Page 15 The closed side of the guard must always point You can increase the clamping force of the lock by to the user. tightening the adjusting screw (8). 3. Close the locking lever (10). cordless angle grinder PAGS 21-115...
- Page 16 3. Press the spindle lock (1) to block the gears. 4. Slowly turn the clamping nut (16) to the locking point until the lock is fixed. Press and hold the spindle lock (1). cordless angle grinder PAGS 21-115...
- Page 17 16. Put the battery back in. Caution If the disc is out-of-round, rotates unevenly, vibrates, oscillates, or if unusual noises or sparks are generated, the cutting disc must be exchanged immediately. Otherwise, there is a risk of injury. cordless angle grinder PAGS 21-115...
-
Page 18: Operation
• Do not slow down the decelerating cutting disc by pressing against the side of the disc. • Always move the cutting disc through the workpiece in reverse rotation. cordless angle grinder PAGS 21-115... - Page 19 • Remove the battery from the device (see Start-up chapter). • Remove the tool from the device (see Start-up chapter). • Clean the device according to the Maintenance chapter. • Store the device according to the Transport and storage chapter. cordless angle grinder PAGS 21-115...
-
Page 20: Available Accessories
• Make sure that the cutting disc is not jammed in the • Check the quick charger for damages. Should the quick workpiece. charger be damaged, stop using it. Contact the Trotec The motor slows down: customer service. • Check whether the device is overloaded by the workpiece. -
Page 21: Maintenance
Inside the device, there are no parts that need to be maintained or lubricated by the user. Safety signs on the battery and the charger Check the safety signs attached to the battery and the charger at regular intervals. Replace illegible safety signs! cordless angle grinder PAGS 21-115... -
Page 22: Disposal
The icon with the crossed-out waste bin on waste electrical or electronic equipment stipulates that this equipment We – Trotec GmbH – declare in sole responsibility that the must not be disposed of with the household waste at the end of product designated below was developed, constructed and its life. - Page 23 Trotec GmbH Grebbener Str. 7 D-52525 Heinsberg +49 2452 962-400 +49 2452 962-200 info@trotec.com www.trotec.com...