Information marked with this symbol indicates that wet This symbol indicates that the supplied accessory may grinding is prohibited. be used for cutting. Notice This signal word indicates important information (e.g. material damage), but does not indicate hazards. Operating manual – cordless angle grinder PAGS 20-115...
Loose clothes, jewellery or long hair can be such as pipes, radiators, ranges and refrigerators. caught in moving parts. There is an increased risk of electric shock if your body is earthed or grounded. Operating manual – cordless angle grinder PAGS 20-115...
Page 4
• Keep handles and gripping surfaces dry, clean and free from oil and grease. Slippery handles and gripping surfaces do not allow for safe handling and control of the tool in unexpected situations. Operating manual – cordless angle grinder PAGS 20-115...
Page 5
Damaged accessories will normally break apart during this test time. Operating manual – cordless angle grinder PAGS 20-115...
Page 6
An improperly mounted wheel that projects through the plane of the guard lip cannot be adequately protected. Operating manual – cordless angle grinder PAGS 20-115...
Page 7
• for cutting tiles and concrete blocks Warning of electrical voltage We recommend using the power tool with original Trotec Work on the electrical components must only be accessories. carried out by an authorised specialist company!
The tool holder must be firmly locked in place before switching the device on, for an insufficiently or incorrectly clamped accessory could be catapulted out of the tool holder uncontrollably upon switch-on. Operating manual – cordless angle grinder PAGS 20-115...
Page 9
• 1 x Cutting disc for metal, cutting disc diameter: 115 mm • 1 x Guard • 1 x Additional handle • 1 x Face spanner • 1 x Clamping nut • 1 x Transport case • 1 x Manual Operating manual – cordless angle grinder PAGS 20-115...
Page 10
1.7 m/s² handle a Uncertainty K main handle / 1.5 m/s² additional handle Sound values according to EN 60745 Sound pressure level L 81 dB(A) Sound power L 92 dB(A) Uncertainty K 3 dB Operating manual – cordless angle grinder PAGS 20-115...
• Remove the battery from the device. to the battery caused by a deep discharge. • Remove the tool from the tool holder. • Clean the device as described in the Maintenance chapter. Operating manual – cordless angle grinder PAGS 20-115...
Page 12
Allow the battery (12) to cool down to room temperature. 5. Remove the battery (12) from the quick charger (13). 2. If required, charge the battery (12) as described in the section Charging the battery. Operating manual – cordless angle grinder PAGS 20-115...
Page 13
1. Screw the additional handle (14) clockwise into the thread (2) either on the right or left side or on top of the housing. 2. Check the additional handle (14) for tight fit. 3. For disassembly unscrew the additional handle (14) counter-clockwise. Operating manual – cordless angle grinder PAGS 20-115...
Page 14
4. Check whether the guard (7) is properly locked in place. It must be impossible to rotate the guard. You can increase the clamping force of the lock by tightening the adjusting screw (8). Operating manual – cordless angle grinder PAGS 20-115...
Page 15
3. Press the spindle lock (1) to block the gears. 4. Slowly turn the clamping nut (16) to the locking point until the lock is fixed. Press and hold the spindle lock (1). Operating manual – cordless angle grinder PAGS 20-115...
Page 16
Caution If the disc is out-of-round, rotates unevenly, vibrates, oscillates, or if unusual noises or sparks are generated, the cutting disc must be exchanged immediately. Otherwise, there is a risk of injury. Operating manual – cordless angle grinder PAGS 20-115...
• Do not slow down the decelerating cutting disc by pressing against the side of the disc. • Always move the cutting disc through the workpiece in reverse rotation. Operating manual – cordless angle grinder PAGS 20-115...
• Store the device according to the Storage chapter. • Check the fuse (home). • Check the quick charger for damages. Should the quick charger be damaged, stop using it. Contact the Trotec customer service. • Check the battery terminals for dirt. Remove any dirt.
Page 19
• Check whether the chosen cutting disc is suitable for the material to be processed. • If the cutting disc is worn, replace it with a new one. Operating manual – cordless angle grinder PAGS 20-115...
• Keep the connecting terminals on the battery pack clean. • Keep the ventilation openings free from dust deposits to prevent overheating of the motor. • For maintenance of the cutting disc, see chapter Tool change. Operating manual – cordless angle grinder PAGS 20-115...
Page 22
Trotec GmbH & Co. KG Grebbener Str. 7 D-52525 Heinsberg +49 2452 962-400 +49 2452 962-200 info@trotec.com www.trotec.com...