Table of Contents
Advertisement
Quick Links
Advertisement
Table of Contents
Related Manuals for Trotec PAGS 10-115
Summary of Contents for Trotec PAGS 10-115
- Page 1 PAGS 10-115 OPERATING MANUAL ANGLE GRINDER...
-
Page 2: Table Of Contents
Note This signal word indicates important information (e.g. material damage), but does not indicate hazards. Info Information marked with this symbol helps you to carry out your tasks quickly and safely. Operating manual – angle grinder PAGS 10-115... -
Page 3: Safety
Power tools create sparks which may ignite the dust or fumes. • Keep children and bystanders away while operating a power tool. Distractions can cause you to lose control. Operating manual – angle grinder PAGS 10-115... - Page 4 • Keep handles and gripping surfaces dry, clean and free from oil and grease. Slippery handles and gripping surfaces do not allow for safe handling and control of the tool in unexpected situations. Operating manual – angle grinder PAGS 10-115...
- Page 5 Damaged accessories will normally break apart during this test time. Operating manual – angle grinder PAGS 10-115...
- Page 6 • Do not position your body in the area where power tool will move if kickback occurs. Kickback will propel the tool in direction opposite to the wheel’s movement at the point of snagging. Operating manual – angle grinder PAGS 10-115...
- Page 7 • If the use of a guard is recommended for wire brushing, do not allow any interference of the wire wheel or brush with the guard. Wire wheel or brush may expand in diameter due to work load and centrifugal forces. Operating manual – angle grinder PAGS 10-115...
- Page 8 If you notice damages, no longer use the device. Do not use the device when the device or your hands We recommend using the power tool with original Trotec accessories. are damp or wet!
- Page 9 2. In an emergency, disconnect the device from the mains feed-in: Hold onto the mains plug while pulling the power cable out of the mains socket. 3. Do not reconnect a defective device to the mains. Operating manual – angle grinder PAGS 10-115...
-
Page 10: Information About The Device
• 1 x Cutting disc for metal, cutting disc diameter: 115 mm • 1 x Guard • 1 x Additional handle • 1 x Pin-type face wrench • 1 x Clamping nut • 1 x Transport case • 1 x Manual Operating manual – angle grinder PAGS 10-115... - Page 11 1.5 m/s² additional handle Sound values according to EN 60745 Sound pressure level L 90 dB(A) Sound power L 101 dB(A) Uncertainty K 3 dB Wear hearing protection. Excessive noise can lead to hearing loss. Operating manual – angle grinder PAGS 10-115...
-
Page 12: Transport And Storage
• ambient temperature below 40 °C • protected from dust and direct sunlight inside the transport case 2. Check the additional handle (7) for tight fit. 3. For disassembly unscrew the additional handle (7) counter-clockwise. Operating manual – angle grinder PAGS 10-115... - Page 13 To adjust the guard (6), please proceed as follows: 1. Loosen the clamping screw (9). 3. Retighten the clamping screw (9) and check whether the guard (6) is properly locked in place. It must be impossible to rotate the guard. Operating manual – angle grinder PAGS 10-115...
- Page 14 5. Put the new cutting disc (12) on the mounting flange (10). The labelling must point to the device. Make sure that the cutting disc hole fits the mounting flange without clearance. Do not use any reducers or adapters. Operating manual – angle grinder PAGS 10-115...
- Page 15 Press and hold the spindle lock (1). 9. Retighten the clamping nut (11) by means of the pin-type face wrench (8). Then let go of the spindle lock (1). Pay attention not to damage the cutting disc. Operating manual – angle grinder PAGS 10-115...
-
Page 16: Operation
The on/off switch (2) returns to its initial • Always move the cutting disc through the workpiece in position. reverse rotation. Caution The disc keeps running after the device has been switched off. Risk of injury. Operating manual – angle grinder PAGS 10-115... -
Page 17: Available Accessories
• If required, allow the device to cool down. • Remove the tool from the device (see Start-up chapter). • Clean the device according to the Maintenance chapter. • Store the device according to the Storage chapter. Operating manual – angle grinder PAGS 10-115... -
Page 18: Errors And Faults
Tool change. • Make sure that there is no workpiece debris blocking the drive. Remove the blockages, if any. • Make sure that the cutting disc is not jammed in the workpiece. Operating manual – angle grinder PAGS 10-115... -
Page 19: Maintenance
• Remove dust from inside the guard, from the mounting flange and from the clamping nut. • Keep the ventilation openings free from dust deposits to prevent overheating of the motor. • For maintenance of the cutting disc, see chapter Tool change. Operating manual – angle grinder PAGS 10-115... - Page 20 Trotec GmbH & Co. KG Grebbener Str. 7 D-52525 Heinsberg +49 2452 962-400 +49 2452 962-200 info@trotec.com www.trotec.com...