1. Manuals
  2. Brands
  3. Trotec Manuals
  4. Grinder
  5. PBGS 10-120
  6. Original instructions manual

Trotec PBGS 10-120 Original Instructions Manual

Bench grinding machine
Hide thumbs
Table of Contents

Advertisement

Quick Links

Download this manual
PBGS 10-120
EN
ORIGINAL INSTRUCTIONS
BENCH GRINDING MACHINE

Advertisement

Table of Contents
loading
Need help?

Need help?

Do you have a question about the PBGS 10-120 and is the answer not in the manual?

Questions and answers

Related Manuals for Trotec PBGS 10-120

Summary of Contents for Trotec PBGS 10-120

  • Page 1 PBGS 10-120 ORIGINAL INSTRUCTIONS BENCH GRINDING MACHINE...

  • Page 2: Table Of Contents

    Note This signal word indicates important information (e.g. material damage), but does not indicate hazards. Info Information marked with this symbol helps you to carry out your tasks quickly and safely. bench grinding machine PBGS 10-120...

  • Page 3: Safety

    • If operating a power tool in a damp location is unavoidable, use a residual current device (RCD) protected supply. Use of an RCD reduces the risk of electric shock. bench grinding machine PBGS 10-120...
  • Page 4 General Power Tool Safety Warnings – Service • Have your power tool serviced by a qualified repair person using only identical replacement parts. This will ensure that the safety of the power tool is maintained. bench grinding machine PBGS 10-120...
  • Page 5 Damaged accessories will control. normally break apart during this test time. bench grinding machine PBGS 10-120...
  • Page 6 If a cutting wheel gets caught, it usually breaks. If rotary files, high-speed milling tools or carbide milling tools get caught, the tool insert may be ejected from the groove and cause loss of control of the power tool. bench grinding machine PBGS 10-120...
  • Page 7 10 mm. • Always provide for stable and secure conditions for the table sander when you mount it on a workbench or a similar surface. • Ensure that the grinding functions are carried out safely. bench grinding machine PBGS 10-120...
  • Page 8 – Leather flying pieces which could cause injuries. • Polishing whilst adhering to the technical data. Residual risks We recommend using the power tool with original Trotec Warning of electrical voltage accessories. Electric shock from insufficient insulation. Foreseeable misuse Check the device for damages and proper functioning Do not use the device for: before each use.
  • Page 9 Do not leave the packaging lying around. Children may use it as a dangerous toy. Caution Vibration emissions can cause a health hazard if the device is used for an extended period of time or if it is not properly handled and maintained. bench grinding machine PBGS 10-120...

  • Page 10: Information About The Device

    It is suited for activities like model construction and the use in wood and metal processing or for polishing jewellery. The device furthermore offers spark protection with swivel- mounted protective screens for safe working. Device depiction bench grinding machine PBGS 10-120...
  • Page 11 • 4 x Flat washers M4 Knurled screw • 2 x Spring washers M5 Workpiece supports • 4 x Spring washers M4 Tool holder • 1 x manual Handle of flexible shaft Setting wheel for speed selection On/off switch Machine sanding disc bench grinding machine PBGS 10-120...

  • Page 12: Transport And Storage

    All parts of an operating cycle must be taken into consideration for this (e.g. times at which the power tool is switched off and times when it is switched on but runs without load). bench grinding machine PBGS 10-120...

  • Page 13: Start-Up

    3. Remove the device and drill the holes into the base. 4. Insert the screws into the 4 holes for table assembly on the device base. 5. Screw the device to the base (e.g. table or workbench) using 4 screws and nuts. bench grinding machine PBGS 10-120...
  • Page 14 4. Repeat this assembly process on the other side of the device. 4. Repeat this assembly process on the other side of the device. bench grinding machine PBGS 10-120...
  • Page 15 2. Tighten the lock nut (3) in counter-clockwise direction. 4. Insert the tool required into the tool holder (34). 5. Tighten the clamping nut (43) in clockwise direction using the wrench (7). 6. Let go of the spindle lock (42). 7. Check the tool for tight fit. bench grinding machine PBGS 10-120...
  • Page 16 4. Place a cutting disc (9) or abrasive wheel (8) between the two washers (46) onto the screw (45) and tighten it to the mandrel again in clockwise direction. 5. Let go of the spindle lock (42). bench grinding machine PBGS 10-120...
  • Page 17 4. Place the abrasive belt (12) onto the rubberized holder and tighten the screw (45) again in clockwise direction. 3. Remove the collet chuck (13) from the collet chuck holder (44). 5. Let go of the spindle lock (42). bench grinding machine PBGS 10-120...
  • Page 18 (not water) in order to prevent chips from settling on the cutting edges of the tool, and to prevent the tool from being overheated. Connecting the power cable • Insert the mains plug into a properly secured mains socket. bench grinding machine PBGS 10-120...

  • Page 19: Operation

    • For tasks requiring precision, like for example engraving, polishing or sanding, you can also hold the tool between your thumb and index finger like a pen. The tapering of the housing on the lower part of the tool serves this purpose. bench grinding machine PBGS 10-120...

  • Page 20: Errors And Faults

    • Make sure not to exert too much pressure on the device during grinding. • Check whether the tool is suitable for the tasks to be carried out. • Keep the venting slots clear to prevent the motor from overheating. bench grinding machine PBGS 10-120...

  • Page 21: Maintenance

    The device still does not operate correctly after these for the change is not included in the scope of delivery. checks: Please contact the customer service. If necessary, bring the device to an authorised specialist electrical company or to Trotec for repair. bench grinding machine PBGS 10-120...
  • Page 22 9. Reattach the lateral protective cover (48). 10. Mount the screws (47) of the lateral protective cover (48). To do so, use a size T-10 Torx screwdriver. 11. Make sure that the tool is attached securely. bench grinding machine PBGS 10-120...

  • Page 23: Disposal

    Warning of electrical voltage Directive 2006/42/EC, Annex II, Part 1, Section A There is a risk of a short-circuit due to liquids We – Trotec GmbH – declare in sole responsibility that the penetrating the housing! product designated below was developed, constructed and Do not immerse the device and the accessories in produced in compliance with the requirements of the water.
  • Page 24 Trotec GmbH Grebbener Str. 7 D-52525 Heinsberg +49 2452 962-400 +49 2452 962-200 info@trotec.com www.trotec.com...

Table of Contents