Table of Contents
Advertisement
Quick Links
Advertisement
Table of Contents
Related Manuals for InHand ODU2002
Summary of Contents for InHand ODU2002
- Page 1 InHand ODU2002 Outdoor Unit Quick Installation Guide Data Version: V1.3...
-
Page 2: Table Of Contents
Panel Introduction ........................... 2 Equipment Installation ........................... 2 3.1 Insert SIM card ........................... 2 3.2 Attach antennas ..........................3 3.3 Install the ODU2002 ........................4 3.4 Cable installation ..........................6 3.4.1 Grounding..........................6 3.4.2 Connect the Ethernet Cable ....................7 3.4.3 Connect PoE Power Adapter ..................... -
Page 3: Overview
Overview This manual is for the installation and operation of the ODU2002 5G outdoor unit of Inhand Networks . Before installation, please confirm the product model and accessories in the package and purchase a SIM card from the operator that supports the local network. -
Page 4: Panel Introduction
Check for cables and antennas required for installation. ⚫ 3.1 Insert SIM card ODU2002 supports dual nano SIM cards ⚫ Unscrew the SIM card cover of the ODU2002, then insert the SIM card(s) according ⚫ to the following diagram. -
Page 5: Attach Antennas
Put the SIM card cover back in place, make sure the waterproof gasket is properly ⚫ assembled to prevent leakage. 3.2 Attach antennas Attach eight antennas to the TNC connectors marked 5G/5G MIMO/Wi-Fi and GNSS. ⚫... -
Page 6: Install The Odu2002
3.3 Install the ODU2002 3.3.1 Install the Mounting plate Attach the mounting plate to the ODU2002 using screws. Please make sure the top ⚫ side facing upwards. 3.3.2 Wall-mounted Installation Install the adjustable base on the wall in the desired angle and position. - Page 7 Attach the mounted ODU2002 to the base. Tighten the mounting bolts to lock the ⚫ ODU2002 in place. 3.3.3 Pole-mounted Installation Install the adjustable base on the pole in the desired angle and position. ⚫...
-
Page 8: Cable Installation
Attach the mounted ODU2002 to the base. Tighten the mounting bolts to lock the ⚫ ODU2002 in place. 3.4 Cable installation 3.4.1 Grounding Connect the grounding hole of the device to the ground through the grounding wire ⚫ with OT terminal, cut the grounding wire into certain length according to field... -
Page 9: Connect The Ethernet Cable
situation to avoid waste. 3.4.2 Connect the Ethernet Cable Notice (1) Please make sure that the ethernet cable is inserted into the device in a standardized way. If not, the crystal head may be damaged when installing the waterproof PG head. (2) When removing the ethernet cable, the waterproof PG head must be removed first, and then the crystal head connected to the device must be removed. -
Page 10: Connect Poe Power Adapter
3.4.3 Connect PoE Power Adapter Connect one end of the Ethernet cable to the PoE 2.5G LAN1 port and plug the other ⚫ end into the 802.af(50V/0.3A) PoE Adapter or an router/switch with 802.3af port. 3.5 Inspection after Installation 3.5.1 Check the Device Installation Confirm the device is fully secured to prevent falling. -
Page 11: Check The Cable Connection
Turn on the power to supply power to the device and confirm the device can work ⚫ normally. 4. Access to Internet ODU2002 supports two ways of accessing to Internet: cellular and wired. Wi-Fi is only used for configuration. 4.1 SIM Card Dial-up 4.1.1 Connect via APP Insert the SIM card when device is power off, and connect the 5G antenna to the ⚫... - Page 12 After adding the device, if the device fails to connect to the network, you can ⚫ click "Configure local device" to configure the device to connect to the cloud. The ODU2002 enables the http access and Wi-Fi AP function by default.
- Page 13 Scan the QR code on ODU2002, and then the APP will automatically connect to ⚫ the device via Wi-Fi. After the connection succeeds, APP will will automatically log in to the device and ⚫ enter the networking configuration interface, confirm the information and...
-
Page 14: Connect Via Pc
Step 1: Power off the device, insert the SIM card into the card slot, connect the ⚫ 5G antenna to the device, connect ODU2002 and PC with Ethernet cable. Step 2: Open a browser and enter the device's default address 192.168.1.1 in the ⚫... - Page 15 Step 4: Check the dial-up status in the "Interface Status" of the "Dashboard". The ⚫ device connects to the Internet successfully if the "Cellular" icon turns green. Click the "Cellular" icon to view information such as signal strength, IP address, and traffic consumption.
-
Page 16: Wired Networking
4.2 Wired Networking 4.2.1 Connect via APP Step1: Click the "Device" directory below to enter the [Device] page, click the ⚫ menu button in the upper right corner, and select [Add Device]. Scan the QR code on the ODU2002 to add device. - Page 17 After adding the device, if the device fails to connect to the network, you can ⚫ click "Configure local device" to configure the device to connect to the cloud. The ODU2002 enables the http access and Wi-Fi AP function by default.
-
Page 18: Configure Via Pc
Scan the QR code on the nameplate of the unit, then the APP will automatically ⚫ connect to the ODU via Wi-Fi. After the connection succeeds, APP will automatically log in to the device and enter ⚫ the networking configuration interface, confirm the information then submit. 4.2.1 Configure via PC Step 1: Connect the LAN1 port to the PC. - Page 19 Step 4: Click "Internet" on the left navigation bar to view the device interface ⚫ status. ODU2002 enables WAN1 with DHCP mode by default. ODU2002 supports three methods to allocate WAN address, dynamic DHCP (recommended), static IP and PPPoE. Click the Edit button next to WAN to modify the WAN port.
- Page 20 the upstream device. After the configuration is completed, the router will access the network through the specified static IP. PPPoE: Users can configure broadband dial-up. After the configuration is ⚫ completed, the router will access the network through broadband dial-up. Step 5: Verify network connectivity Via Ping tool in System/ Tools page.
-
Page 21: Remote Manage Platform
5. Remote Manage Platform 5.1 InCloud Platform 5.1.1 Register/login to the Platform Use a browser to visit InCloud, address: https://star.inhandcloud.com/, and enter ⚫ InCloud registration and login page. (Chrome is recommended) After registration, login to the cloud platform with the registered email. Enter the ⚫... -
Page 22: Adding Devices To The Platform
5.1.2 Adding devices to the Platform Log in to InCloud Manager platform, click "Device >> Add" in the navigation ⚫ menu to add your device by filling device’s serial number. 6. Quick User Guide 6.1 Restore to Default Factory Settings 6.1.1 Reset/Restore Remotely Log in to the InCloud Manager platform, click "Device >>... -
Page 23: Hardware Restore
6.1.2 Hardware Restore To restore to default settings by the reset button, please perform the following steps: When the unit power ON, press and hold the reset button for 5-10 seconds. ⚫ When System LED is steady on blue, release RESET button, system LED will blink ⚫... -
Page 24: Led Status Reference
7. LED Status Reference ODU2002NAVA ODU2002 Indicator light LED status and definition Off --- Power off Steady in --- System starting System Blink in --- System error Steady in green --- System working Blink in blue --- System upgrading Off --- Cellular disable...
Need help?
Do you have a question about the ODU2002 and is the answer not in the manual?
Questions and answers