Textron Greenlee HKL1232 Instruction Manual

Textron Greenlee HKL1232 Instruction Manual

Hydraulic crimping tool

Advertisement

Quick Links

Hydraulic Crimping Tool
52027337 REV 3
1.800.561.8187
INSTRUCTION MANUAL
HKL1232
Read and understand all of the instructions and
safety information in this manual before operating
or servicing this tool.
© 2016 Greenlee Textron Inc.
www.
information@itm.com
.com
Español ................. 9
Français .............. 17
7/16

Advertisement

Table of Contents
loading
Need help?

Need help?

Do you have a question about the Greenlee HKL1232 and is the answer not in the manual?

Questions and answers

Summary of Contents for Textron Greenlee HKL1232

  • Page 1 Español ....9 Français ....17 HKL1232 Hydraulic Crimping Tool Read and understand all of the instructions and safety information in this manual before operating or servicing this tool. 52027337 REV 3 © 2016 Greenlee Textron Inc. 7/16 1.800.561.8187 information@itm.com www. .com...
  • Page 2: Table Of Contents

    HKL1232 Hydraulic Crimping Tool Keep this manual available to all personnel. All specifications are nominal and may change as design improve- ments occur. Greenlee Textron Inc. shall not be liable for damages resulting from misapplication or misuse of its products. KEEP THIS MANUAL Greenlee / A Textron Company 1.800.561.8187...
  • Page 3: Important Safety Information

    Read and understand all of the instructions and safety information in this manual before operating or servicing this tool. Failure to observe this warning could result in severe injury or death. Greenlee / A Textron Company 1.800.561.8187 information@itm.com www. .com...
  • Page 4 Inspect tool before use. Replace any worn or damaged parts. A damaged or improperly assembled tool can break and strike nearby personnel. Failure to observe this warning could result in severe injury or death. Greenlee / A Textron Company 1.800.561.8187 information@itm.com www. .com...
  • Page 5: Identification

    5. Crimping Head Specifications Length ..................... 612.4 mm (24.12") Width ...................... 150 mm (5.9") Mass/Weight ..................6.5 kg (14.4 lb) Crimping Range ................8 AWG to 750 kcmil Crimping Force ................... 106 kN (12 tons) Greenlee / A Textron Company 1.800.561.8187 information@itm.com www. .com...
  • Page 6: Operation

    • The handle load will drop suddenly to indicate a completed crimp. If the handle load does not drop suddenly, the crimp is not complete. Failure to observe these warnings could result in severe injury or death. Greenlee / A Textron Company 1.800.561.8187 information@itm.com www. .com...
  • Page 7: Periodic Pressure Relief Valve Check

    9. When using KC12-type dies, complete the number of crimps listed on the “Connector Selection” chart in this manual. For other dies, complete the number of crimps specified by the manufacturer. 10. Remove connector from crimping tool. Greenlee / A Textron Company 1.800.561.8187 information@itm.com www. .com...
  • Page 8: Die Selection

    60101 to Dual-rated ACL/ACN column instead of the YA-A 60176; 400 to Aluminum VACL 2ACL/2ACN BLUA number provided with YA-ATN 60230 to 750 kcmil: Lugs ALNS/ALNN/ALND the connector. 60278 3 crimps Greenlee / A Textron Company 1.800.561.8187 information@itm.com www. .com...
  • Page 9: Español

    HKL1232 Hydraulic Crimping Tool Illustration / Ilustración / Illustration Greenlee / A Textron Company 1.800.561.8187 information@itm.com www. .com...
  • Page 10: Parts List

    Pump handle kit lt 48 Dust seal ............1 52027507 Piston seal kit 50017764 Washer ............3 52027503 Pivot pin kit 50 50017969 Handle head ...........1 52027506 Reservoir handle kit n 51 Pin ..............1 Greenlee / A Textron Company 1.800.561.8187 information@itm.com www. .com...

Table of Contents