Advertisement
Execution Command List (4/4)
Command Set
Command
Pan-tiltDrive
Up
Down
Left
Right
UpLeft
UpRight
DownLeft
DownRight
Stop
AbsolutePosition
RelativePosition
Home
Reset
Pan-tiltLimitSet
LimitSet
LimitClear
Pan-tiltSet SlowPanTilt
On
Off
Tally Lamp
ON
OFF
1) After the ACK for One Push WB Trigger is issued, "Not Executable" is returned to all commands until the operation is completed.
2) Bright is set only in the mode of Full Auto or Shutter Priority.
3) Does not operate when the menu is displayed.
4) Do not turn off the power of this unit before the response to the command is returned.
In case that the power is turned off, the image may not be output correctly.
In such case, try to execute the operation using the different setting value once, and then execute the operation using the correct setting
value.
5) Do not turn off the power of this unit before the response to the command is returned.
In case that the power is turned off, the setting may not be reflected correctly.
In such case, try to execute the operation using the different setting value once, and then execute the operation using the correct setting
value.
6) To specify the position of pan/tilt, 15-byte message length data (17 bytes including header and terminator) is required.
Command Packet
8x 01 06 01 VV WW 03 01 FF
3)
8x 01 06 01 VV WW 03 02 FF
3)
8x 01 06 01 VV WW 01 03 FF
3)
8x 01 06 01 VV WW 02 03 FF
3)
8x 01 06 01 VV WW 01 01 FF
3)
8x 01 06 01 VV WW 02 01 FF
3)
8x 01 06 01 VV WW 01 02 FF
3)
8x 01 06 01 VV WW 02 02 FF
3)
8x 01 06 01 VV WW 03 03 FF
3)
8x 01 06 02 VV 00
6)
0Y 0Y 0Y 0Y 0Y 0Z 0Z 0Z 0Z 0Z FF
8x 01 06 03 VV 00
6)
0Y 0Y 0Y 0Y 0Y 0Z 0Z 0Z 0Z 0Z FF
8x 01 06 04 FF
8x 01 06 05 FF
8x 01 06 07 00 0W
6)
0Y 0Y 0Y 0Y 0Y 0Z 0Z 0Z 0Z 0Z FF
8x 01 06 07 01 0W
6)
07 0F 0F 0F 0F 07 0F 0F 0F 0F FF
8x 01 06 44 02 FF
8x 01 06 44 03 FF
8x 01 7E 01 0A 00 02 FF
8x 01 7E 01 0A 00 03 FF
Comments
VV: Pan speed setting 0x01 (low speed) to 0x18
(high speed)
WW: Tilt speed setting 0x01 (low speed) to 0x18
(high speed)
YYYYY: Pan Position EAC00 to 15400 (CENTER 00000)
ZZZZZ: Tilt Position FC400 to 0B400
W: 1 UpRight
YYYYY: Pan Limit Position EAC01 to 15400
ZZZZZ: Tilt Limit Position FC401 to 0B400
(Image Flip: OFF)
Tilt Limit Position F4C01 to 03C00
(Image Flip: ON)
W: 0 DownLeft
YYYYY: Pan Limit Position EAC00 to 153FF
ZZZZZ: Tilt Limit Position FC400 to 0B3FF
(Image Flip: OFF)
Tilt Limit Position F4C00 to 03BFF
(Image Flip: ON)
Pan/Tilt Slow Mode On/Off
Tally lamp ON/OFF
1
(Image Flip: OFF) (CENTER 00000)
Tilt Position F4C00 to 03C00
(Image Flip: ON) (CENTER 00000)
Advertisement
