Sargent and Greenleaf 6124 Reference Manual

Change from Multiple-User to Dual-User—This non-reversible function change must be done before the factory Master Code
is changed for the first time. You will need to use the Dual-User Reference Guide after function change. See page 3. Change
the factory set Management Reset Code to a code of your own choosing. This change must be made before the factory Mas-
ter Code is changed for the first time.
Reset the Lock's Factory Programmed Management Reset Code (MRC) to a Code of Your Own Choosing
e e e e e
6 7 * 1 2 3 4 5 6 # (
Note: The MRC can only be changed at the keypad by using the factory default master code of 1 2 3 4 5 6 before the master code is changed for the
first time. The MRC is a 7-digit code which contains a .01. digit pair that may appear anywhere in the MRC code. The .01. pair must be pressed at the
same time. All other MRC code digits are pressed individually. An example of a Management Reset
Code is 3518.01.9 with the digits to be pressed simultaneously grouped between periods. This means the 0 and 1 would be pressed at the same time
when entering the code.
Opening the Lock using the Factory Default Code
The factory default Master Code is 1 2 3 4 5 6. To open the lock, enter 1 2 3 4 5 6 # then operate the safe's handle.
Changing Your Own Code or Factory Default Code
2 2 * YOUR OLD CODE # (
Creating a New Code (Supervisor or User Code)
7 4 * MASTER CODE OR SUPERVISOR CODE # (
e e e
PIN POSITION # ( ) NEW CODE # (
PIN Positions: 1 Supervisor Code
2 – 9 User Codes (
Deleting a Code (Supervisor or User Code)
7 4 * MASTER CODE OR SUPERVISOR CODE # (
PIN Positions: 1 Supervisor Code
2 – 9 User Codes (
Note: The Master Code cannot be deleted. The Supervisor Code cannot be used to delete itself. A time delay override code can only be deleted during
an opening window period.
Changing the Length of the Opening Window
e e e e e
7 4 * MASTER CODE # (
LENGTH OF DESIRED OPENING WINDOW # (
Note: The opening window period can be set anywhere from 1 to 99 minutes. If a lock is using time delay, the opening window period can only be
changed during an opening window period.
Setting, Changing, or Deleting a Time Delay
e e e e e
7 4 * MASTER CODE # (
( LENGTH OF DESIRED TIME DELAY # (
Note: The time delay period can be set anywhere from 1 to 99 minutes. An existing time delay can only be changed during an opening window period.
To delete a time delay, enter the length of desired time delay as zero.
Creating a Time Delay Override Code
7 4 * MASTER CODE OR SUPERVISOR CODE # (
NEW TIME DELAY OVERRIDE CODE # (
Note: The Time Delay Override Code only works if Time Delay Override is turned on and the lock has a time delay period programmed.
Turning On Time Delay Override Function
e e e e e
4 6 * MASTER CODE # (
e e e
Control TDO # ( )
6124, 6125 Multiple-User Mode Reference Guide
e e e
) NEW MRC # ( ) NEW MRC # (
e e e e e
) NEW CODE # (
e e e e e
e e e
) NEW CODE # (
User Code 9 only performs as a regular User Code when the time delay override feature is turned off.
e e e e e
Code 9 acts as a regular User Code when the time delay override feature is turned off.
e e e
) 0 1 # ( )
e e e
) 0 0 #
e e e
) LENGTH OF DESIRED TIME DELAY # (
e e e e e
e e e
) NEW TIME DELAY OVERRIDE CODE # (
) 1 for Dual Control TDO or 2 for Single Control TDO # (
1
IMPORTANT NOTICE:
e e e
)
e e e e e e
) NEW CODE # (
)
e e e
)
) PIN POSITION # (
) LENGTH OF DESIRED OPENING WINDOW # (
) 9 #
Document 630-764 (revised 05/09/2023)
)
)
e e e e e e e e e
) # ( ) # ( )
)
e e e
e e e
)
e e e
)
e e e
) 1 for Dual Control TDO or 2 for Single
Sargent & Greenleaf, Inc.
One Security Drive
Nicholasville, KY 40356
Phone: (800)-826-7652 Fax: (800)-634-4843
Phone: (859)-885-9411 Fax: (859)-887-2057
)