Download
Share
Print this page
ICP DAS USA M-7019Z Quick Start Manual
  1. Manuals
  2. Brands
  3. ICP DAS USA Manuals
  4. Control Unit
  5. M-7019Z
  6. Quick start manual

ICP DAS USA M-7019Z Quick Start Manual

10-channel universal voltage input & current input, thermocouple input module
Hide thumbs
1
2
3
4
5
6
7
8

Advertisement

Quick Links

Download this manual
M-7019Z
10-channel Universal Voltage Input & Current
Input, thermocouple input Module
Quick Start Guide
Product Website:
http://www.icpdas-usa.com/m_7019z.html
http://www.icpdas-usa.com/dcon_utility_pro.html
1. Introduction
M-7019Z is an RS-485 interface and 10-channel thermocouple input module. The
analog input range is software selectable and supports +/-15 mV, +/-100 mV, +/-150mV,
+/-500 mV, +/-1 V, +/-2.5 V, +/-5 V, +/-V10, +/-20 mA, 0 ~ 20 mA, and thermocouple of
type J, K, T, E, R, S, B, N, C, L, M, and LDIM43710. I-87019ZW uses external terminal
design, and takes thermocouple temperature output consistency.
2. Terminal Assignment
M-7019Z 10-channel Thermocouple, Current and Voltage AI Module- QuickStart (Sep/2017)
ICP DAS USA, Inc. |
www.icpdas-usa.com
| 1-310-517-9888 | 24309 Narbonne Ave. Suite 200. Lomita, CA 90717
1

Advertisement

loading

Related Manuals for ICP DAS USA M-7019Z

Summary of Contents for ICP DAS USA M-7019Z

  • Page 1 1. Introduction M-7019Z is an RS-485 interface and 10-channel thermocouple input module. The analog input range is software selectable and supports +/-15 mV, +/-100 mV, +/-150mV, +/-500 mV, +/-1 V, +/-2.5 V, +/-5 V, +/-V10, +/-20 mA, 0 ~ 20 mA, and thermocouple of type J, K, T, E, R, S, B, N, C, L, M, and LDIM43710.

  • Page 2: Block/ Wiring Diagram

    3. Block/ Wiring Diagram M-7019Z 10-channel Thermocouple, Current and Voltage AI Module- QuickStart (Sep/2017) ICP DAS USA, Inc. | www.icpdas-usa.com | 1-310-517-9888 | 24309 Narbonne Ave. Suite 200. Lomita, CA 90717...

  • Page 3: Default Settings

    M-7019Z Jumper Settings The M-7019Z can accept current inputs from –20mA to 20mA. No external resistor required but the corresponding jumper must be shorted. The following figure shows the jumper positions. 4. Default Settings Default settings for the M-7017, M-7018 and M-7019 series modules are: ▫...
  • Page 4 3. Connect the module to the power supply using the +Vs and GND terminals. Note that the voltage supplied should be in the range of +10 to +30V DC. M-7019Z 10-channel Thermocouple, Current and Voltage AI Module- QuickStart (Sep/2017) ICP DAS USA, Inc. | www.icpdas-usa.com...
  • Page 5 It can select multi-options such as Baud Rate, Protocol, Checksum, and Format to search module. The default settings for the module can be found in Section 3. Click OK after selecting the COM port setting. M-7019Z 10-channel Thermocouple, Current and Voltage AI Module- QuickStart (Sep/2017) ICP DAS USA, Inc. | www.icpdas-usa.com...
  • Page 6 DCON Utility Pro supports DCON and Modbus protocol for all ICPDAS and the others modules. 6. Configuration I/O module setting on PC M-7019Z 10-channel Thermocouple, Current and Voltage AI Module- QuickStart (Sep/2017) ICP DAS USA, Inc. | www.icpdas-usa.com...
  • Page 7 For M-7000 modules using the Modbus RTU protocol, use Function 04h to read the data from the input channels. See user manual Section 3.2 for details. M-7019Z 10-channel Thermocouple, Current and Voltage AI Module- QuickStart (Sep/2017) ICP DAS USA, Inc. | www.icpdas-usa.com...
  • Page 8 If user doesn’t know command, user can select Address and ID, it will show some refer commands as below. User can select necessary command to test or debug modules. M-7019Z 10-channel Thermocouple, Current and Voltage AI Module- QuickStart (Sep/2017) ICP DAS USA, Inc. | www.icpdas-usa.com...