Advertisement
Quick Links
M-7026
6-ch Analog Input, 2-ch Analog Output, 3-ch
Digital Input and 3-ch Digital Output Data
Acquisition Module
Quick Start Guide
Product Website:
https://www.icpdas-usa.com/m_7026.html
http://www.icpdas-usa.com/dcon_utility_pro.html
1. Introduction
The M-7026 is a Modbus RTU based multifunction module with 6 analog inputs, 2
analog outputs, 3 digital inputs, and 3 digital outputs . It provides a programmable input
range on all analog inputs (+/-150 mV, +/-500 mV, +/-1 V, +/-5 V, +/-10 V, +/-20 mA or 0
~ +20 mA). The analog outputs are 12-bit at +/-5 V, +/-10 V, 0 ~ +20 mA or +4 ~ +20
mA. All digital outputs can be set as alarm outputs. Each analog input can be
configured for an individual range and provides a high overvoltage protection of 240
Vrms. Voltage and current inputs/outputs are jumper selectable.
2. Terminal Assignment
M‐7026 6‐ch AI, 2‐ch AO, 3‐ch DI and 3‐ch DO DAQ Module ‐ QuickStart (Mar/2019)
ICP DAS USA, Inc. |
www.icpdas-usa.com
| 1-310-517-9888 | 24309 Narbonne Ave. Suite 200. Lomita, CA 90717
1
Advertisement
Related Manuals for ICP DAS USA M-7026
Summary of Contents for ICP DAS USA M-7026
- Page 1 1. Introduction The M-7026 is a Modbus RTU based multifunction module with 6 analog inputs, 2 analog outputs, 3 digital inputs, and 3 digital outputs . It provides a programmable input range on all analog inputs (+/-150 mV, +/-500 mV, +/-1 V, +/-5 V, +/-10 V, +/-20 mA or 0 ~ +20 mA).
-
Page 2: Block/ Wiring Diagram
3. Block/ Wiring Diagram M‐7026 6‐ch AI, 2‐ch AO, 3‐ch DI and 3‐ch DO DAQ Module ‐ QuickStart (Mar/2019) ICP DAS USA, Inc. | www.icpdas-usa.com | 1-310-517-9888 | 24309 Narbonne Ave. Suite 200. Lomita, CA 90717 2 ... -
Page 3: Default Settings
4. Default Settings The default settings for the M-7026 are: ・ Module Address: 01 ・ Analog Input Type: Type 08, -10 V to +10 V ・ Analog Output Type: Type 3, -10 V to +10 V ・ Protocol: Modbus RTU ・... - Page 4 M‐7026 6‐ch AI, 2‐ch AO, 3‐ch DI and 3‐ch DO DAQ Module ‐ QuickStart (Mar/2019) ICP DAS USA, Inc. | www.icpdas-usa.com | 1-310-517-9888 | 24309 Narbonne Ave. Suite 200. Lomita, CA 90717 4 ...
- Page 5 3. Connect the module to the power supply using the +Vs and GND terminals. Note that the voltage supplied should be in the range of +10 to +30V DC. M‐7026 6‐ch AI, 2‐ch AO, 3‐ch DI and 3‐ch DO DAQ Module ‐ QuickStart (Mar/2019) ICP DAS USA, Inc. | www.icpdas-usa.com | 1-310-517-9888 | 24309 Narbonne Ave. Suite 200. Lomita, CA 90717 ...
- Page 6 The default settings for the module can be found in Section 3. Click OK after selecting the COM port setting. M‐7026 6‐ch AI, 2‐ch AO, 3‐ch DI and 3‐ch DO DAQ Module ‐ QuickStart (Mar/2019) ICP DAS USA, Inc. | www.icpdas-usa.com | 1-310-517-9888 | 24309 Narbonne Ave. Suite 200. Lomita, CA 90717 ...
- Page 7 DCON Utility Pro supports DCON and Modbus protocol for all ICPDAS and the others modules. 6. Configuration I/O module setting on PC M‐7026 6‐ch AI, 2‐ch AO, 3‐ch DI and 3‐ch DO DAQ Module ‐ QuickStart (Mar/2019) ICP DAS USA, Inc. | www.icpdas-usa.com | 1-310-517-9888 | 24309 Narbonne Ave. Suite 200. Lomita, CA 90717 ...
- Page 8 For M-7000 modules using the Modbus RTU protocol, use Function 04h to read the data from the input channels. See user manual Section 3.2 for details. M‐7026 6‐ch AI, 2‐ch AO, 3‐ch DI and 3‐ch DO DAQ Module ‐ QuickStart (Mar/2019) ICP DAS USA, Inc. | www.icpdas-usa.com | 1-310-517-9888 | 24309 Narbonne Ave. Suite 200. Lomita, CA 90717 ...
- Page 9 If user doesn’t know command, user can select Address and ID, it will show some refer commands as below. User can select necessary command to test or debug modules. M‐7026 6‐ch AI, 2‐ch AO, 3‐ch DI and 3‐ch DO DAQ Module ‐ QuickStart (Mar/2019) ICP DAS USA, Inc. | www.icpdas-usa.com | 1-310-517-9888 | 24309 Narbonne Ave. Suite 200. Lomita, CA 90717 9 ...
Need help?
Do you have a question about the M-7026 and is the answer not in the manual?
Questions and answers