Parameter Setting - DEMA IMPERIA Operation And Maintenance Manual

4.2. Parameter setting

Settings menu structure
SETTING
Enter into "SETTING" interface
After switching on the display, briefly press (<0.5S) for two times to enter into the "SETTING"
interface. The interface includes the three options as "Display setting", "Information" and "EXIT".
Briefly press (<0.5S) + or - to switch the options and then briefly press (<0.5S) to confirm and enter
into the option. Select "EXIT" and briefly press (<0.5S) to exit the interface or briefly press (<0.5S)
for two times in any interface. The set dates are saved for the two exit modes. If there is no any
operation within 20S and then exit the set interface, no any dates are saved.
Enter into "Display setting" interface
In the "SETTING" interface, briefly press (<0.5S) + or - to select "Display setting" and then
briefly press (<0.5S) to confirm and enter into "Display setting". There are thirteen set op-
tions in the interface.
Briefly press for two times (interval time is less than 0.5S) to exit back to the main interface, or
select "BACK" → "EXIT" to back the main interface.
1. Unit
Unit switches between the km and mile. Briefly press (<0.5S)
+ or - to select "Unit", and then briefly press (<0.5S) to enter
into the set interface. Briefly press (<0.5S) + or - to select Met-
ric/Imperial, and then briefly press (<0.5S) to save the set and
exit back to the Unit interface.
34 EN
Unit
Brightness
Auto Off
Power View
SOC View
Display Setting
TRIP Reset
AL Sensitivity
Password
Set clock
BACK
Wheel
Speed Llimit
Battery info.
Information
Error Code
BACK
EXIT
E-bike operation and maintenance manual
2. Brightness
Set display brightness. Briefly press (<0.5S) + or - to select "Brightness" and then briefly press (<0.5S)
. This moment, briefly press (<0.5S) + or - to switch the percentage as 100%/75%/50%/30%/10%.
100% is the highest brightness, 10% is lowest brightness. After selecting the brightness percent-
age, briefly press (<0.5S) again to save the set and exit back to "Brightness".
3. Auto Off
Set automatic Off time. Briefly press (<0.5S) + or - to select "Auto Off", and then briefly press
(<0.5S) . This moment switch automatic Off time as OFF/9/8/7/6/5/4/3/2/1. The unit is
minute. After selection, briefly press (<0.5S) to save the set and exit back to "Auto Off".
4. Power View
Set output display mode. Briefly press (<0.5S) + or - to se-
lect "Power View", and then briefly press (<0.5S) . This mo-
ment, briefly press (<0.5S) + or - to switch the output display
mode as "Power"/"Current". After confirmation, briefly press
(<0.5S) again to save the set and exit back to "Power View".
5. SOC View
Set indication mode for battery capacity. Briefly press (<0.5S) +
or - to select "SOC View", and then briefly press (<0.5S) . This
moment switch display mode for output as "Percent"/"Voltage".
After confirmation, briefly press (<0.5S) to save the set and exit back to "SOC View".
6. TRIP Reset
Set reset function for single-trip distance. Briefly press (<0.5S) + or - to select "TRIP Reset", and then
briefly press (<0.5S) . This moment, briefly press (<0.5S) + or - to switch between "NO"and"YES".
TRIP Reset includes maximum speed (MAXS), average speed (AVG), single-trip distance (TRIP).
After confirmation, briefly press (<0.5S) again to save the set and exit back to the "TRIP Reset".
7. AL Sensitivity
Set light sensitivity. Briefly press (<0.5S) + or - to select "AL Sensitivity", and then briefly press
(<0.5S) . This moment switch level of the light sensitivity between 0/1/2/3/4/5/OFF. "OFF"
means close the function. Level 1 is the weakest light sensitivity and level 5 is the strongest
light sensitivity. Select the level desired and briefly press (<0.5S) again to save the setting
and exit back to "AL Sensitivity".
8. Password
Access password setting. Briefly press (<0.5S) + or - to select "Password" and then briefly press
(<0.5S) . This moment select "Start PassWord" and then briefly press (<0.5S)
press (<0.5S) + or - to switch between "OFF"/"ON", the below is the specific way of switching.
Starting password:
Enter into the "Start PassWord" interface and select "ON". Briefly press (<0.5S) , and then it shows
the input password in the interface. This moment switch numbers "0-9", and then briefly press
(<0.5S) to confirm the input number. After input, it shows theinput password again in the inter-
face. Repeat the above step to input the password again. If the password is the same as the previ-
ous time, the system will prompt if it is successful to set the password. After setting the password,
the interface exits back automatically to the original interface within two seconds.
E-bike operation and maintenance manual
again. Briefly
EN 35