Table of Contents
Advertisement
Quick Links
E
Operating
Instructions and
Repair Parts List
READ THIS BOOK
This book has important information for the use and safe operation of this machine. Failure to read
this book prior to operating or attempting any service or maintenance procedure to your Clarke
machine could result in injury to you or to other personnel; damage to the machine or to other property
could occur as well. You must have training in the operation of this machine before using it. If your
operator(s) cannot read this manual, have it explained fully before attempting to operate this machine.
All directions given in this book are as seen from the operator's position at the rear of the machine.
For new books write to: Clarke
Form No. 70676A
9/02
®
, 2100 Highway 265, Springdale, Arkansas 72764.
®
Clarke
Division of
S12, S16
S12cc, S12PF
Upright Vacuum
Printed in the U.S.A.
Advertisement
Table of Contents
Subscribe to Our Youtube Channel
Related Manuals for Alto Clarke S12PF
Summary of Contents for Alto Clarke S12PF
- Page 1 Division of S12, S16 Operating S12cc, S12PF Instructions and Upright Vacuum Repair Parts List READ THIS BOOK This book has important information for the use and safe operation of this machine. Failure to read this book prior to operating or attempting any service or maintenance procedure to your Clarke machine could result in injury to you or to other personnel;...
-
Page 2: Table Of Contents
Table of Contents Operator Safety Instructions ................... 3 Grounding Instructions .................... 5 Consignes de sécurité de l'utilisateur ..............6 Instructions visant la mise a la terra ................ 8 How to Prepare the Machine For Operation ............9 How to Operate the Machine .................. 9 Maintenance ...................... -
Page 3: Operator Safety Instructions
OPERATOR SAFETY INSTRUCTIONS WARNING AVERTISSEMENT ADVERTENCIA For the safe operation of this machine, read and understand all dangers, warnings and cautions. Look for these symbols: DANGER: If you do not follow the instructions in a DANGER, severe bodily injury or death can occur to the operator and/or other personnel. - Page 4 WARNING: To reduce the risk of fire, electric shock, or injury: 16. Belt pulleys can become hot during normal use. To prevent burns, avoid touching the belt pulley when servicing the drive belt. 17. Do not use to pick up flammable or combustible liquids such as gasoline, or use in areas where they may be present.
-
Page 5: Grounding Instructions
GROUNDING INSTRUCTIONS Grounded Preparation: Outlet Box The following are instructions for connection to the power supply and the electrical ground. This machine must be connected to the electrical ground to protect the operator from electrical shock. The machine has an approved power cord with three conductors and a plug with three terminals. -
Page 6: Consignes De Sécurité De L'utilisateur
CONSIGNES DE SÉCURITÈ DE L'UTILISATEUR AVERTISSEMENT Pour utiliser cet appareil en toute sécurité, il faut lire et coprendre tous les consignes de danger, d'avertissement et d'attention. Soyez attentif aux symboles que voici. DANGER: Ne pas respecter les consignes d'un avis de DANGER, peut occasionner la mort ou des lesions corporelles graves pour l'utilisateur et/ou d'autres pesonnes. - Page 7 AVERTISSEMENT: Pour réduire le risque de feu, de choc électrique, ou de blessure: 16. Ne remassez pas de objets qui brûient ou fument comme les cigarettes, les allumettes ou les cendres chaudes. 17. Les poulies de la courroie peuvent devenir chaudes pendant l'utilisation normale. Pour prévenir des brûlures, évitez de toucher la poulie lors de l'entretien de la courroie.
-
Page 8: Instructions Visant La Mise A La Terra
INSTRUCTIONS VISANT LA MISE A LA TERRE PREPARATION: Boîte de Prise Consignes pour brancher l'appareil a la source d'energie de Terre et pour la mise à la terre. Cet appareil doit être mise à la terre afin d'eviter le risque de choc électrique. -
Page 9: How To Prepare The Machine For Operation
HOW TO PREPARE THE MACHINE FOR OPERATION Assemble the Handle Attach upper (A) and lower (B) handle to handle socket (C) by aligning holes and securing with 2 part screws (D). See figure 1. Install the Bag Assembly Position the bag coupling into the left bag support (A) and turn the bag knob (B) counterclockwise to secure bag to base. -
Page 10: Maintenance
MAINTENANCE This section describes the procedures that must be Motor Pulley done by the operator. WARNING: To prevent injury, always turn off the switch and remove the electrical plug from the electrical outlet before changing the brush, belt, or filter bag and before leaving the machine. -
Page 11: What To Do About The Wear Of The Brush
MAINTENANCE (CONT.) 9. Place the rubber end cap covers over both end caps (flat side against end cap). Align holes and secure. Then, slant the brush roll forward so the end caps are in line with the slots in the cleaner base. -
Page 12: Steel Core Brush
MAINTENANCE (CONT.) Steel Core Brush WARNING: Turn off the switch and disconnect unit from electrical supply before replacing brush strips. 1. New brush strips inserts are supplied in sets. To replace, first disconnect the machine from the electrical outlet. 2. Remove the brush roll, see the section "How to Replace the Belt."... -
Page 13: Trouble Shooting Guide
TROUBLE SHOOTING GUIDE PROBLEM POSSIBLE CAUSE SOLUTION Motor does not run. 1) Not firmly plugged in. 1) Check attachment plug. 2) Bad On-Off switch. 2) Replace switch. 3) Line open. 3) Replace cord. 4) Motor open. 4) Check motor and wiring. 5) Fan locked by material. -
Page 14: Collector Cup Assembly Drawing 9/02
® Clarke Upright Vacuum Collector Cup Assembly Drawing 9/02 ® Clarke Page -14- Upright Vacuum Operator's Manual... -
Page 15: Collector Cup Assembly Parts List 9/02
® Clarke Upright Vacuum Collector Cup Assembly Parts List 9/02 Ref. Part No. Description 80065A Screw (M4 *10) 56489A Screw (M4 *15) E-clip (E6) 56485A Screw (M4 * 8) 30138A Handle Grip 51240A Handle Assembly, Upper 30143A Bag Hook 30144A Bag Retainer 30142A Cord Retainer, Upper... -
Page 16: Base Assembly Drawing 9/02
® Clarke Upright Vacuum Base Assembly Drawing 9/02 ® Clarke Page -16- Upright Vacuum Operator's Manual... - Page 17 ® Clarke Upright Vacuum Base Assembly Parts List 9/02 Ref. Part No. Description Qty. Ref. Part No. Description Qty. 51229B Hood and Graphics 51261A Clamp, Front Axle 80065A Screw (M4 *10) Screw (M3*10) 51949A Cable Clip 52807A Drive Belt 80066A Screw (M4* 18.5) 51253A 12"...
-
Page 18: Handle And Filter Bag Assembly Drawing 9/02
® Clarke Upright Vacuum Handle and Filter Bag Assembly Drawing 9/02 ® Clarke Page -18- Upright Vacuum Operator's Manual... -
Page 19: Handle And Filter Bag Assembly Parts List 9/02
® Clarke Upright Vacuum Handle and Filter Bag Assembly Parts List 9/02 Ref. Part No. Description Qty. 56489A Screw (M4*15) E-Clip (E6) 56485A Screw (M4*8) 30138A Handle Grip 51240A Handle Assembly - Upper Chrome 30143A Bag Hook 30144A Bag Retainer 30142A Cord Retainer- Upper Screw (M4*25) - Page 20 NOTES ® Clarke Page -20- Upright Vacuum Operator's Manual...
- Page 21 Caringbah NSW 2229 Clarke ® , Carlstadt, New Jersey 07072 +61 2 9524 6122 150 Commerce Road (201) 460-4774 ALTO Cleaning Systems Asia Pte Ltd., Singapore No. 17 Link Road Clarke ® , Elk Grove, Illinois 60007 Singapore 619034 2280 Elmhurst Road...
- Page 22 Clarke ® U.S. WARRANTY This Clarke Industrial/Commercial Product is warranted to be free from defects in materials and workmanship under normal use and service for a period of one year from the date of purchase, when operated and maintained in accordance with Clarke's Maintenance and Operations instructions. This warranty is extended only to the original purchaser for use of the product.
Need help?
Do you have a question about the Clarke S12PF and is the answer not in the manual?
Questions and answers