Table of Contents
Advertisement
•
when the coffee in the cup reaches the required level, press
the same button again to memorise the new amount.
The machine is now reprogrammed with the new quantities.
9.3 Adjusting the coffee mill
The coffee mill is set by default to prepare coffee correctly and
should not require regulating initially.
However, if after making the first few coffees you find that the
coffee is either too weak and not creamy enough or delivery is
too slow (a drop at a time), this can be corrected by adjusting
the grinding adjustment dial «A2» «fig. 13».
Please note:
The grinding adjustment dial must only be turned when the
coffee mill is in operation during the initial phase of coffee
preparation.
If the coffee is delivered too slowly or
not at all, turn one click clockwise.
For fuller bodied creamier coffee, turn
one click anticlockwise (do not turn
more than one click at a time other-
wise the coffee could be delivered a
drop at a time).
These adjustments will only be evident after at least 2 cups of
coffee have been delivered. If this adjustment does not produce
the desired result, turn the dial another click.
9.4 Setting the temperature
To change the temperature of the water used to make the cof-
fee, proceed as follows:
1. Confirm with the
be plugged into the mains socket and the main switch
«A8» (if present) must be in the I position «fig. 3»).
2. Press the
button «B3» (on the left of the dial «B6») and
hold down until the lights on the control panel come on;
3. Press the
button to select the required temperature:
LOW
4. Press the
button «B8» (on the right of the dial «B6»)
to confirm the selection. The lights go off.
Please note:
Varying the temperature has most effect for long beverages.
9.5 Tips for a hotter coffee
For hotter coffee, you should:
•
before delivering the coffee perform a rinse cycle by press-
ing the
button «B5»). Hot water is delivered from
button «B2». (The appliance must
HIGH
the spouts «A12», heating the internal circuits of the appli-
ance and thus raising the coffee temperature.
•
warm the cups by rinsing them with hot water (using the
hot water function).
•
set a hotter coffee temperature (see section "9.4 Setting
the temperature").
10. MAKING COFFEE USING COFFEE BEANS
Important!
Do not use caramelised or candied coffee beans as they could
stick to the coffee mill and damage it.
1. Fill the container «A7» with coffee beans «fig. 15».
2. Place under the coffee spouts «A12»:
• 1 cup, to make 1 coffee «fig. 16»;
• 2 cups, to make 2 coffees «fig. 17».
3. Lower the spouts as near as possible to the cup. This makes
a creamier coffee «fig. 18».
4. Press the button corresponding to the required coffee:
1 short coffee
2 short coffees
5. Preparation begins and the light corresponding to the se-
lected button flashes on the control panel.
Once the coffee has been made, the appliance is ready to make
the next beverage.
Please note:
•
While the machine is making coffee, delivery can be in-
terrupted at any moment by pressing one of the coffee
buttons.
•
At the end of delivery, to increase the quantity of coffee
in the cup, just press one of the coffee icons (within 3
seconds).
•
For hotter coffee, see section "9.5 Tips for a hotter coffee".
Important!
•
If the coffee is delivered a drop at a time, too weak and not
creamy enough or too cold, read the tips in section "17.
Troubleshooting".
•
Lights may light up on the control panel during use. Their
meaning is given in section "16. Explanation of lights".
10.1 Making coffee using pre-ground coffee
Important!
•
Never place coffee beans in the
pre-ground coffee funnel «A6» as
this could damage the appliance.
•
Never add pre-ground coffee
when the machine is off or it
10
1 long coffee
2 long coffees
Hide quick links:
Advertisement
Table of Contents
Troubleshooting
