Table of Contents
Advertisement
Quick Links
Advertisement
Table of Contents
Subscribe to Our Youtube Channel
Related Manuals for TW Audio BLS
Summary of Contents for TW Audio BLS
- Page 1 Assembly Instructions...
- Page 2 Thank you for choosing a high-quality product “MADE IN GERMANY” from the brand TW AUDiO. The BLS Boxlink connector set is an accessory part for products of the VERA10, VERA20 and VERA36 series. It is characterized by a subtle look, a remarkable size to weight ratio and ease of use.
- Page 3 Notes on the products Before using the boxlink connector set, carefully read the assembly instructions and keep the Read manual instructions in a safe place together with the BLS boxlink connector set. before use! General Information Assembly Guide: OM -BLS Version 2.1 d, 03/2023...
-
Page 4: Table Of Contents
Assembly Instructions BLS Table of contents 1. Safety | Intended use ...................... 5 2. Overview ........................7 Components ......................7 3. Technical specifications ....................8 Data sheet ....................... 8 4. Commissioning ....................... 9 Use of Boxlink connectors A and B ................. 9 System setup with boxlink connector .............. -
Page 5: Safety | Intended Use
The BLS boxlink connector set may only be used by trained and qualified personnel. Personnel must check the BLS for its full suitability before each use. WARNING When visible damage to any part of the BLS boxlink connector set is detected, it must be decommissioned immediately. WARNING... - Page 6 Assembly Instructions BLS The payload of each boxlink (A und B) is designed of 0,5 to [1102 lbs] . Do not exceed this payload! WARNING...
-
Page 7: Overview
Assembly Instructions BLS 2. Overview Components Figure 2.1 - Overview 2x boxlink B - surface KTL-coated as well as colorless-powder-coated 2x boxlink A - surface KTL-coated as well as colorless-powder-coated Captive quick-lock pins... -
Page 8: Technical Specifications
Assembly Instructions BLS 3. Technical specifications Data sheet maximum load capacity per Boxlink: 0,5 to [1102 lbs] (1 to WLL) [2204 lbs] Dimensions (h x w x d) 4x 102 x 26 x 52 mm [4,02 x 1,02 x 2,05 in] Weight Total: 0.85 kg [1,88 lbs]... -
Page 9: Commissioning
Assembly Instructions BLS 4. Commissioning Use of Boxlink connectors A and B Figure 4.1.1 - boxlink connector B und A Two locking pins are fastened to each of connectors A and B. Fasten the boxlink connectors to the product series VERA10, VERA20 and VERA36 with both locking pins. -
Page 10: System Setup With Boxlink Connector
Connect all loudspeakers to each other (front and rear) using the boxlink connector sets. Use WARNING all locking pins of the BLS boxlink connector sets. Also heed chapter 4.1 “Use of boxlink connectors A and B” on page 9. Boxlink A... -
Page 11: System Setup With Curved Loudspeakers
Fasten the VERA S18 or VERA S33 loudspeakers front and rear by means of a BLS boxlink connector set to the associated flying frame. Connect all loudspeakers to each other (front and rear) using the boxlink connector sets. Use all locking pins of the... - Page 12 Assembly Instructions BLS Figure 4.3.2 - Detail: Installation of the rear boxlink connector on the loudspeaker...
- Page 13 Assembly Instructions BLS 1. Fit the first locking pin to the lowest hole of the loudspeaker rigging track. 2. Fasten the second locking pin to the second hole from the top (loudspeaker rigging track) as well as in the slot of the boxlink connector.
-
Page 14: Transport And Storage
Assembly Instructions BLS 5. Transport and Storage Ensure that the surface of the boxlink connector set is not damaged during transport and storage. Moisture may penetrate where steel surfaces are exposed by scratches and result in corrosion. NOTE This is why the product should be transported and stored in a safe, careful, dry and largely dust-free manner. -
Page 15: Ce Declaration Of Conformity
Assembly Instructions BLS 6. CE Declaration of Conformity Copy and translation of the original CE Conformity Declaration: We hereby declare that the below-referenced components by virtue of their design and con- struction, and in the configuration placed on the market by us, satisfy the safety and health requirements of the applicable EC directives. - Page 16 Assembly Instructions BLS TWAMBO GmbH Karl-Hofer-Str. 42 14163 Berlin Germany Phone: + 49 (0) 71 41-48 89 89 0 Fax: + 49 (0) 71 41-48 89 89 99 E-Mail: info@twaudio.de WWW: www.twaudio.de...
Need help?
Do you have a question about the BLS and is the answer not in the manual?
Questions and answers