Table of Contents
Advertisement
Quick Links
Advertisement
Table of Contents
Related Manuals for Eachine TYRO69
Summary of Contents for Eachine TYRO69
- Page 1 TYRO69 QUICK START GUIDE（DIY）...
-
Page 2: Package Include
1x integrated frame with 2.0mm plate thickness and 3D printing camera Mounting base 4X 1104 8600 kV (orange) motors 1X tyro69 20A 4 in1 ESC 1X tyro69 flight controller (main control chip: f411) 1X Caddx beetle V2 camera AIO FPV Transmitter ... -
Page 3: Table Of Contents
TYRO69 Contents Package Include ..................- 1 - 1.1 Frame kit.................... - 1 - 2.1 Motor....................- 1 - 3.1 ESC ..................... - 2 - 4.1 Flight Controller.................- 2 - 5.1 Camera image transmission .............. - 3 - 6.1 Two-bladed propeller................ - 3 - 7.1 Recommended power supply ............ -
Page 4: Frame Kit
TYRO69 1.1 Frame kit Axle Base: 105mm Arm thickness: 2mm Supporting maximum wheelbase: 2.5 inches Spacing of mounting holes for supporting motors: 9mm Material: 3K Carbon Fiber and TPU 3D Printing 2.1 Motor Model: 1104/8600 kV Groove Series: 9N/12P Stator diameter: 11mm Stator Height: 4mm Axis Diameter: 1.5mm... -
Page 5: Esc
TYRO69 3.1 ESC Continuous current: 20A Peak current: 25A (10s) BEC output: none Input voltage: 2-6 s Main Control Chip: EFM8BB21F16G Firmware upgrade: support dshot600/blheli_S/Oneshot125 MOS: 3*3 4.1 Flight Controller Main control chip: stm32f411 IMU: MPU 6000 6 axis sensor... -
Page 6: Camera Image Transmission
TYRO69 Note : Be sure to weld the receiver protocol selection pad 5.1 Camera image transmission Output power: 25 MW Support frequency: 48ch Support TBS Smart Audio Support voltage: 2.9v-5.5v Graphic size: 15mm X14mm Image Sensor: 1/3 "CMOS Sensor" Horizontal Resolution: 1200 TVL... -
Page 7: Two-Bladed Propeller
TYRO69 6.1 Two-bladed propeller Material: Imported PC Installation aperture: 1.5MM Weight: 0.8g/pair Quantity: 10 pairs Color: translucent black/Black/Red/random 7.1 Recommended power supply Recommended voltage: 3S Recommended capacity: 350-450 Mah 8.1 Adjusting parameter (1) Configuration of UART port parameters Enter the Ports item, select the UART port (UART6 in this case), and then select the TBS Smart Audio item (Figure 1) in the Peripheral column to complete the configuration of the flight control image serial port. -
Page 8: Frequency Grouping And Channel Number Configuration
TYRO69 (2) Frequency grouping and channel number configuration Enter OSD parameter menu When VTX1 image transmission, corresponding image transmission receiver display screen and flight control are powered on, the information shown in Figure 2 will appear on the receiving screen. -
Page 9: ② Start Grouping And Channel Configuration
TYRO69 Start grouping and channel configuration Under the OSD MAIN menu, the PITCH rocker can move the cursor arrow up and down to select the menu item, select the FEATURES item, then select the ROLL rocker to the right, and enter the lower configuration menu (Fig. -
Page 10: ③ Output Power Configuration
TYRO69 Figure 6 Grouping and channel configuration validation Output power configuration As in the previous section, the POWER item can be entered by remote control selection, and the required transmission power can be selected (Fig. 7). VTX1 currently supports only 25 mW power options, while the POWER menu with OSD parameters has four options: 25 mW, 200 mW, 500 mW and 800 mW. -
Page 11: ④ Channel Number Indication
TYRO69 Channel number indication The LED lamp displays the set grouping and channel, and the corresponding working frequency is shown in the table below. BAND 5865M 5845M 5825M 5805 M 5785 M 5765 M 5745 M 5725 M A（BOSCAM） 5733 M...