Subscribe to Our Youtube Channel
Related Manuals for Hayter 48 PRO Autodrive FS
Summary of Contents for Hayter 48 PRO Autodrive FS
- Page 1 Harrier 48 PRO Autodrive FS CODE479B OPERATOR MANUAL Original Version (EN) From Serial Number: 406000000 and Up Issued: 12/11/2019 Part number: 3437-134 Rev A...
-
Page 3: Table Of Contents
CONTENTS Introduction Before Operation continued Non Grassed Areas Safety 6 - 9 Controls General Safety Before Mowing Safety Alert Symbol During Operation 15 - 17 Before Operation Safety Starting - General Safety Forward Travel - Fuel Safety Shutting off the Engine During Operation Safety Parking - General Safety... - Page 4 CONTENTS Maintenance continued Rear Deflector Carburettor Adjustments Blade Brake Test Lubrication Storage Storage Safety Preparing the Mower for Storage Storage Removing the Mower from Storage Trouble Shooting Warranty EU Privacy Statement Notes 29 - 32...
-
Page 5: Introduction
For engine details related to your product, please refer to the engine handbook provided. Hayter Limited have designed and tested this machine for reasonably safe service; however, failure to comply with the instructions in this manual may result in personal injury. -
Page 6: Safety
SAFETY Before Operation Safety - Fuel Safety personal injury or death. General Safety You can find additional safety information where This mower has been designed in accordance with EN needed throughout this manual. ISO 5395-2:2017. Fuel is extremely flammable and highly explosive. A fire or explosion from fuel can burn you and others Safety Alert Symbol This product is capable of amputating hands and... -
Page 7: During Operation Safety
3 seconds. If it doesn’t, stop using your mower immediately and contact a • Operate the engine only in well-ventilated areas. Hayter Authorised Service Dealer. Exhaust fumes contain carbon monoxide, which is lethal if inhaled. • Keep bystanders out of the operating area. Keep small children out of the operating area and under •... -
Page 8: After Operation Safety
SAFETY After Operation Safety - General Hayter replacement parts and accessories. Replacement parts and accessories made by other Safety manufacturers could be dangerous, and such use could void the product warranty. • Always shut off the machine, wait for all moving parts to stop, and allow the machine to cool before adjusting, servicing, cleaning, or storing it. -
Page 9: Safety & Instructional Decals
Please ensure all Safety Decals are secured on the mower before using the product. If any of the decals are missing or not secure, do not use the mower, contact your local Authorised Hayter Service Dealer for replacements. WARNING: Improper maintenance, use of non-conforming spare parts, or the removal or modification of the safety decals may cause death or serious injury. -
Page 10: Product Overview
PRODUCT OVERVIEW PRODUCT SPECIFICATION Code 479B Model Harrier 48 PRO Autodrive FS Weight (Net) 51.5 kg Length 1587 mm Width 532 mm Height 1039 mm Width of Cut 480 mm Height of Cut 13 - 60 mm Engine Manufacturer Honda... -
Page 11: Setup
Check that the following items have been supplied Fuel Valve correctly. • If a cable is damaged, contact a Hayter Authorised Service Dealer. For safety during transportation the fuel valve is set to Engine Handbook the OFF position. Ensure that it is in the ON position... -
Page 12: Engine Detail
SETUP 6. Insert the dipstick and tighten the cap securely. Engine Detail (Refer fig.6) NOTE: Disconnect the spark plug lead and ensure that IMPORTANT: Running the engine with a low oil level the fuel valve is in the OFF position before performing can cause engine damage. -
Page 13: Before Operation
Authorised Hayter Service Dealer. 3. Remove the dipstick (1) and check the oil level. engine. 111-9367 - Lawn mower Oil SAE 30 Hayter 4. Re-insert the dipstick (1) into the oil fill neck and 111-9368 - Premium Fuel Treatment Hayter tighten the cap securely. -
Page 14: Adjusting The Cutting Height
BEFORE OPERATION height of cut to protect the cutting mechanism. mower blade could become dangerous projectiles. Adjusting the Cutting Height (Refer fig.9) Inspect the area for hidden obstructions which when contacted by the blade could risk health and safety WARNING: The blade is sharp; contacting the blade or result in damage to the mower. -
Page 15: During Operation
If the engine does not start after repeated attempts, (Refer fig.15) To make a wide turn, steer the mower with the handle contact your local Hayter Authorised Service Dealer in the direction required. or go to the Honda website. When the ground drive clutch lever is disengaged, the mower may be pushed. -
Page 16: Engaging The Blade
Hayter Authorised Service Dealer. bag fitted. Refer to Adjusting the Cutting Height. Trim Side Cutting Reduce the height of cut and mow the area again as necessary until the required finish is obtained. -
Page 17: Grass Bag
Good grass collection depends on good air flow ALWAYS replace a damaged blade. Consult your through the grass bag. To empty the grass bag, Authorised Hayter Service Dealer. pour out the grass clippings and shake the grass bag vigorously to clean the airways. -
Page 18: After Operation
6. Turn the water on. If a cable is damaged, contact a Hayter Authorised serious injury. Service Dealer. Start the engine, engage the BBC and run it until... -
Page 19: Maintenance Schedule
MAINTENANCE SCHEDULE Note: Determine the left and right sides of the mower from the normal operating position. Recommended Maintenance Schedule Maintenance Service Interval Maintenance Procedure Before each use or daily Check the engine-oil level. Check the air filter. Clean grass clippings and dirt from under the mower. Check the condition of guards and safety devices. -
Page 20: Maintenance
MAINTENANCE damage the filter and solvents will dissolve the filter. Preparing for Maintenance 1. Remove the air filter cover (1) by unhooking the IMPORTANT: Before tipping the mower to change two upper tabs (2) on top of the air filter cover and the oil or replace the blade, allow the fuel tank to run the two lower tabs (3). -
Page 21: Changing The Engine Oil
MAINTENANCE Changing the Engine Oil Engine oil capacity: 0.40L NOTE: Run the engine a few minutes to warm the 6. Install the cap/dipstick (2) and tighten securely. oil before changing it. Warm oil drains quickly and (Refer to fig.30) completely. Refer to Setup - Engine Oil Specifications to ensure you are using the correct grade of oil. -
Page 22: Servicing The Spark Plug
MAINTENANCE plug if there is apparent wear, or if the insulator Servicing the Spark Plug is cracked or chipped. Clean the spark plug with a wire brush if it is to be reused. Improper maintenance, use of nonconforming replacement components, or the modification of the 4. -
Page 23: Remove & Replace The Blade
If you are uncomfortable performing this procedure or do not have a torque Blade Sharpening wrench, contact a Hayter Authorised Service Dealer. A slightly worn blade may be re-sharpened. Both blade WARNING: The blade is sharp; contacting the blade edges must be sharpened equally to ensure balance. -
Page 24: Clutch Cable Adjustment
60 mm from the handle. you release the BBC control lever, contact a Hayter or modification of the rear deflector may cause death Authorised Service Dealer. -
Page 25: Storage
STORAGE • Disconnect the lead from the spark plug. (Refer fig.41) Storage Safety • Remove the spark plug, add 30 ml (1 fl oz) of Removing the Mower from Storage Always shut off the mower, wait for all moving engine oil through the spark-plug hole, and pull the parts to stop, and allow the mower to cool before engine start cord slowly several times to distribute adjusting, servicing, cleaning, or storing it. -
Page 26: Trouble Shooting
TROUBLE SHOOTING PROBLEM CAUSES CORRECTIVE ACTION PROBLEM CAUSES CORRECTIVE ACTION Engine stop lever released Operate engine stop lever Undulating ground conditions Change direction of travel Engine will not Incorrect oil level Check oil level Blade worn Sharpen blade turn over Uneven cut Obstruction under deck Remove obstruction... -
Page 27: Warranty
The manufacturers of the engine furnish their own warranty and services are provided through their authorised network (Refer to the Engine Manual for the “Engine Warranty Statement”). To qualify for the 2 year warranty, you must have the machine serviced by a Hayter Authorised Service Dealer* within 12 months of the date of purchase. Please note that these services will be charged at a rate agreed between you and the Dealer. -
Page 28: Eu Privacy Statement
To do so, please contact us by email at legal@toro.com. If you have concerns about the way in which Hayter Ltd. has handled your information, we encourage you to raise this directly with us. Please note that European residents have the right to complain to your... -
Page 29: Notes
NOTES NOTES... - Page 30 NOTES NOTES...
- Page 32 Hayter Limited Spellbrook, Bishop’s Stortford, Herts CM23 4BU England Customer Care Helpline: 0800 616 298 www.hayter.co.uk...
Need help?
Do you have a question about the 48 PRO Autodrive FS and is the answer not in the manual?
Questions and answers