JUKI AMS-210EN Series Quick Start Manual page 2

Hide thumbs Also See for AMS-210EN Series:

Instruction manual (133 pages)

Engineer's manual (249 pages)

page of 3

/ 3
Bookmarks

5. Be sure to turn the power off and check to be sure that the machine and motor completely stop before re-

moving the belt cover and V-belt in order to prevent accident caused by abrupt start of the machine or motor.

6. If a servomotor is used with the machine, the motor does not produce noise while the machine is at rest.

Be sure not to forget to turn the power off in order to prevent accident caused by abrupt start of the motor.

7. Never use the machine with the cooling opening of the motor power box shielded in order to prevent fire

accident by overheat.

Lubrication

1. Be sure to use JUKI genuine oil and JUKI genuine grease to the parts to be lubricated.

2. If the oil adheres on your eye or body, be sure to immediately wash it off in order to prevent inflamma-

tion or irritation.

3. If the oil is swallowed unintentionally, be sure to immediately consult a medical doctor in order to pre-

vent diarrhea or vomiting.

Maintenance

1. In prevention of accident caused by unfamiliarity with the machine, repair and adjustment has to be

carried out by a service technician who is thoroughly familiar with the machine within the scope defined

in the instruction manual. Be sure to use JUKI genuine parts when replacing any of the machine parts.

JUKI assumes no responsibility for any accident caused by improper repair or adjustment or the use of

any part other than JUKI genuine one.

2. In prevention of accident caused by unfamiliarity with the machine or electrical-shock accident, be sure

to ask an electrical technician of your company or JUKI or distributor in your area for repair and mainte-

nance (including wiring) of electrical components.

3. When carrying out repair or maintenance of the machine which uses air-driven parts such as an air cyl-

inder, be sure to remove the air supply pipe to expel air remaining in the machine beforehand, in order to

prevent accident caused by abrupt start of the air-driven parts.

4. Be sure to check that screws and nuts are free from looseness after completion of repair, adjustment

and part replacement.

5. Be sure to periodically clean up the machine during its duration of use. Be sure to turn the power off

and verify that the machine and motor stop completely before cleaning the machine in order to prevent

accident caused by abrupt start of the machine or motor.

6. Be sure to turn the power off and verify that the machine and motor stop completely before carrying out

maintenance, inspection or repair of the machine. (For the machine with a clutch motor, the motor will

keep running for a while by inertia even after turning the power off. So, be careful.)

7. If the machine cannot be normally operated after repair or adjustment, immediately stop operation and

contact JUKI or the distributor in your area for repair in order to prevent accident that can result in per-

sonal injury or death.

8. If the fuse has blown, be sure to turn the power off and eliminate the cause of blowing of the fuse and

replace the blown fuse with a new one in order to prevent accident that can result in personal injury or

death.

9. Be sure to periodically clean up the air vent of the fan and inspect the area around the wiring in order to

prevent fire accident of the motor.

Operating environment

1. Be sure to use the machine under the environment which is not affected by strong noise source (electro-

magnetic waves) such as a high-frequency welder in order to prevent accident caused by malfunction of

the machine.

2. Never operate the machine in any place where the voltage fluctuates by more than "rated voltage ±10 %"

in order to prevent accident caused by malfunction of the machine.

3. Be sure to verify that the air-driven device such as an air cylinder operates at the specified air pressure

before using it in order to prevent accident caused by malfunction of the machine.

4. To use the machine with safety, be sure to use it under the environment which satisfies the following

conditions:

Ambient temperature during operation

Relative humidity during operation

5. Dew condensation can occur if bringing the machine suddenly from a cold environment to a warm one.

So, be sure to turn the power on after having waited for a sufficient period of time until there is no sign

of water droplet in order to prevent accident caused by breakage or malfunction of the electrical compo-

nents.

6. Be sure to stop operation when lightning flashes for the sake of safety and remove the power plug in

order to prevent accident caused by breakage or malfunction of the electrical components.

7. Depending on the radio wave signal condition, the machine may generate noise in the TV or radio. If this

occurs, use the TV or radio with kept well away from the machine.

8. In order to ensure the work environment, local laws and regulations in the country where the sewing

machine is installed shall be followed.

In the case the noise control is necessary, an ear protector or other protective gear should be worn ac-

cording to the applicable laws and regulations.

9. Disposal of products and packages and treatment of used lubricating oil should be carried out properly

according to the relevant laws of the country in which the sewing machine is used.

Safety devices and warning labels(AMS-210EN/IP-420)

Thread take-up lever cover

Warning label

This is a cover for preventing con-

The label gives the

tact between the human body and

minimum precau-

the thread take-up lever.

tions to be taken

when operating the

sewing machine.

Warning label

against pinching

This label warns

that fingers or

other parts of

human body can

be pinched in the

thread take-up le-

ver. (Only for the

sewing machine

provided with a

slide thread take-

up lever)

Finger guard

This is a cover for preventing

contact between fingers and

the needle.

Eye protection cover

This is a cover for pro-

tecting eyes from being

injured by a broken

needle.

Warning label against pinching

Watch-your-head label

The purpose of this label is to

warn the operator to be careful

This label indicates that there is a

to prevent pinching of the human

risk of contact between the sewing

body in the presser foot and re-

machine and the head. (This label

lated parts. (Adhered on the top

is put on the bottom surface of the

face of the feeding frame)

throat plate auxiliary cover.)

In addition, be aware that the safety devices such as the "eye protection cover" and

"finger guard" are sometimes omitted in the sketches, illustrations and figures in-

cluded in the Instruction Manual for the explanation's sake. In the practical use, never

remove those safety devices.

5°C to 35°C

35 % to 85 %

iv iv

(Refer

Warning label against

to the

pinching

Motor cover

warning

This label indicates that

label on

This is a cover for

there is a risk of pinch-

page i.)

preventing contact

ing hands between the

between the motor,

sewing machine and the

gear, fan and pulley

feed mechanism.

and the human body.

Warning label against

pinching

This label indicates that

there is a risk of pinching

hands between the sew-

ing machine and the feed

mechanism. (One each

on the right and left)

Warning label against

pinching

This label indicates that

there is a risk of contact

between fingers and the

needle and intermediate

presser.

Warning label against

pinching

This label warns that

hands can be pinched un-

der the sewing machine.

Power switch

This switch is used for dis-

connecting the power unit

of the sewing machine from

the power supply. It is also

used as the emergency stop

switch.

Electrical-shock danger label

In order to protect against

electrical shock, safety

precautions to be taken to

avoid danger are written

on this label.

CAUTION

Precautions to be taken so as to use the AMS-210EN Series more safely

1. To prevent possible accidents due to electric shocks, neither open the cover of motor electri-

cal box nor touch the component(s) inside the electrical box.

2. Make sure of the needle entry after changing the pattern. Should the pattern protrude from

the work clamp check, needle interferes with the work clamp check resulting in the danger

of occurrence of needle breakage or the like. In addition, check that the work clamp check

which has been set corresponds to that which has been installed on the sewing machine.

1. In case nothing is displayed in the operation panel even when the power switch is turned ON,

turn OFF the power switch and check the power voltage and phase.

2. In order to protect against personal injury, never place your fingers inside the thread take-up lever,

work clamp, work clamp mechanical section and thread take-up lever cover and near the under-

side of the thread trimmer and needle when turning ON the power switch and while the sewing

machine is in operation.

3. To protect against possible accidents due to abrupt startup of the machine, turn OFF the power

switch before tilting the machine head or removing the motor cover.

4. So as to prevent possible accidents caused by abrupt start of the sewing machine, depress

the start switch after ascertaining that there is no interfering thing under the needle when

winding the bobbin thread. In addition, do not allow hair to be close to the bobbin winder

while it is in operation.

5. Feeding frame automatically comes down when pattern is changed, ready key is ON, Presser

switch is ON, intermediate presser button is ON and bobbin winder button is ON. To prevent

possible accidents caused by abrupt start of the sewing machine, never place your fingers

under the feeding frame.

6. To avoid personal injury, never bring your fingers, hair or clothing close to V belt, cloth cut-

ting knife or motor during operation, and never place anything on any of these parts.

7. To avoid personal injury, never operate the machine with the motor cover, eye protection cov-

er, or any other safety devices removed.

8. To prevent personal injury or death, do not operate the sewing machine with its covers removed.

9. The operation panel displays safety warnings. It is necessary therefore to first verify normal

display on the panel when the power switch is turned on, before operating the sewing machine.

10. To prevent personal injury or death, do not press the hand pulley while the sewing machine

is in operation.

11. To avoid personal injury, be careful never to allow your fingers to go inside the machine

when tilting or raising the machine head.

12. To prevent possible accidents due to electric shocks or damaged electrical component(s),

always turn OFF the power switch before connecting or disconnecting the power plug.

13. During thunder and lightning storms, stop your work and disconnect the power from the out-

let to ensure safety and prevent possible accidents due to damaged electrical component(s).

14. If the machine is suddenly moved from a cold place to a warm place, dew condensation may

result. If this occurs, be sure to confirm that there are no potentially dangerous water drops

in the machine before turning it on in order to prevent possible accidents due to damaged

electrical component(s).

15. In the event of a power failure, be sure to turn OFF the power to the machine to protect

against damaged electrical components.

16. When the sewing machine is used without a break for many hours, the temperature of a part of the

machine body or the rear side of operation panel rises higher by 15˚C than the environmental tem-

perature, and you may feel the heat from the part. However, this phenomenon is not abnormal, and

does not affect the components or the like.

17. Do not lubricate the machine oil to the places other than the oil tank and the hook section.

The grease lubricating system except the hook section is employed for this sewing machine,

and the grease flows out when lubricating the machine oil resulting in worn-out of the com-

ponents.

18. Be careful of handling this product so as not to pour water or oil, shock by dropping, and the

like since this product is a precision instrument.

19. In a domestic environment this product may cause radio interference, in which case the user may

be required to make corrective actions.

20. In order to prevent possible accidents due to a ground fault or a dielectric voltage, an appropriate

power plug should be installed by a person who has expertise in electricity. In addition, the power

plug should be connected to the receptacle which is properly grounded without exceptions.

21. In order to prevent possible accidents due to a ground fault, the earth cable should be properly grounded.

"CompactFlash(TM)" is the registered trademark of SanDisk Corporation, U.S.A.

Precautions to be taken so as to use the AMS-210ENHL2210/TF10S more safely