UEi C165 Quick Start Manual

FRESH
AIR
PURGE
GETTING STARTED
TIME 60
Flue 2
Flue1 Com Test
Aux Prs/Temp
Status Exch Test
Menu Room CO
C165
Press "Power" in fresh air and allow to count-
down for Fresh Air purge.
BASIC CO/COMBUSTION ANALYSIS
Insert Flue probe into stack.
Adjust cone so end of the probe is
approximately at the center of the
stack.
NOTE: You will have to drill a hole
at least 3/8". Use appropriate
sealing method after testing.
PRS/TEMP
DIFFERENTIAL TEMPERATURE TEST
PRESS
TO
ZERO
Flue 2
Flue1 Com Test
Aux Prs/Temp
Status Exch Test
Menu Room CO
C165
Rotate the selector dial to
Press
Pressure/Temperature.
(0) pressure sensor.
All manuals and user guides at all-guides.com
C165 Q
NAT GAS
C02
O2
EfG O2++%
Tf
Ta
Flue1
Aux
Status
Menu
Rotate selector dial to Flue 1. In fresh air, O 2
reading should be 20.9% ±0.3%.
Rotate selector dial to Flue 2. In fresh air, CO reading
should be zero (0).
NAT GAS
C02 8.3%
O2 20.9%
EfG O2++%
Tf 42.4%
Ta 0.03m
Flue 2
Flue1 Com Test
Aux Prs/Temp
Status Exch Test
Menu Room CO
C165
Rotate selector dial to Flue 1 for:
CO 2 , O 2 , Gross efficiency, Flue
temperature, Inlet temperature.
Fuel type can be changed via
MENU or STATUS setting
PRS/TEMP
PRESS
TO
ZERO
T2
P1
Flue 2
Flue1 Com Test
Aux Prs/Temp
Status Exch Test
Menu Room CO
C165
Connect probe to T1.
"Pump" to ZERO
Connect probe to T2.
Compatible with any K-Type
thermocouple probe or clamp.
S G
uiCk tart
8.3%
20.9%
42.4%
0.03m
Flue 2
Com Test
Prs/Temp
Exch Test
Room CO
C165
Connect the flue probe thermocouple connector to T1.
Connect flue probe to water trap.
Connect optional probe to T2.
NAT GAS
CO 80P
COa 80P
LOSS O2++%
XAIR O2++%
PRS 0.00i
Flue 2
Flue1 Com Test
Aux Prs/Temp
Status Exch Test
Menu Room CO
C165
Rotate selector dial to Flue 2 for:
CO (ppm), Losses calculated, Excess
air %, pressure reading
Fuel type can be changed via
MENU or STATUS setting.
Make any adjustments as needed for
proper combustion and wait for ana-
lyzer to display change in readings.
(Repeat as necessary).
PRS 0.04i
i=
T1
T1 167,1F
P2
T2 104.3F
T
Flue1
Aux
Status
Menu
Connect thermocouples in
test location to start testing
C165
Observe T1, T2 and
differential (Delta T).
uide
T2 T1
P1 P2
FRESH AIR
PURGE
TURN
OFF
TIME 5
Flue 2
Flue1 Com Test
Aux Prs/Temp
Status Exch Test
Once complete, remove probe from
Menu Room CO
stack, allow analyzer to purge in
fresh air until CO sensor readings
C165
return to ZERO (0) and O 2 readings
reading return to 0% to 21%.
Continue to the next test or power
analyzer off by pressing On/Off, if
finished.
NOTE: Print and store functions may
be used at any time during testing.
PRS 0.04i
i= inH20
T1 167,1F
T2 104.3F
inH20
T 62.8F
62.8F
Flue 2
Flue1
Aux
Status
Menu
Flue 2
Com Test
Prs/Temp
Exch Test
C165
Room CO
Press "Print" to print
results.
Press and Hold
results.
Com Test
Prs/Temp
Exch Test
Room CO
to log