Advertisement
Package Contents:
PARTS
(2) CROSS BARS
(4) C600 LEGS
(4) C600 HINGE ASSEMBLIES
(4) LOAD SECURE POSTS
HARDWARE KIT
(4) 3/8"-16 NUTS
(4) 3/8" SPLIT LOCK WASHERS
(4) 3/8"-16 x 1-1/2" HEX BOLTS
(16) 5/16"-18 x 1" HEX BOLTS
(16) 5/16"-18 SQUARE NUTS
(32) 5/16" SPLIT LOCK WASHERS
(8) 5/16"-18 x 1" CARRIAGE BOLTS
(8) 5/16"-18 x 1-1/2" HEX BOLTS
(8) SPACERS
Before you begin:
Rack fits both straight and angled caps.
Remove all components from the shipping carton.
The rack should be assembled on a padded surface such as carpet to prevent scratching of aluminum surfaces. Remove bands securing
components together.
Read the instructions thoroughly to familiarize yourself with the assembly sequence.
Note that you DO NOT tighten any nuts and bolts until the completed rack is installed on the vehicle unless specified. This allows for minor
adjustments to the rack during the installation process.
Gather the following tools used to assemble and install the rack.
9/16" Socket or open end wrench
1/2" Socket or open end wrench
5/16" Drill bit and drill
Pencil or marker
Tape measure
Center punch and hammer (optional)
Level
2x4 Boards
HAULER RACKS, INC.
st
7109 31
Avenue North
Minneapolis, MN 55427-2848
C600 RACK INSTRUCTIONS
P/N C600FULL-1 / C600MINI-1
Page 1 of 6
Toll Free: 1-800-843-5445
Phone: 763-546-5620
Fax: 763-546-0933
WWW.HAULERRACKS.COM
Advertisement
Table of Contents
Related Manuals for Hauler Racks C600
Summary of Contents for Hauler Racks C600
- Page 1 C600 RACK INSTRUCTIONS P/N C600FULL-1 / C600MINI-1 Package Contents: PARTS (2) CROSS BARS (4) C600 LEGS (4) C600 HINGE ASSEMBLIES (4) LOAD SECURE POSTS HARDWARE KIT (4) 3/8”-16 NUTS (4) 3/8” SPLIT LOCK WASHERS (4) 3/8”-16 x 1-1/2” HEX BOLTS (16) 5/16”-18 x 1”...
- Page 2 Using (2) 5/16”-18 x 1” carriage bolts, go through the hinge first then the leg. Loosely secure the leg to the hinge with (2) 5/16” split lock washers and (2) 5/16”-18 nuts. Repeat for remaining hinge assemblies. HAULER RACKS, INC. Page 2 of 6 Toll Free: 1-800-843-5445...
- Page 3 Repeat for other crossbar. Slide in (1) 3/8”-16 x 1-1/2” bolt into the center channel of the crossbar on each end as shown below. Repeat for other crossbar. HAULER RACKS, INC. Page 3 of 6 Toll Free: 1-800-843-5445 7109 31...
- Page 4 The crossbars can be positioned higher if required. Check to make sure the front and rear crossbar assemblies are level with each other. Adjust if needed. HAULER RACKS, INC. Page 4 of 6...
- Page 5 Secure the leg on the inside of the cap using (2) spacers, (2) 5/16” split lock washers and (2) 5/16”-18 nuts. Repeat for other legs. Tighten all nuts and bolts. Remove 2 x 4 boards. HAULER RACKS, INC. Page 5 of 6 Toll Free: 1-800-843-5445 7109 31...
- Page 6 The racks have been load tested for the racks capacity to hold loads when not on a vehicle. Hauler Racks, Inc. does not warranty load capacities. As the factory has no way of knowing if the product was properly assembled, installed, used according to instructions, or if loads were secured properly.
Need help?
Do you have a question about the C600 and is the answer not in the manual?
Questions and answers