JVC HR-S9600EK Instructions Manual page 43

LO CATE EDIT -IN PO IN T
7
Find the point on the source
tape from where you want
the edited scene to begin by
pressing
@ #
SH U TTLE ring or the JO G
dial, then press IN / O U T (or
PRO G ).
● The edit-in point is
registered in memory
and appears on the screen.
LO CATE EDIT -O UT PO IN T
8
Find the point where you
want the edited scene to
end by pressing
using the SH U TTLE ring or
the JO G dial, then press
IN / O U T (or PRO G ).
● The edit-out point is
registered in memory
and appears on the
screen.
● The total time of the
edited scenes is displayed
to the right of "(+)".
● Repeat steps
each additional scene.
PREP ARE RECORDIN G DECK
9
Engage its Record-Standby mode.
ST ART R.A. EDIT
10
Press START (or O K ).
● Automatic editing begins; all the specified scenes are
copied to the recording deck in the order they were
registered.
● The on-screen display remains while your recorder
searches for each scene (blinking cursor indicates
scene currently being searched for), but disappears
during actual editing.
● While your recorder is searching for each scene, you
can hear high-speed sound (which is not TimeScan
Audio).
● During scene search, the recording deck automati-
cally enters its Record-Standby mode.
● When all registered scenes have been edited, your
recorder enters the Pause mode, the recording deck
enters its Record-Standby mode, and the cursor blinks
at the next available number.
EN D R.A. EDIT
11
Press M EN U to return to the normal screen, and engage
the Stop mode for your recorder and for the recording
deck.
Downloaded from: https://www.usersmanualguide.com/
= 1
2
3
4
or using the
5
6
7
8
[PROG] =
= 1 0:02:23
2
3
or
@ #
4
5
6
7
8
[PROG] =
= 1 0:02:23
2
3
4
5
6
7 and 8 for
7
8
[PROG] =
N O TES:
● You can also monitor the sound when searching for scenes
you want to edit in steps 7 – 8 . Since you can hear the
soundtrack during selection, you can avoid abrupt or
unnatural sounding scene-to-scene transitions. The sound that
is heard, however, is not TimeScan Audio.
● When editing, there may be a discrepancy of about 2 seconds on
the source tape between the locations you chose as edit-in/-out
points and the locations your recorder recognizes as those points.
0:00:00
● For any scene, the edit-out point must have a counter reading
(+) 0:00:00
that is at least 1 second after the corresponding edit-in point. Any
less than 1 second and the edit-out point will not be registered.
● Since the source recorder prerolls during Random Assemble
Editing, there must be at least 15 seconds worth of recorded
material prior to any edit-in point on the source tape.
● If the search time for an edit-in point exceeds 5 minutes, the
recording deck enters its Stop mode and editing will not take place.
● During steps
registering edit-in and -out points in the R.A. Edit screen, the
characters in the on-screen display may become distorted. This
is normal.
To M a k e Corrections . . .
0:02:23
. . . during step 7 or 8 , you can cancel registered in and out
(+) 0:00:00
points by pressing C.RESET/ CAN CEL (or
control. Each time you press, the preceding point is erased.
0:02:51
● If, for example, you have registered 5 sets of in and out points
and want to reset the first set, you have to press C.RESET/
CAN CEL (or
erased. Reenter them after you've repaired the first set of
points.
0:02:51
M em ory Ca pa city
(+) 0:00:28
Random Assemble Editing shares
memory space with the recorder's
timer. If there are programs
occupied by timer-recording data,
those spaces cannot be used to
register edit-in and -out points —
meaning you won't be able to edit
8 scenes.
● When all 8 programs are full,
"PROGRAM FULL" appears on
the R.A. EDIT screen.
● To cancel a program, see page 20.
RM -V7 0 4 U M ulti-Bra nd R.A. Edit Controller
(N ot provided)
By connecting this controller to your recorder's R.A. EDIT
connector, you can perform Random Assemble Editing in
combination with a second non-J VC video recorder. The controller
is compatible with various major recorder brands. For compatible
systems and availability, please consult your J VC dealer.
AKAI
BLAUPUNKT
FERGUSON
GRUNDIG
HITACHI
N O TE:
Although the RM-V704U is designed to operate the recording
deck, it may not work with some recorders, or may have limited
function capability.
7 and 8 — if you engage the Pause mode while
) on the remote
) until all points after the first set have been
PROGRAM FULL
[MENU] : EXIT
BRAN D LIST
J VC SANYO
MITSUBISHI SELECO
NEC REX
PANASONIC SHARP
PHILIPS SONY
43
0:00:00
(+) 0:00:00
THOMSON
TELEFUNKEN
SABA
NORDMENDE
TOSHIBA