1. Manuals
  2. Brands
  3. Titan Manuals
  4. Cutter
  5. TTBCP33-4
  6. Manual

Titan TTBCP33-4 Manual

Petrol brush cutter (33 cm3)
Hide thumbs

Advertisement

Table of Contents

Petrol Brush
Cutter (33 cm
)
3
TTBCP33-4
EAN : 5059340124315
BX220IM
WARNING: Read the instructions before using the machine.

Advertisement

Table of Contents
loading

Related Manuals for Titan TTBCP33-4

Summary of Contents for Titan TTBCP33-4

  • Page 1 Petrol Brush Cutter (33 cm TTBCP33-4 EAN : 5059340124315 BX220IM WARNING: Read the instructions before using the machine.

  • Page 2: Table Of Contents

    TTBCP33-4 Let’s get started... These instructions are for your safety. Please read through them thoroughly before use and retain them for future reference. Getting Started... Safety information Technical Your machine Before start Quick start more detail... Machine functions Operation Care...

  • Page 3: Safety Information

    Safety information TTBCP33-4 Safety warnings IMPORTANT READ CAREFULLY BEFORE USE KEEP FOR FUTURE REFERENCE 1. This machine is not intended for use by children and persons with reduced physical, sensory or mental capabilities, or lack of experience and knowledge. 2. Children should be supervised to ensure that they do not play with the machine.
  • Page 4 Safety information TTBCP33-4 10. Keep bystanders and animals at least 15 metres out of the work area. 11. Do not operate the machine if it has faulty safety equipment or damaged parts. serious personal injury or death. 13. All machines servicing and maintenance, other than the items listed in this manual, should be performed by an authorised service centre.
  • Page 5 Safety information TTBCP33-4 4. Keep handles dry, clean and free from oil and grease. Greasy, oily handles are slippery and may cause loss of control. or medication. 6. When the machine is switched off, make sure the cutting attachment has stopped before setting down the machine.
  • Page 6 Safety information TTBCP33-4 Fuel handling 1. Always switch the machine off, disconnect the spark plug connector and let the machine cool down before refuelling it. 3. Do not smoke while operating the machine, handling fuel or near fuel. the machine or its exhaust system. There is a risk of ignition. Remove spilled fuel carefully from all parts of the machine.
  • Page 7 Safety information TTBCP33-4 3. Allow the engine to cool before storing in any enclosure. 4. Never store the machine with petrol in the tank inside a building where fumes can 5. Store the machine and fuel so that there is no risk of leakages or fumes coming relays/switches, boilers etc.
  • Page 8 Safety information TTBCP33-4 Residual risks Even if you are operating this machine in accordance with all the safety requirements, potential risks of injury and damage remain. The following dangers can arise in connection with the structure and design of this machine: 1.
  • Page 9 Safety information TTBCP33-4 Description of signal words: The signal word that indicates a hazard with a high level of risk DANGER! which, if not avoided, will result in death or serious injury. The signal word that indicates a hazard with a medium level of WARNING! risk which, if not avoided, could result in death or serious injury.
  • Page 10 Safety information TTBCP33-4 Petrol engines produce toxic carbon monoxide exhaust fumes. Breathing 40:1 carbon monoxide can cause nausea, fainting or even death. Do not operate the engine indoors! Stop the engine before refuelling. Never refuel the machine while the engine is running.

  • Page 11: Technical

    TTBCP33-4 Designation of the tool TTBCP33-4 (TT_Brand Name; BCP_Brush Cutter Petrol; 33_Engine size in cc) The machine complies with the applicable European directives and an evaluation method of conformity for these directives was done. General > Dimensions: approx. 185 x 64.5 x 48.5 cm >...
  • Page 12 TTBCP33-4 Sound emission level Equivalent sound pressure level at operator position determined in accordance with ISO 22868 Brush cutter L > 98.2 dB(A) pA av > Grass trimmer L 93.2 dB(A) pA av > uncertainty: 3.0 dB(A) Sound power level determined in accordance with ISO 22868 and Directive 2000/14/EC >...

  • Page 13: Your Machine

    Your machine TTBCP33-4 Tri-arc blade String trimmer head...

  • Page 14: Before You Start

    Your machine / Before you start TTBCP33-4 1. Power unit 18. Tube clamp 2. Spark plug connector 19. Lock pin 3. Ventilation openings 20. Wing knob 4. Recoil starter handle 21. Bottom drive shaft tube 5. Fuel tank cap 22. Gear head 6.
  • Page 15 Before you start TTBCP33-4 WARNING! The machine and the packaging are not children’s toys! Children must not play with plastic bags, sheets and small parts! There is a danger of choking and suffocation! You will need (items not supplied) (items supplied) >...
  • Page 16 Before you start TTBCP33-4 Assembling the U-handle 1. Attach the U-handle (10) onto the handle connector (11) making sure to align the pin on the U-handle with the hole on the connector (Fig. 1). knob (12) clockwise to secure the U-handle (10) in position.
  • Page 17 Before you start TTBCP33-4 2. Loosen the three pre-assembled screws on the gear head (22), using the multi-tool II (35) (Fig. 3). (28), turn the securing nut (29) clockwise to loosen it. 4. Remove the securing nut (27) from the gear head (22).
  • Page 18 Before you start TTBCP33-4 (27) onto the spindle (26) (Fig. 5). (27) until one of its grooves is aligned with one of those on the gear head (22). 8. Insert the multi-tool II (35) into the groove to lock the rotation of the spindle (26).
  • Page 19 Before you start TTBCP33-4 (27) onto the spindle (26) (Fig. 8). (27) until one of its grooves is aligned with one of those on the gear head (22). 7. Insert the multi-tool II (35) into the groove to lock the rotation of the spindle (26).
  • Page 20 Before you start TTBCP33-4 Assembling the bottom drive shaft tube 1. Pull out the lock pin (19) on the tube clamp (18). Insert the bottom drive shaft tube (21) into the upper drive shaft tube (17) (Fig. 9). 2. Release the lock pin (19). Rotate...
  • Page 21 Before you start TTBCP33-4 Filling up fuel and oil WARNING! This machine is not supplied with petrol-oil mixture in the engine! This machine is equipped with a 2-stroke engine. The fuel and oil tank are combined WARNING! NOTE: the fuel mixing bottle (37) and the fuel tank (6).
  • Page 22 Before you start TTBCP33-4 4. Unscrew and remove the fuel tank cap (5) (Fig. 10). 5. Fill the fuel into the fuel tank (6). Leave approximately 5 mm of space between the top of the fuel and the inside edge of the tank to allow for expansion. Do not (Fig.

  • Page 23: Quick Start

    Quick start TTBCP33-4 Operating controls Recoil starter handle Throttle trigger CLOSE lockout OPEN Throttle trigger Choke lever Stop switch Primer...
  • Page 24 Quick start TTBCP33-4 Preparation Add fuel and oil Assemble mixture Starting cold engine Set stop switch Set the choke Press primer Pull recoil Set the choke to I to CLOSE 6 times starter handle to OPEN 4 times (if engine already...
  • Page 25 Quick start TTBCP33-4 Starting warm engine Set stop switch Set the choke Pull recoil Press and Operate to I to OPEN starter handle release the until engine throttle lockout starts and throttle trigger to let engine run at idle Stopping...

  • Page 26: In More Detail

    Machine function TTBCP33-4 Intended use This petrol brush cutter TTBCP33-4 is designated with a maximum power output of 1.0 kW. > With the tri-arc blade and cutting-attachment guard attached, the machine is intended to cut heavier weeds, brush and similar vegetation with a thickness of up to 20 mm.
  • Page 27 Machine function TTBCP33-4 Harness NOTE: The harness improves working movement and enables the operator to manage the job in a safer way and takes the strain away from the body. Always wear the harness when working with the machine. Always turn the machine off and wait until the cutting attachment stops completely before taking off the harness.

  • Page 28: Operation

    Machine function / Operation TTBCP33-4 Throttle trigger lockout The throttle trigger lockout (14) prevents unintentional start of the throttle trigger (16). The throttle trigger can only be activated if the throttle trigger lockout is pressed (Fig. 15). Press and release the throttle trigger lockout (14) and the throttle trigger (16) will set the engine running at idle speed.
  • Page 29 Operation TTBCP33-4 NOTE: special days machines are allowed to be used and what restrictions apply! Ask your community for detailed information and observe the regulations in order to preserve a peaceful neighbourhood and avoid committing administrative offenses! Starting the engine >...
  • Page 30 Operation TTBCP33-4 Starting cold engine touch ground or any objects. Set stop switch (15) to I (Fig. 16). 2. Set the choke (8) to CLOSE position (Fig. 17). 18). 4. Hold the machine securely to the ground with your left hand. Pull the recoil starter handle (4) slowly with your right hand until you feel a strong pull.
  • Page 31 Operation TTBCP33-4 3. Hold the machine securely to the ground with your left hand. Pull the recoil starter give it a brisk, strong pull. Repeat until the engine starts (Fig. 19). 4. Press and release the throttle lockout (14) and throttle trigger (16) to let engine run at idle speed.
  • Page 32 Operation TTBCP33-4 Trimmer line feeding The string trimmer head (23) is equipped with a bumper help to feed the cutting line (32). release fresh trimming line. A cutting line cutter (31) is integrated with the trimming guard (30) and it cuts the line to necessary length (Fig. 22).
  • Page 33 Operation TTBCP33-4 > Do not lift the cutting attachment higher than your hip. The higher you hold the cutting attachment, the higher the risk of objects being thrown (Fig. 23). Max. height: 300 mm > Avoid cutting tall grass in one cut. Trim taller grass in stages (Fig. 24).

  • Page 34: Care And Maintenance

    Operation / Care and maintenance TTBCP33-4 > Hold the cutting attachment just above the ground at an angle of approximately 30° (Fig. 25). > Move the machine with slow and regular motion from left to right before moving it back to the starting position and trimming the next area (Fig. 26).
  • Page 35 Care and maintenance TTBCP33-4 DANGER! Proper maintenance is essential for safe and trouble free operation. Improper maintenance, or failure to address a problem instantly can cause a malfunction which can result in serious injury or even death. 1. Keep the machine clean. Remove debris after each use and before storage.
  • Page 36 Care and maintenance TTBCP33-4 Maintenance table Inspect and maintain this machine regularly based on below maintenance table. Keep the machine in good working condition during maintenance. Part Task Before/after Every 10 hours Every 25 hours each use of operation of operation...
  • Page 37 Care and maintenance TTBCP33-4 3. Form a loop at the middle of the line and insert this loop into the hook on the spool (Fig. 29). 5. Place the spool into the spool assembly and pass each end of the cutting line through the respective holes.
  • Page 38 Care and maintenance TTBCP33-4 replace it with a new one if necessary. case (9) and open its cover (Fig. 31). 2. Remove the filter and tap it on a stable surface to remove dust. Use compressed air (max. 3 bar) to remove stubborn dust.
  • Page 39 Care and maintenance TTBCP33-4 6. Check the spark plug gap. It should be 0.6-0.7 mm (Fig. 32). 7. Replace with a new spark plug if either the electrode or the insulation is damaged. with the multi-tool I (34). NOTE: Do not over tighten the spark plug to avoid any damage! (2).
  • Page 40 Care and maintenance TTBCP33-4 Spare parts/Replacement parts The following parts of this machine may be replaced by the consumer. Spare parts are available at an authorised dealer or through our customer service. Description Cutting blade Tri-arc blade: 3 teeth, Ø255 x Ø25.4 mm Cutting line Ø3.0 mm nylon line...
  • Page 41 Care and maintenance TTBCP33-4 Short term storage (less than 1 day) 1. Let the machine cool down before storage. 2. Store the machine as horizontally as possible. Make sure that no fuel-oil mixture can run out of the carburetor. Long term storage NOTE: Risk of machine damage! >...

  • Page 42: Troubleshooting

    TTBCP33-4 Troubleshooting Troubleshooting Therefore check the machine using this section. In most cases, the problem can be solved quickly. WARNING! Only perform the steps described in these instructions! All further inspection, maintenance and repair work must be performed by an authorised...

  • Page 43: Recycling And Disposal

    Troubleshooting / Recycling and disposal TTBCP33-4 Problem Possible cause Solution Engine does not start Spark plug defective? Replace spark plug. Engine cold? Follow cold starting procedure. Carburetor setting not correct? the carburetor. Engine does not reach Incorrect fuel or incorrect...

  • Page 44: Guarantee

    Your power tool comes with a 2-year guarantee. Should it develop a fault within this period please do not return it to Store. Please contact the Titan 2 Stroke Helpline Guarantee This product carries a guarantee of 2 year.

  • Page 45: Ec Declaration Of Conformity

    EC declaration of conformity TTBCP33-4 (EN) EU DECLARATION OF CONFORMITY (FR) DÉCLARATION UE DE CONFORMITÉ (PL) DEKLARACJA ZGODNOŚCI UE (RO) DECLARAȚIA DE CONFORMITATE UE (ES) DECLARACIÓN UE DE CONFORMIDAD (PT) DECLARAÇÃO DE CONFORMIDADE UE Product/ Produit/ Produkt/Produsul/Producto/Produto > de mato >...
  • Page 46 EC declaration of conformity TTBCP33-4 The object of the declaration described above is in conformity with the relevant Union harmonisation legislation: L’objet de la déclaration décrit ci-dessus est conforme à la législation d’harmonisation de l’Union applicable : Wymieniony powyżej przedmiot niniejszej deklaracji jest zgodny z odnośnymi wymaganiami unijnego prawodawstwa harmonizacyjnego: Obiectul declarației descris mai sus este în conformitate cu legislația relevantă...
  • Page 47 EC declaration of conformity TTBCP33-4 Measured Sound Power Level/ Niveau de puissance acoustique mesuré/ Zmierzony poziom mocy akustycznej/ Nivel de putere acustică măsurat/ Nivel de potencia sonora medido / Nível de potência sonora medido: 107.0 dB(A) Guaranteed Sound Power Level/ Niveau de puissance acoustique garanti/ Gwarantowany poziom mocy akustycznej/ Nivel de putere acustică...
  • Page 48 EC declaration of conformity TTBCP33-4 (UK) DECLARATION OF CONFORMITY Product • Brush cutter • TTBCP33-4 • 33 cm³ , 1.0 kW • 000001 - 999999 Name and address of the manufacturer or his authorised representative: Kingfisher International Products Limited 3 Sheldon Square...
  • Page 49 Manufacturer, Fabricant, Prodecent, Producător, Fabricante: UK Manufacturer: 3 Sheldon Square London W2 6PX United Kingdom EU Manufacturer: Rapenburgerstraat 175E 1011 VM Amsterdam The Netherlands www.diy.com To view instruction manuals online,...

This manual is also suitable for:

5059340124315

Table of Contents