Related Manuals for Titan TTB336TCB
Summary of Contents for Titan TTB336TCB
- Page 1 SAFETY AND OPERATING MANUAL Original instructions TITAN TILE CUTTER 500W TTB336TCB...
- Page 3 This guarantee does not affect your statutory rights. This guarantee is only valid in the UK. For further technical advice, spare parts or repair service (outside of guarantee) please contact your retailer quoting your Titan model number. TITAN TILE CUTTER 500W TTB336TCB...
-
Page 4: General Safety Instructions
GENERAL SAFETY INSTRUCTIONS WARNING! Read all instructions Failure to follow all instructions listed below may result in electric shock, fire and/or serious injury. The term "power tool" in all of the warnings listed below refers to yourmains operated (corded) power tool or battery operated (cordless) power tool. SAVE THESE INSTRUCTIONS keep work area clear. - Page 5 - Never use blades on this machine. - Use only diamond discs for which the maximum possible speed is not less than TITAN TILE CUTTER 500W TTB336TCB...
- Page 6 the maximum spindle speed of the tool and the material to be cut. - Faults in the machine, including guards or diamond discs, should be reported as soon as they are discovered. Never use the machine without the guard in position. - Maximum size of working piece should be 1m².
- Page 7 Wear eye protection. Wear respiratory protection. WARNING – To reduce the risk of injury,user must read instruction manual. Conforms to relevant safety standards Caution, risk of cuttin Use only non fragmented discs Hand protection shall be worn TITAN TILE CUTTER 500W TTB336TCB...
- Page 8 1. Protective guard 2. Mitre cutting guide 3. Parallel guide securing knob 4. On/Off switch 5. Diamond disc 6. Transportation handle (not shown) 7. 45° vertical fence 8. Water reservoir plug...
-
Page 9: Technical Data
Maximum cutting depth 20mm NOISE A weighted sound pressure LpA 95.6dB(A) A weighted sound power: LwA 106.7db(A) Uncertainty 3dB(A) The sound intensity level for the operator may exceed 85dB(A) and sound protection measures are necessary. TITAN TILE CUTTER 500W TTB336TCB... - Page 10 ACCESSORIES The tile cutter is supplied with following accessories: Mitre cutting guide Parallel guide 45° vertical fence Blade Spanners Rubber feet...
- Page 11 (Fig 1). Fig 1 INSTALLATION OF THE DIAMOND DISC AND METAL BRACKET - Unplug the tile cutter from the mains supply. - Remove the cover (45° vertical fence) of the water tank (Fig 2). Fig 2 TITAN TILE CUTTER 500W TTB336TCB...
- Page 12 - Remove the fix screw & washer of blade guard (Fig 3). Fig 3 - Swing the blade guard then lift it out of notch (Fig 4 - 5). - Remove the nut and outer flange from spindle Fig 4 (Fig 6).
- Page 13 - Insert the blade guard into the notch then tighten the screw (Fig 3). Fig 10 - Put cover (45° vertical fence) back into position. Fig 12 Fig 11 TITAN TILE CUTTER 500W TTB336TCB...
- Page 14 INSTALLATION OF THE PROTECTIVE GUARD - Unplug the tile cutter from the mains supply. - Place the guard onto the metal bracket (Fig 13) and fix in place using the screw and washer. Push the black cover cap over the nut (Fig 14). - Cover the diamond disc with the guard.
-
Page 15: Filling The Water Tank
- To switch off the machine, push the red switch marked 0. The tile cutter will now stop. WARNING! The disc will continue to rotate for a few seconds after the machine has been switched off. Wait for the disc to stop before removing TITAN TILE CUTTER 500W TTB336TCB... -
Page 16: Making A Straight Cut
the workpiece or making any adjustments. Stop the machine immediately if there is undue vibration or some other fault. If this situation continues, check the machine to find the origin of the fault. MAKING A STRAIGHT CUT Adjust the parallel guide to the desired width. Use the securing knob to loosen or adjust the guide. -
Page 17: Maintenance
The wire, which is coloured green/ yellow, must be connected to the remaining terminal which is marked with an E or WARNING: Never connect live or neutral wires to the earth terminal of the plug. Only fit an TITAN TILE CUTTER 500W TTB336TCB... -
Page 18: Environmental Protection
approved 13 Amp BS1363/A plug and the correct rated fuse. NOTE: If a moulded plug is fitted and has to be removed take great care in disposing of the plug and severed cable, it must be destroyed to prevent engaging into a socket. ENVIRONMENTAL PROTECTION Waste electrical products should not be disposed of with household waste. -
Page 19: Declaration Of Conformity
Standards and technical specifications referred to: EN61029-1(2009) EN 55014-1(2006) EN55014(1997)+A1(2001)+A2(2008) EN 61000-3-2(2006) EN61000-3-3(2008) Authorised Signatory and technical file holder Date: 14/06/10 Signature: Name: Peter Harries Titan Power Tools (UK)Ltd. Trade House , Mead Avenue ,BA22 8RT Quality Manager 2010 TITAN TILE CUTTER 500W TTB336TCB...