Related Manuals for CAME Ati-S3
Summary of Contents for CAME Ati-S3
- Page 1 CAME.COM/UK Ati-S3 Complete kit for a single swing gate up to 3m wide QUICK SETUP GUIDE Typical gate setup & geometry Gate motor manual release Kit wiring diagram Control panel guide & safety TO BE READ IN CONJUNCTION WITH THE FULL INSTRUCTION MANUAL...
- Page 2 Quick Start Guide Safety Instructions Control Panel: Programming Transmitters Typical Gate Setup Control Panel: Safety Geometry Optional Accessories Manual Release Instructions Kit Wiring Diagram ATI-S3: KIT CONTENTS A3000A ZA3P AF43S Control Panel Radio Frequency Card Motor topd4Fks top-a433n DIR10 Tuned Antenna...
- Page 3 SAFETY INSTRUCTIONS When correctly installed in compliance to installation instructions and adhering to all current electrical, mechanical and manufacturer regulations, your automation system will provide a high degree of safety and problem free operation. Please take note of the following warnings that must be followed in order to prevent accidents during your gate operation: •...
- Page 4 ATI: TYPICAL GATE SETUP OUTSIDE OF GATES INSIDE OF GATES ATI Motor Flashing Light (optional) 2nd set of Photocells (optional) Control Panel Selector Keypad (optional) Mechanical End Stop (not supplied) Reception Antenna Photocells (on outside of gate posts) Photocell column (optional accessory) CONTROL PANEL •...
- Page 5 ATI-S3: GEOMETRY Preliminary checks Tick 1. Check that the gate structure is sturdy enough, the hinges work efficiently and that there is no friction between the fixed and moving parts 2. Make sure that measurement does not exceed the value shown in the reference table 3.
- Page 6 ATI: MANUAL RELEASE The ATI worm drive swing gate operators have a manual release lock beneath a hatch on the top of the motors. To manually release the gates: 1. Raise the door covering the lock 2. Insert the key and turn 180°...
- Page 7 ATI-S3: wiring diagram 12 24 ZA3P Control Panel 0 12 24 FC1 FA2 FC2 AF43S Plug-in TS 10 10 11 3 3P 4 2 C1 CX B1 B2 E E3 TOP-A433N Antenna TX 2 10 2 TX C NC Cable/length RG58 Max.
- Page 8 Safety inputs should now be configured and the gate force tested as required. Please refer to the full manual to complete the commissioning. Should the gates not operate as suggested above, call CAME helpline 0115 921 0430 for technical support.
- Page 9 All previously saved transmitter buttons will be removed from the memory of the control board. FC1 FA2 FC2 10 11 3 3P 4 2 C1 CX B1 B2 3 3P 4 2 C1 CX B1 B2 Should the transmitter not operate as suggested above, call CAME helpline 0115 921 0430 for technical support.
- Page 10 ZA3P: SAFETY SAFETY INPUTS FUNCTIONS > C1 Input, CX Input REOPENING DURING CLOSING • When the automation is in its closing cycle and the safety circuit is triggered the automation will stop and reverse its motion until it reaches its fully open position again.
- Page 11 ATI-S3: ACCESSORIES Code(s) Description RADIO KEYPAD SELECTORS 806SL-0170 SELT1W4G - Surface-mounted, 433.92 MHz radio-frequency keypad selector, 12-keys, with blue backlighting. 25 savable codes and password to access the programming mode. Settable in Rolling Code or Fixed Code mode. RAL7024 Grey colour.
- Page 12 YOU MAY NOT EVEN PARTIALLY REPRODUCE THIS DOCUMENT CAME RESERVES THE RIGHT TO MAKE ANY CHANGES TO THIS DOCUMENT AT ANY TIME THE DATA AND INFORMATION SHOWN IN THIS CATALOGUE ARE SUBJECT TO CHANGE WITHOUT OBLIGATION TO GIVE PRIOR NOTICE BY CAME S.P.A, E&OE CAME S.p.A.