1. Manuals
  2. Brands
  3. Unverferth Manuals
  4. Farm Equipment
  5. Killbros SeedVeyor 102
  6. Manual

Unverferth Killbros SeedVeyor 102 Manual

Bulk seed handling, bulk box carrier
Hide thumbs
Table of Contents

Advertisement

Quick Links

Download this manual
Bulk Seed Handling
SeedVeyor® Bulk Box Carrier
Model 102
Part No. 2000829

Advertisement

Table of Contents
loading
Need help?

Need help?

Do you have a question about the Killbros SeedVeyor 102 and is the answer not in the manual?

Questions and answers

Subscribe to Our Youtube Channel

Related Manuals for Unverferth Killbros SeedVeyor 102

Summary of Contents for Unverferth Killbros SeedVeyor 102

  • Page 1 Bulk Seed Handling SeedVeyor® Bulk Box Carrier Model 102 Part No. 2000829...
  • Page 2 — Introduction SeedVeyor 102 Foreword This symbol identifies important safety messages. When you see it, read the mes- sage that follows and be alert to the possibility of personal injury. Remember, safety instructions stated in this manual are for your protection. Read them carefully and follow them closely when working around or using this machine.
  • Page 3 — Introduction SeedVeyor 102 Product Information All products manufactured by Unverferth Mfg. Co., Inc. are warranted to be free from ma- terial and workmanship defects for one full year from time of consumer delivery. Your local dealer will gladly assist you with any warranty questions.

  • Page 4: Table Of Contents

    — Introduction SeedVeyor 102 Table of Contents Section I Safety General Hazard Information ....................... 1-2 Safety Decals ..........................1-3 Following Safety Instructions ..................... 1-4 Before Servicing ......................... 1-4 Before Operating ........................1-5 During Operation ........................1-5 Before Transporting ........................1-6 During Transport .........................
  • Page 5 — Introduction SeedVeyor 102 Table of Contents Section IV Maintenance Lubrication - Conveyor and Auger Bearings .................. 4-2 Lubrication - Auger U-Joint ......................4-2 Lubrication - Pivot Points ....................... 4-3 Lubrication - Wheel Bearings ......................4-3 Lubrication - Engine Oil Level ....................... 4-3 Conveyor Belt - Belt Tension ......................
  • Page 6 — Introduction SeedVeyor 102 Table of Contents Section V Parts Decals & Touch-Up Paint ......................5-2 Stationary Bracket Components ....................5-4 Scale Components........................5-6 Conveyor Drive Assembly & Hopper Components ..............5-8 Conveyor Idler End Components ....................5-12 Conveyor Discharge End Components ..................5-14 Auger Drive Assembly &...
  • Page 7 — Safety SeedVeyor 102 Section I Safety General Hazard Information ....................... 1-2 Safety Decals ..........................1-3 Following Safety Instructions ..................... 1-4 Before Servicing ......................... 1-4 Before Operating ........................1-5 During Operation ........................1-5 Before Transporting ........................1-6 During Transport ......................... 1-6 Pressurized Oil ...........................

  • Page 8: Safety

    It is true that the designer, the manufacturer, and the safety engineer can help; and they will help, but their combined efforts can be wiped out by a single careless act of the operator. It is said that, “the best kind of a safety device is a careful operator.” We, at Unverferth Mfg.

  • Page 9: Safety Decals

    — Safety SeedVeyor 102 Safety Decals • REPLACE LOST, DAMAGED, PAINTED, OR UNREADABLE DECALS IMMEDIATELY. IF PARTS THAT HAVE DECALS ARE REPLACED, ALSO MAKE SURE TO INSTALL NEW DECALS. THESE DECALS INFORM AND REMIND THE OPERATOR WITH OPERATIONAL INFORMATION AND SAFETY MESSAGES. Part No.

  • Page 10: Following Safety Instructions

    — Safety SeedVeyor 102 Following Safety Instructions • Read and understand this operator’s manual before operating. • All machinery should be operated only by trained and authorized personnel. • To prevent machine damage, use only attachments and service parts ap- proved by the manufacturer.

  • Page 11: Before Operating

    — Safety SeedVeyor 102 Before Operating • Do not stand between the towing vehicle and implement during hitching. • Always make certain everyone and everything is clear of the machine before beginning operation. • Verify that all safety shields are in place and properly secured. •...

  • Page 12: Before Transporting

    — Safety SeedVeyor 102 Before Transporting • Secure transport chains to the towing vehicle before transporting. DO NOT transport without chains. • Install transport locks before transporting. • Check for proper functioning of all available transport lights. Make sure that all reflectors are clean and in place on machine.

  • Page 13: Prepare For Emergencies

    — Safety SeedVeyor 102 Preparing for Emergencies • Keep a first aid kit and properly rated fire extinguisher nearby. • Keep emergency numbers for fire, rescue, and poison control personnel near the phone. Wearing Protective Equipment • Wear clothing and personal protective equipment appropriate for the job. •...
  • Page 14 — Safety SeedVeyor 102 Notes...

  • Page 15: Set Up

    — Set Up SeedVeyor 102 Section II Set Up Pre-Delivery Checklist ........................2-2 SeedVeyor Assembly ........................2-2 Assemble Hitch to Undercarriage ....................2-3 Raising Conveyor/Auger to Working Position .................. 2-4 Optional Scale Package (#26858)....................2-5 Optional Electric Raise/Lower for Conveyor ................... 2-7 Optional AG Decal Package Placement ..................

  • Page 16: Pre-Delivery Checklist

    — Set Up SeedVeyor 102 Pre-Delivery Checklist After the SeedVeyor tender has been completely assembled, use the following checklist and inspect the implement. Check off each item as it is found satisfactory or after proper ad- justment is made. o Torque wheel nuts as specified in Maintenance section. o Torque all axle mounting hardware to 120 ft.-lbs.

  • Page 17: Assemble Hitch To Undercarriage

    — Set Up SeedVeyor 102 Assemble Hitch to Undercarriage 1. If the seed tender was shipped with a hitch installed, torque 5/8”-11UNC retaining hard- ware to 120-135 ft.-lbs. If it was shipped without a hitch installed, proceed to step 2. 2.

  • Page 18: Raising Conveyor/Auger To Working Position

    — Set Up SeedVeyor 102 Raising Conveyor/Auger into Working Position Unit is shipped with the conveyor or auger in the lowered position. If the unit is not equipped with the optional electric lift/lower, it will be necessary to raise the conveyor/auger to the upper fixed position.

  • Page 19: Optional Scale Package (#26858)

    — Set Up SeedVeyor 102 Optional Scale Package (#2000621) 1. Assemble the weigh bars (902063) to the scale FIG. 1 brackets using 3/8” bolts and locknuts. The weigh bars must be assembled so the ‘TOP’ indicator on the weigh bar is located to the bottom of the bracket or rotate the load cell so the “bending direction”...
  • Page 20 — Set Up SeedVeyor 102 Optional Scale Package (#2000621) (continued) 8. Remove the safe lifting device from the center plates on the upper platform. 9. Route the weigh bar cables along the inside edge of the box and fasten using the cable ties (9000106).

  • Page 21: Optional Electric Raise/Lower For Conveyor/Auger

    — Set Up SeedVeyor 102 Optional Electric Raise/Lower for Conveyor/Auger 1. Attach the clevis weldment 2009372CG to the conveyor/auger arm using 3/8” bolts and locknuts. 2. Attach the electric actuator to the support arm and lift link using the clevis pins and cotter pins.

  • Page 22: Optional Ag Decal Package Placement

    — Set Up SeedVeyor 102 Optional AG Decal Package Placement 1. Center and attach the SMV Emblem (95730) to the rear of the unit 8 1/2” from the frame. (FIG. 2-20) 2. Attach the SIS decal (9008714) to the rear of the unit 13 3/4”...
  • Page 23 — Set Up SeedVeyor 102 Optional AG Decal Package Placement (continued) 5. Place the amber reflector (9003127) 4” down on the frame on the right-hand side of the unit. Right-Hand (FIG. 2-22) Side View FIG. 2-22 6. Place the amber reflector (9003127) 4” down Left-Hand on the frame on the left-hand side of the unit.
  • Page 24 — Set Up SeedVeyor 102 Notes 2-10...

  • Page 25: Operation

    — Operation SeedVeyor 102 Section III Operation Preparing Towing Vehicle ........................ 3-2 Preparing Implement - Lubrication ....................3-2 Preparing Implement - Tires/Wheels ....................3-2 Connecting SeedVeyor to Towing Vehicle ..................3-3 Transport Chains ..........................3-3 Transporting ............................. 3-4 Power Pak Warranty.........................3-5 Engine Operation ..........................

  • Page 26: Preparing Towing Vehicle

    — Operation SeedVeyor 102 Preparing Towing Vehicle Before operating the implement, refer to the towing vehicle’s operator’s manual for informa- tion concerning safe methods of operation, hitch capacities, hitch adjustments, tire inflation and undercarriage braking operation. The vehicle must be equipped with proper electric undercarriage braking components. Check the vehicle brakes and transport lights.

  • Page 27: Connecting Seedveyor To Towing Vehicle

    — Operation SeedVeyor 102 Connecting SeedVeyor to Towing Vehicle • DO NOT STAND BETWEEN THE IMPLEMENT AND THE TOWING VEHICLE WHEN HITCHING. The SeedVeyor undercarriage is designed to be connected to a towing vehicle utilizing either the pintle hitch, or a 2 5/16” ball hitch. Back the towing vehicle up to the undercarriage and align the vehicle’s ball or pintle hook with the coupler or ring on the undercarriage.

  • Page 28: Transporting

    — Operation SeedVeyor 102 NOTE: - EXTERIOR DURABILITY: MUST COMFORM TO ASTM D-1014. LIFE EXPECTANCY EQUALS FIVE YEARS. - ADHESIVE: PRESSURE SENSITIVE ADHESIVE BACKING SHALL MEET ADHESIVE SYSTEMS AS SPECIFIED IN ASTM D-4956, CLASS 1 BACKING. Transporting EXPECTANCY EQUALS FIVE YEARS - DECAL FORMAT AND COLORS MUST CONFORM TO ASAE S441.3 - SCORE BACKER / LINER: VERTICAL, HORIZONTAL, OR AS INDICATED.

  • Page 29: Power Pak Warranty

    — Operation SeedVeyor 102 Power Pak Warranty For general maintenance and servicing of power pak unit. NOTE: For maintenance of engine and warranty information, refer to Operator’s Manual pro- vided with engine. Following are phone numbers and Websites for your convenience: www.honda-engines.com Phone 800-426-7701 Canada...

  • Page 30: Engine Operation

    — Operation SeedVeyor 102 Engine Operation • EXPLOSIVE FUEL CAN CAUSE FIRES AND SEVERE BURNS. STOP THE ENGINE BEFORE FILLING THE FUEL TANK. • CARBON MONOXIDE CAN CAUSE SEVERE NAUSEA, FAINTING OR DEATH. DO NOT OPERATE THE ENGINE IN A CLOSED OR CONFINED AREA. •...

  • Page 31: Raising And Lowering Conveyor/Auger

    — Operation SeedVeyor 102 Raising and Lowering Conveyor or Auger If equipped with electric lift/lower, the conveyor/ auger can be raised by first pivoting the con- veyor/auger out of the transport position, and then actuating the raise/lower button on the wired switch.

  • Page 32: Filling Planter Or Drill

    — Operation SeedVeyor 102 Filling Planter or Drill The conveyor/auger On/Off is controlled by a centrifugal clutch on the engine. Increasing the engine speed will engage the clutch and turn the conveyor/auger on. Continuing to increase the engine speed will increase the belt/auger flighting speed. Decreasing the engine speed will slow the belt/auger flighting, and eventually disengage the clutch to turn the conveyor/ auger off.

  • Page 33: Loading Boxes Onto Seedveyor

    — Operation SeedVeyor 102 Loading Boxes Onto SeedVeyor 1. Remove covers from the SeedVeyor box chute by removing the pin holding the Remove Covers cover in place. Place the pin back into the bracket. Cover Removed 2. Locate covers in storage position in front of the front standard, securing with provided Cover in Storage Location bungee cord.

  • Page 34: Electronic Scale Operation - Model 640Xl (Optional)

    — Operation SeedVeyor 102 Electronic Scale Operation - Model 640XL (Optional) The following instructions can also be found in your scale/indicator user’s manual. Key Functions ON/OFF Pressed to power on or off the indicator. Pressed to access memory channel. Also used to increment numbers during the numeric entry procedure.
  • Page 35 — Operation SeedVeyor 102 Electronic Scale Operation - Model 640XL (Optional) (continued) Gross/Tare/Net Weighing (continued) 4. Remove the weighed material from the scale (leaving the tared item). 5. Repeat steps 2 through 5 for each weighment using the same tare weight. 6.
  • Page 36 — Operation SeedVeyor 102 Electronic Scale Operation - Model 640XL (Optional) (continued) How to Configure Filtering (continued) 5. Press the PRINT/SELECT key twice... The current CONSTANT value is shown. Press the HOLD/MENU key to increase the value. Increasing this value causes the indicator to ignore increasing amounts of weight change on the scale.
  • Page 37 Below is a summary of the items in this menu, followed by a comprehensive explanation of each item: • A-LIST Used to edit the memory accumulator descriptions — Operation SeedVeyor 102 • A-STAT Used to access statistics of the memory accumulator channels Electronic Scale Operation - Model 640XL (Optional) (continued) CLR.ACC Use this to clear accumulator channels...
  • Page 38 — Operation SeedVeyor 102 Notes 3-14...
  • Page 39 — Maintenance SeedVeyor 102 Section IV Maintenance Lubrication - Conveyor and Auger Bearings .................. 4-2 Lubrication - Auger U-Joint ......................4-2 Lubrication - Pivot Points ....................... 4-3 Lubrication - Wheel Bearings ......................4-3 Lubrication - Engine Oil Level ....................... 4-3 Conveyor Belt - Belt Tension ......................
  • Page 40 — Maintenance SeedVeyor 102 Lubrication Lubricate with an SAE multi-purpose grease. All fittings must be free from dirt and paint to insure entry of lubricant inside the bearing. Conveyor and Auger Bearings Lubricate these bearings every 100 hours of operation and at the end of each season before storage.

  • Page 41: Lubrication - Pivot Points

    — Maintenance SeedVeyor 102 Lubrication (continued) Pivot Points Lubricate the pivot points on the pivoting arm Shown less conveyor/auger for every 50 hours of operation and at the end of illustration purposes only. each season. Grease Pivot Point Wheel Bearings The wheel bearings should be cleaned, repacked and adjusted every 12 months or 12,000 miles, whichever comes first.
  • Page 42 — Maintenance SeedVeyor 102 Conveyor Belt Proper belt tension and correct ‘tracking’ of the belt are critical to maintaining the belt for years of worry-free use. Belt tension and tracking should be checked at the beginning of each season. Belt alignment should be checked after the very first initial use then after the first 2 hours of initial use or after every adjustment of the belt tension/alignment.
  • Page 43 — Maintenance SeedVeyor 102 Conveyor Belt (continued) Belt Tracking The conveyor belt must always run at the center of the pulley in both the intake and discharge end. Improper tracking of the belt will result in excessive wear to the edge of the belt, and will greatly reduce belt lift.

  • Page 44: Brake Cleaning And Inspection - Magnets

    — Maintenance SeedVeyor 102 Brake Cleaning and Inspection Your undercarriage brakes must be inspected and serviced immediately if a loss of perfor- mance is experienced. With normal use, servicing at one year intervals is usually adequate. With increased usage, this work should be performed more frequently as required. Magnets and shoes must be changed when they become excessively worn or scored, a condition which can reduce vehicle braking.

  • Page 45: Brake Cleaning And Inspection - Magnets

    — Maintenance SeedVeyor 102 Brake Cleaning and Inspection (continued) Shoes and Linings A simple visual inspection of your brake lin- ings will tell if they are usable. Replacement is necessary if the lining is worn (to within 1/16” or less), contaminated with grease or oil, or abnormally scored or gouged.

  • Page 46: How To Measure Amperage

    — Maintenance SeedVeyor 102 How to Measure Amperage System amperage is the current flowing in the system when all the magnets are energized. The amperage will vary in proportion to the voltage. The engine of the tow vehicle should be running with the undercarriage connected when checking the undercarriage braking sys- tem.

  • Page 47: Brake Drum Inspection

    — Maintenance SeedVeyor 102 Brake Drum Inspection There are two areas of the brake drum that are subject to wear and require periodic inspec- tion. These two areas are the drum surface where the brake shoes make contact during stopping and the armature surface where the magnet contacts (only in electric brakes). The drum surface should be inspected for excessive wear or heavy scoring.

  • Page 48: Troubleshooting Brakes

    — Maintenance SeedVeyor 102 Troubleshooting Brakes Most electric brake malfunctions, that cannot be corrected by either brake adjustments or synchronization adjustments, can generally be traced to electrical system failure. Voltmeters and ammeters are essential tools for proper troubleshooting of electric brakes. Mechanical causes are ordinarily obvious, i.e.
  • Page 49 — Maintenance SeedVeyor 102 Belt Stretcher (Optional) ITEM PART NO. DESCRIPTION TA4-114400-0 BELT INSTALLATION TOOL 9390-122 CAPSCREW, 5/8-11UNC x 1 1/2 LG. GRADE 5 TA0-903118-0 BEARING, BALL THRUST, 5/8” I.D. TA1-114401-0 BOTTOM BAR TA2-114404-0 PLAIN TOP BAR WELDMENT TA2-114406-0 THREADED TOP BAR WELDMENT TA2-114408-0 THREAD ROD WELDMENT 4-11...

  • Page 50: Stretcher Assembled To Belt

    — Maintenance SeedVeyor 102 Belt Stretcher (Optional) (Continued) Stretcher Assembled to Belt FOR ILLUSTRATION ONLY Belt Stretcher Assembly Rides On Bottom Of Conveyor Stretcher Trough/Pan And Is Held In Line By Bolts Assembly View "A" Belt Return Access Opening Shield View "B"...

  • Page 51: Wheels & Tires - Wheel Torque Requirements

    — Maintenance SeedVeyor 102 Wheels & Tires Wheel Torque Requirements • IMPROPERLY TORQUED WHEEL NUTS/BOLTS CAN CAUSE A LOSS OF IMPLEMENT CONTROL AND MACHINE DAMAGE. TORQUE WHEEL NUTS/BOLTS TO VALUES IN THE TABLE. CHECK THE TORQUE BEFORE THE INITIAL USE, AFTER ONE HOUR OF UNLOADED USE OR AFTER THE FIRST LOAD, AND EACH LOAD UNTIL THE WHEEL NUTS/BOLTS MAINTAIN THE TORQUE VALUE.
  • Page 52 — Maintenance SeedVeyor 102 Wheels & Tires (continued) Tire Warranty For questions regarding new tire warranty, please contact your local equipment tire dealer. Used tires carry no warranty. The following are phone numbers and websites for your convenience: Greenball www.greenball.com Phone nearest location: California 800-937-5204...

  • Page 53: Torque Chart

    — Maintenance SeedVeyor 102 Torque Chart Capscrews - Grade 5 NOTE: Grade 5 capscrews can be identified by three radial dashes on the head. NOTE: Tighten the U-bolts to have the same number of threads exposed on each end. FOOT NEWTON SIZE POUNDS...

  • Page 54: Storage

    — Maintenance SeedVeyor 102 Storage Your SeedVeyor tender is an important investment. Spend a little time to protect it from de- structive rust and corrosion. You will be repaid in longer service life and better performance. After use, clean out the box, conveyor/auger and hopper. Remove all seed, and pressure wash to remove road dirt, seed treatment, etc.

  • Page 55: Troubleshooting

    — Maintenance SeedVeyor 102 Troubleshooting PROBABLE CAUSE CORRECTION UNDERCARRIAGE SWAYING, TIRE WEAR, LIGHTS Unit sways during travel Check tire pressure Check tongue and steering hardware, tighten appropriately Tires show excessive wear Check tire pressure Wheel makes grinding or squeaking noise Service wheel bearings Tail lights are not functioning Check wires and connections...

  • Page 56: Front Undercarriage Electrical Schematic

    — Maintenance SeedVeyor 102 Front Undercarriage Electrical Schematic #25045 4-18...

  • Page 57: Undercarriage Lighting & Brake Electrical Schematic #25046

    — Maintenance SeedVeyor 102 Undercarriage Lighting & Brake Electrical Schematic #25046 4-19...

  • Page 58: Charge From Truck Electrical Schematic - #29410

    — Maintenance SeedVeyor 102 Charge From Truck Electrical Schematic — #29410 4-20...

  • Page 59: Conveyor Or Auger Control Electrical Schematic - #28920

    — Maintenance SeedVeyor 102 Conveyor/Auger Control Electrical Schematic — #28920 4-21...

  • Page 60: Conveyor Or Auger Control Electrical Schematic - #28920

    — Maintenance SeedVeyor 102 Conveyor/Auger Control Electrical Schematic — #2000588 For Electric Conveyor/Auger Lift Package 4-22...

  • Page 61: Switch Electrical Schematic - #26734

    — Maintenance SeedVeyor 102 Switch Electrical Schematic — #26734 4-23...
  • Page 62 — Maintenance SeedVeyor 102 Switch Electrical Schematic — #2000617 For Electric Conveyor/Auger Lift Package 4-24...
  • Page 63 — Parts SeedVeyor 102 Section V Parts Decals & Touch-Up Paint ......................5-2 Stationary Bracket Components ....................5-4 Scale Components........................5-6 Conveyor Drive Assembly & Hopper Components ..............5-8 Conveyor Idler End Components ....................5-12 Conveyor Discharge End Components ..................5-14 Auger Drive Assembly &...

  • Page 64: Parts

    — Parts SeedVeyor 102 Decals & Touch-Up Paint Please visit www.unverferth.com/parts/ for the most current parts listing. FRONT, LEFT-HAND VIEW Parts Li ITEM 235161 95445 97961 98350 27741@ 902456 9807 9390-028 9500464 91605 902983 902980 9500590 95839 98229 REAR, RIGHT-HAND VIEW...
  • Page 65 — Parts SeedVeyor 102 Decals & Touch-Up Paint Please visit www.unverferth.com/parts/ for the most current parts listing. ITEM PART NO. DESCRIPTION NOTES 235161 Decal, DANGER “Flammable” 95445 Decal, WARNING “High-Pressure Fluid” 97961 Decal, WARNING “Read and Understand” 98350 Decal, WARNING “No Riders”...

  • Page 66: Stationary Bracket Components

    — Parts SeedVeyor 102 Stationary Bracket Components Please visit www.unverferth.com/parts/ for the most current parts listing.
  • Page 67 — Parts SeedVeyor 102 Stationary Bracket Components Please visit www.unverferth.com/parts/ for the most current parts listing. ITEM PART NO. DESCRIPTION NOTES 29070CG Stationary Bracket 9390-138 Capscrew 5/8-11UNC x 7 Grade 5 9801 Locknut 5/8-11UNC...

  • Page 68: Scale Components

    — Parts SeedVeyor 102 Scale Components Please visit www.unverferth.com/parts/ for the most current parts listing.
  • Page 69 — Parts SeedVeyor 102 Scale Components Please visit www.unverferth.com/parts/ for the most current parts listing. ITEM PART NO. DESCRIPTION NOTES 29065CG Scale Bracket Weldment 902063 Weigh Bar - 2 1/8” Dia. w/ 21’ Cable 9390-138 Capscrew 5/8-11UNC x 7 Grade 5...

  • Page 70: Conveyor Drive Assembly & Hopper Components

    — Parts SeedVeyor 102 Conveyor Drive Assembly & Hopper Components Please visit www.unverferth.com/parts/ for the most current parts listing. ITEM 20016 9473 ITEM 29150 90167 28377 29160 90205 9399- 90165 9399- 91263 9405- TA0-9 29157 9388- 91257 91256 90311 9388-...
  • Page 71 — Parts SeedVeyor 102 Conveyor Drive Assembly & Hopper Components Please visit www.unverferth.com/parts/ for the most current parts listing. ITEM PART NO. DESCRIPTION NOTES 29150CG Engine Mount Weldment 901673 Honda Engine 4.8 Net HP Gas, 9.9 Cu. In. 901333 Key/Ignition Replacement...
  • Page 72 — Parts SeedVeyor 102 Conveyor Drive Assembly & Hopper Components (continued) Please visit www.unverferth.com/parts/ for the most current parts listing. ITEM PART NO. DESCRIPTION NOTES 9807 Locknut 5/16-18UNC 2008982 Actuator Replacement Kit 2008983CG Throttle Bracket Angle for Actuator Assembly 26719CG For 6”...
  • Page 73 — Parts SeedVeyor 102 Notes 5-11...

  • Page 74: Conveyor Idler End Components

    — Parts SeedVeyor 102 Conveyor Idler End Components Please visit www.unverferth.com/parts/ for the most current parts listing. 5-12...
  • Page 75 — Parts SeedVeyor 102 Conveyor Idler End Components Please visit www.unverferth.com/parts/ for the most current parts listing. ITEM PART NO. DESCRIPTION NOTES 2005359CG Conveyor Tube 6” x 18’ with Decals Plate/Strap TA0-903088-0 Bearing w/Flange 1” I.D. 23912CG Adjustment Plate 9388-024...

  • Page 76: Conveyor Discharge End Components

    — Parts SeedVeyor 102 Conveyor Discharge End Components Please visit www.unverferth.com/parts/ for the most current parts listing. ITEM 23918@ 23994@ 24260 24414@ 24755 26580@ 901101 901662 901723 902006 91256 93400 9500341 9388-051 9390-055 9394-004 9394-006 9394-010 9404-019 9404-021 9405-076 97189...
  • Page 77 — Parts SeedVeyor 102 Conveyor Discharge End Components Please visit www.unverferth.com/parts/ for the most current parts listing. ITEM PART NO. DESCRIPTION NOTES 9500310 Idler Cover 23918CG Top Shield/Cover 23994CG Adjustment Plate 24260 Seal 24414CG Spout Bracket 24755 Poly Strip 26580CG...

  • Page 78: Auger Drive Assembly & Hopper Components

    — Parts SeedVeyor 102 Auger Drive Assembly & Hopper Components Please visit www.unverferth.com/parts/ for the most current parts listing. 5-16...
  • Page 79 — Parts SeedVeyor 102 Auger Drive Assembly & Hopper Components Please visit www.unverferth.com/parts/ for the most current parts listing. ITEM PART NO. DESCRIPTION NOTES 26734 Switch Assembly 198” 28920 Wire Harness 2000399 Vinyl Cover 26505 Switch Retainer 2005356CG Auger Tube 6” x 18’ with Decals...

  • Page 80: U-Joint, Pulley, Engine, & Battery Components

    — Parts SeedVeyor 102 U-Joint, Pulley, Engine, & Battery Components Please visit www.unverferth.com/parts/ for the most current parts listing. ITEM PART NO. DESCRIPTION NOTES 104988 Draw Latch 2008983CG Throttle Bracket 26719CG Angle for Actuator Assembly 5-18...
  • Page 81 — Parts SeedVeyor 102 U-Joint, Pulley, Engine, & Battery Components Please visit www.unverferth.com/parts/ for the most current parts listing. ITEM PART NO. DESCRIPTION NOTES 28377CG Adjustment Plate 28418B Battery Bracket 28419CG Battery Cover 29157CG Shield Weldment 29160CG Outer Shield Weldment...

  • Page 82: Auger Discharge End Components

    — Parts SeedVeyor 102 Auger Discharge End Components Please visit www.unverferth.com/parts/ for the most current parts listing. 5-20...
  • Page 83 — Parts SeedVeyor 102 Auger Discharge End Components Please visit www.unverferth.com/parts/ for the most current parts listing. ITEM PART NO. DESCRIPTION NOTES TA0-903088-0 Bearing w/Flange 1” I.D. 29405CG End Cap 9473 Self-Drilling Screw 1/4-14 x 3/4 24414CG Spout Bracket 9928...
  • Page 84 — Parts SeedVeyor 102 Pivot Arm Components Please visit www.unverferth.com/parts/ for the most current parts listing. ITEM Front, Left-Hand Side Shown 5-22...

  • Page 85: Pivot Arm Components

    — Parts SeedVeyor 102 Pivot Arm Components Please visit www.unverferth.com/parts/ for the most current parts listing. ITEM PART NO. DESCRIPTION NOTES 9388-052 Carriage Bolt 3/8-16UNC x 1 1/4 Grade 5 91263 Flange Nut 3/8-16UNC 9936 Locknut 1/4-20UNC 24863 Plate/Segment 9388-025...
  • Page 86 — Parts SeedVeyor 102 Pivot Arm Components (continued) Please visit www.unverferth.com/parts/ for the most current parts listing. ITEM PART NO. DESCRIPTION NOTES 9500091 Nylon Washer 9405-086 Flat Washer 1/2” SAE 9663 Top Locknut 1-8”UNC 2000189 Bearing Assembly 23951 Bushing 9405-118 Flat Washer 1”...
  • Page 87 — Parts SeedVeyor 102 Notes 5-25...

  • Page 88: Electric Conveyor Lift Package

    — Parts SeedVeyor 102 Electric Conveyor Lift Package #2000623 Please visit www.unverferth.com/parts/ for the most current parts listing. 5-26...
  • Page 89 — Parts SeedVeyor 102 Electric Conveyor Lift Package #2000623 Please visit www.unverferth.com/parts/ for the most current parts listing. ITEM PART NO. DESCRIPTION QTY. NOTES 903116 Electric Actuator 2009372CG Clevis Weldment 902280 Clevis Pin 1/2” Dia. x 2 5/32 9391-023 Cotter Pin 1/8” Dia. x 1...

  • Page 90: Platform Components

    — Parts SeedVeyor 102 Platform Components Please visit www.unverferth.com/parts/ for the most current parts listing. 5-28...
  • Page 91 — Parts SeedVeyor 102 Platform Components Please visit www.unverferth.com/parts/ for the most current parts listing. ITEM PART NO. DESCRIPTION NOTES 2010229DG Platform Cover =Dove Grey= 27825DG Hopper Weldment =Dove Grey= 27826 Rubber Hopper 91257 Large Flange Hex Nut 5/16”-18UNC 9388-025 Carriage Bolt 5/16”-18UNC x 1”...

  • Page 92: Undercarriage, Hitch & Fender Components

    — Parts SeedVeyor 102 Undercarriage, Hitch & Fender Components Please visit www.unverferth.com/parts/ for the most current parts listing. 5-30...
  • Page 93 — Parts SeedVeyor 102 Undercarriage, Hitch & Fender Components Please visit www.unverferth.com/parts/ for the most current parts listing. ITEM PART NO. DESCRIPTION NOTES 29237CG Fender Step/Mount LH 29238CG Fender Step/Mount RH 29240CG Fender Weldment 900956 Grommet 900954 Light/Amber (Round) 9405-086 Flat Washer 1/2”...
  • Page 94 — Parts SeedVeyor 102 Undercarriage, Hitch & Fender Components (continued) Please visit www.unverferth.com/parts/ for the most current parts listing. PART NO. DESCRIPTION NOTES 900786 Breakaway Electric Switch Complete 902764 Battery w/Charger & Box 29230CG Light Bar Weldment 9390-125 Capscrew 5/8-11UNC x 2 1/4...
  • Page 95 — Parts SeedVeyor 102 Notes 5-33...

  • Page 96: Axle & Wheel Components

    — Parts SeedVeyor 102 Axle & Wheel Components Please visit www.unverferth.com/parts/ for the most current parts listing. ITEM PART NO. DESCRIPTION NOTES 9390-123 Capscrew 5/8-11UNC x 1 3/4 Grade 5 9801 Locknut 5/8-11UNC 98115 Wheel/Tire 903052B Torsion Axle Assembly w/Brakes...

  • Page 97: Spare Tire Kit Components

    — Parts SeedVeyor 102 Spare Tire Kit Components Please visit www.unverferth.com/parts/ for the most current parts listing. DIA. x 6 5/8 2-13UNC 8 GB TOOTH ITEM PART NO. DESCRIPTION NOTES 2000622B Spare Tire Kit Includes Items 1 through 10 29736B...

  • Page 98: Telescopic Spout 2-Stage

    — Parts SeedVeyor 102 Telescopic Spout 2-Stage Please visit www.unverferth.com/parts/ for the most current parts listing. ITEM PART NO. DESCRIPTION NOTES 27629 6” Conveyor Telescopic Spout (71” Extended; 51 1/2 Collapsed) Includes Items 2 & 4 95870 Telescopic Spout 98060...

  • Page 99: Telescopic Spout 3-Stage

    — Parts SeedVeyor 102 Telescopic Spout 3-Stage Please visit www.unverferth.com/parts/ for the most current parts listing. ITEM PART NO. DESCRIPTION NOTES 22578 6” Conveyor Telescopic Spout 6’-10’ ONLY Includes Items 2, 3, 4 96855 Telescopic Spout 98060 Clamp/T-Bolt 22577 Sock Spout Extension...

  • Page 100: Platform For Units Less Undercarriage Kit #2003134Cg

    — Parts SeedVeyor 102 Platform for Units Less Undercarriage Kit #2003134CG Please visit www.unverferth.com/parts/ for the most current parts listing. ITEM PART NO. DESCRIPTION NOTES 2003078CG Adapter Bracket Weldment =Charcoal Grey= 2003079CG Stand Weldment =Charcoal Grey= 2003126CG S-Bracket =Charcoal Grey=...
  • Page 101 — Parts SeedVeyor 102 AG Decal Package (Optional) - S MV, SIS Decals, & Reflectors Please visit www.unverferth.com/parts/ for the most current parts listing. ITEM PART NO. DESCRIPTION QTY. NOTES 2010513 AG Decal Package Option 9003126 Reflector, RED 9003127 Reflector, AMBER...
  • Page 102 L:\PAGEMAKER_OM_FILES\OMUNFERFERTH\SEEDVEYOR\2000829.INDD\\\December 2013-0///October 2014-2//January 2019-3//October 2020-4/January 2022-5...

Table of Contents