Dust Collection System - Makita DHR183 Instruction Manual

Tool hanger
Optional accessory
CAUTION:
Do not use damaged tool hanger
and scre w . Before use, al w ays check for dam-
ages, cracks or deformations, and make sure that
the scre w is tightened.
CAUTION:
Install or remove the tool hanger
on a stable table or surface. Be sure to use the
scre w provided w ith the tool hanger only. After
installing the tool hanger, make sure that the tool
hanger is securely installed w ith the scre w .
CAUTION:
Do not remove the battery car-
tridge w hile hanging the tool. The tool may fall if the
s c r e w i s n o t t i g h t e n e d .
The tool hanger is intended for connecting the lanyard
( t e t h e r s t r a p ) .
B e f o r e i n s t a l l i n g t h e t o o l h a n g e r , r e m o v e t h e r u b b e r c a p
f r o m t h e s c r e w h o l e i n t h e m o u n t i n g b r a c k e t . I n s e r t t h e
s q u a r e n u t u n d e r t h e b r a c k e t . T i g h t e n t h e t o o l h a n g e r
w i t h s c r e w i n p l a c e .
Fig.23: 1. R u b b e r c a p 2. M o u n t i n g b r a c k e t
3. S q u a r e n u t 4. T o o l h a n g e r 5. S c r e w
Safety w arnings about connecting
lanyard (tether strap) to the tool
hanger
Safety warnings speci c for use at height
Read all safety w arnings and instructions. F a i l u r e
to follow the warnings and instructions may result in
serious injury.
1. Al w ays keep the tool tethered w hen w orking
" at height " . Maximum lanyard length is 2 m.
The maximum permissible fall height for lan-
yard (tether strap) must not exceed 2 m.
2. Use only w ith lanyards appropriate for this tool
type and rated for at least 6.0 kg.
3. Do not anchor the tool lanyard to anything on
your body or on movable components. Anchor
the tool lanyard to a rigid structure that can
w ithstand the forces of a dropped tool.
4 . Make sure the lanyard is properly secured at
each end prior to use.
5. Inspect the tool and lanyard before each use
for damage and proper function (including
fabric and stitching). Do not use if damaged or
not functioning properly.
6 . Do not w rap lanyards around or allo w them to
come in contact w ith sharp or rough edges.
7. Fasten the other end of the lanyard outside
the w orking area so that a falling tool is held
securely.
8. Attach the lanyard so that the tool w ill move
a w ay from the operator if it falls. D r o p p e d t o o l s
will swing on the lanyard, which could cause injury
o r l o s s o f b a l a n c e .
9 . Do not use near moving parts or running
machinery. Failure to do so may result in a crush
o r e n t a n g l e m e n t h a z a r d .
10. Do not carry the tool by the attachment device
or the lanyard.
11. Only transfer the tool bet w een your hands
w hile you are properly balanced.
12. Do not attach lanyards to the tool in a w ay that
keeps s w itches or trigger-lock (if supplied)
from operating properly.
13. Avoid getting tangled in the lanyard.
1 4 . Keep lanyard a w ay from the drilling area of the
tool.
15. Use a locking carabiner (multi-action and
scre w gate type). Do not use single action
spring clip carabiners.
1 6 . In the event the tool is dropped, it must be
tagged and removed from service, and should
be inspected by a Makita Factory or Authorized
Service Center.
17. Do not hang the tool on your w aist. H e a t e d t o o l
and its accessory may touch your skin and burn
injury result.
Fig.24: 1. T o o l h a n g e r 2. Lanyard (tether strap)
DUST COLLECTION
SYSTEM
Optional accessory
The dust collection system is designed to collect dusts
e ectively when the concrete drilling operation.
Fig.25: 1. Dust collection system
CAUTION:
The dust collection system is
intended for drilling in concrete only. Do not use
the dust collection system for drilling in metal or
w ood.
CAUTION:
W hen using the tool w ith the dust
collection system, be sure to attach the lter
to the dust collection system to prevent dust
inhalation.
CAUTION:
Before using the dust collection
system, check that the lter is not damaged and
the inner pipe is free of dust and foreign matter.
Failure to do so may cause dust inhalation.
CAUTION:
The dust collection system col-
lects the generated dust at a considerable rate,
but not all dust can be collected.
NOTICE:
Do not use the dust collection system
for core drilling or chiseling.
NOTICE:
Do not use the dust collection system
for metal or w ood. The dust collection system is
intended for concrete only.
NOTICE:
Do not use the dust collection system
for drilling in w et concrete or use this system
in w et environment. Failure to do so may cause
malfunction.
14 ENGLISH