Z GRILLS ZPG-450A Owner's Manual

Z GRILLS ZPG-450A Owner's Manual

Hide thumbs Also See for ZPG-450A:

Advertisement

Quick Links

WOOD PELLET GRILLS
ZPG-450A/ZPG-450APro
OWNER'S MANUAL
MON TO FRI, 8:00 A.M. - 5:00 P.M. PACIFIC STANDARD TIME
SERVICE CONTACT: 1-833-947-4557/1-833-ZGRILLS
EMAIL: support@zgrills.com
WEBSITE: www.zgrills.com
VN082020

Advertisement

Table of Contents
loading

Summary of Contents for Z GRILLS ZPG-450A

  • Page 1 WOOD PELLET GRILLS ZPG-450A/ZPG-450APro OWNER’S MANUAL MON TO FRI, 8:00 A.M. - 5:00 P.M. PACIFIC STANDARD TIME SERVICE CONTACT: 1-833-947-4557/1-833-ZGRILLS EMAIL: support@zgrills.com WEBSITE: www.zgrills.com VN082020...
  • Page 3: Table Of Contents

    CONTENTS IMPORTANT SAFETY INFO COMPONENT LIST ASSEMBLY INSTRUCTIONS INITIAL FIRING INSTRUCTIONS SUBSEQUENT START-UP OPERATING TIPS MAINTENANCE & CLEANING TROUBLESHOOTING DIGITAL THERMOSTAT CONTROL WIRING DIAGRAM Z GRILLS SUPPORT 3-Y LIMITED WARRANTY...
  • Page 4 SAVE THIS MANUAL FOR FUTURE REFERENCE...
  • Page 5: Important Safety Info

    IMPORTANT SAFETY INFO GENERAL WARNINGS Please read this entire manual before installation and use of the pellet fuel-burning appliance. Failure to follow these instructions could result in property damage, bodily injury or even death. Contact local building or fire officials about restrictions and installation inspection requirements in your area.
  • Page 6 DO NOT place anything heavy on top of hopper lid. It is not a shelf and is a tip hazard. Never use gasoline, gasoline-type lantern fuel, kerosene, charcoal lighter fluid, or similar liquids to start or ‘freshen up’ a fire in this appliance. Keep all such liquids well away from the appliance when in use.
  • Page 7 There is no guarantee that other brands of pellets are suitable for use in Z GRILLS. And Z GRILLS assumes no liability for any loss, damage or injury caused by the use of any other brands of pellets.
  • Page 8: Component List

    COMPONENT LIST ITEM DESCRIPTION ITEM DESCRIPTION Hinge Assembly Hopper Lid Handle Wheels Firepot Welding Assembly Axle Bolt Name Plate Wheeled Leg Base Lid Handle Footed Leg Base Grill Chamber Assembly Heat Baffle Hopper Assembly Grease Drain Pan Chimney Cap Assembly Porcelain Grills Smoke Stack Assembly Warming Rack...
  • Page 9 HARDWARE PACKAGE LIST ITEM DESCRIPTION ITEM DESCRIPTION Hexagon Bolt 1/4-20×1/2 Hexagon Nut 1/4-20 Bolt 1/4-20×1/2 Gasket (OD0.75×ID0.4) Step Screw 1/4-20 Gasket (OD0.6×ID0.25) Screwdriver Cap Nut 1/4-20 Spring Washer Open End Wrench (OD0.4×ID0.25) Cap Nut 5/16-18 Bolt 8#-32×4/17 Gasket (OD0.73×ID0.25)
  • Page 10: Assembly Instructions

    ASSEMBLY INSTRUCTIONS PARTS DIAGRAM...
  • Page 11 HOPPER BURNER ASSEMBLY BODY FRAME ASSEMBLY 1. Attach 2pcs Leg A B (20) (21) to the Leg Base (28) (29) with Bolt (B), Spring Washers (E), Flat Gasket (J) orderly. 2. Insert Axle Bolt (27) through the hole in Wheel (25) and Wheeled Leg Base (28). 3.
  • Page 12 1.MOUNTING THE BODY FRAME TO THE CHAMBER Turn the Grill Chamber Assembly (7) over, attach the Wheeled Leg Assembly and the Footed Leg Assembly using Bolts (B), Spring Washers (E), Gaskets (J) as shown. Use the Screwdriver (K) to tighten. 2.INSTALLING CHAMBER HANDLE TO LID 1.
  • Page 13 3.ATTACHING HOPPER HANDLE TO HOPPER LID Keep the Hopper Burner Lid (44) open. Penetrate the Bolt (F) into the hole on the Hopper Burner Lid (44), then install the Hopper Lid Handle (24) by screwdriver. 4.ATTACHING THE SMOKESTACK AND CHIMNEY CAP Place Bolt (A) through the holes of Smokestack (10) and the holes of Smokestack Insulation (11), attach two Bolts (A), then attach Gasket (G) and Nuts (H), using the Wrench to tighten them.
  • Page 14 5.ATTACHING LATERAL FLAT PALLET AND FRONT FLAT PLATE 1. Insert 3 Bolts (B) through the Left Front Table Bracket (14) and into the Grill Chamber Assembly (7). 2. Insert the Step Screw (C) through the Left Front Table Bracket (14) and Spring Washer (E), attaching the Cap Nut (D) then using the Screwdriver (K) and Wrench (L) to tighten them.
  • Page 15 7.POSITIONING THE GREASE DRAIN PAN Place the Grease Drain Pan (31) on the Pan Support in the Grill Chamber Assembly (7) The 2 slots in the Grease Drain Pan (31) should fit over the corners of the Pan Support. 8.ATTACHING COOKING GRATE AND WARMING RACK Attaching the Porcelain Cooking Grate (32) and Warming Rack (33) in the chamber.
  • Page 16 9.HANG ON THE GREASE BUCKET Locate the Grease Drain Tube which is on the right side of the chamber. Hang the Grease Bucket (19) on the hook as shown.
  • Page 17: Initial Firing Instructions

    Please read this manual carefully and follow it step by step before starting your Z Grills for the first time and each time the grill runs out of pellets. 1.Remove the Porcelain Grills, Grease Drain Pan and Heat Baffle from the interior of the grill.
  • Page 18: Subsequent Start-Up

    Temperature Dial to any cooking setting desired. 5.If this step is not successful, see TROUBLESHOOTING or contact Z GRILLS Technical Support to help diagnose the problem.
  • Page 19: Operating Tips

    OPERATING TIPS 1.Like all grills, the actual temperature of this grill and the cooking times will be affected by external temperature, humidity, wind conditions, quality of pellets, etc. 2.It is beneficial to shelter your grill from the wind. This will aid in temperature output, heat retention and heat recovery time when the lid is open.
  • Page 20: Maintenance & Cleaning

    2.It is highly recommended that you use Z GRILLS Cover to protect your grill . 3.You can use a high-quality car wax on the outside surfaces of your grill to protect it’s finish.
  • Page 21 Clean the ash from the interior of the grill periodically. If excessive ash is in the firepot, it may cause the fire to go out. This is especially true in the SMOKE setting. A shop vac is an excellent tool to use for removing the ash. WARNING: MAKE SURE THE GRILL FIRE IS OUT, THE UNIT IS OFF, UNPLUGGED AND COLD BEFORE ATTEMPTING TO CLEAN ASH FROM THE GRILL.
  • Page 22: Troubleshooting

    TROUBLESHOOTING CAUTION: Make sure the grill is completely cool and unplugged before you do any inspection, cleaning, maintenance or service work. Potential Problem Solution Cause Make sure the power cord is plugged Power in. Verify there is power at the electrical outlet.
  • Page 23 Pellets pellets. When contacting customer support Contact please have the following information Z GRILLS available: Your authorized Z Grills Customer dealer, your name, phone number, Get your new parts Service or your address, your Z Grill serial number and Z GRILLS part identification number.
  • Page 24: Digital Thermostat Control Wiring Diagram

    DIGITAL THERMOSTAT CONTROL WIRING DIAGRAM...
  • Page 25: Z Grills Support

    Thank you for purchasing a Z GRILL! If you have any question, please contact customer support or your Z GRILL dealer. Z GRILLS, INC. offers the best technical and sales support in the industry. When calling customer please be prepared to provide the following information: 1.Dealer's name and date of purchase...
  • Page 26: 3-Y Limited Warranty

    Z GRILLS, Inc. shall not be liable if you install, operate, clean or maintain your grill without following the owners' manual instructions. Misuse, abuse, alteration and natural disasters...

This manual is also suitable for:

Zpg-450apro

Table of Contents