Subscribe to Our Youtube Channel
Related Manuals for Andersen 82-3ST
Summary of Contents for Andersen 82-3ST
- Page 1 PRODUCT MANUAL 82-3ST Winch FOR USE WITH: Manual Winch: RA2082010000 ≥ V.1.0 Winch Versions: Rev.0...
-
Page 2: Safety Notices
Safety Notice Sheet and the Product Manual. Stay Alert When Operating Andersen winches are very powerful and have the potential to cause significant damage and/or serious injury if used improperly or without due caution and vigilance. Operators Must be Trained... -
Page 3: Winch Assembly
WINCH ASSEMBLY EXPLODED VIEW & PARTS LIST Item no. Qty. Description Part no. Main drive gear set 82-3ST 539604 3rd speed gear set 82-3ST 538003 Central gear set 82-3ST 539704 Base 82-3ST 741607 Centre stem assembly 82-3ST 741511 ® Torlon ball dia. - Page 4 82-3ST 539902 Collets 713200 Pawl for arm spring 713300 Pawl spring, arm 539903 Retainer ring 3rd Speed Gear Set 82-3ST Item Qty. Part no. Description 538004 Small 3rd speed drive gear 537501 Large 3rd speed drive gear 537800 Cover washer 82-3ST...
- Page 5 Main Drive Gear Set 82-3ST Item Qty. Part no. Description ② 542215 Cover plate/ bearing ⑫ 532604 Thrust washer, top ⑪ 542230 Pawl carrier,auto-switch centerpiece 542210 Drive gear 82-3ST ⑩ 713200 Pawl for arm spring 713201 Pawl for auto-switch 82- ④...
-
Page 6: Installation
ANDERSEN Stainless Steel Winches ® Your Andersen winch is made with the care and craftsmanship that come from more than sixty years of experience. Andersen winches are built to last, to retain their exceptional finish and to deliver season after season of reliable performance and sailing pleasure to their owners through the years. - Page 7 Step 2 Prepare the mounting surface After confirming the mounting location and orientation of the winch, clean the mounting surface and place the drilling template in the required position on the deck. Ensure that the surface is flat and there is adequate space and clearance below deck for access to mounting bolts.
-
Page 8: Operation Checks
OPERATION CHECKS Check manual operation of the winch First check the winch by rotating the drum by hand. Then use a winch handle to operate the winch manually, turning the handle in both directions with no load on the drum. The winch should operate smoothly in both gears, always with the drum rotating only in a clockwise direction. -
Page 9: Service And Maintenance
Andersen Winch Grease to the pawls. Do not use any other kind of grease for this purpose. Check the functioning of each pawl by pushing the pawl against the spring. The pawls should move smoothly and automatically return to their normal position where the pawls engage within the gears. - Page 10 11. Apply grease to the gearwheels and teeth. Put these gear sets aside for the moment and proceed with the next step. 12. Main Drive Gear Set Service The main drive gear set (1) contains the clutch that engages and disengages to provide 3rd gear or 1st gear operation when turning the winch handle in a clockwise direction.
- Page 11 4 angled sliders align with the corresponding slide paths machined into the drive gearwheel. Use Andersen Winch Grease on the gear teeth, bearing surfaces and slide paths, and a very thin film of the same grease on the pawls.
- Page 12 NOTES CONTACT Andersen Stainless Steel Winches ® are manufactured by Ronstan Denmark ApS. Jægervænget 36 7100 Vejle Denmark info@andersenwinches.com WORLDWIDE DISTRIBUTION & SERVICE andersenwinches.com WARRANTY andersenwinches.com Andersen Stainless Steel Winches is a registered trademark of Ronstan Denmark ApS ®...
Need help?
Do you have a question about the 82-3ST and is the answer not in the manual?
Questions and answers