ureach PE-H Series User Manual

Nvme/sata m.2 ssd duplicator and sanitizer

Advertisement

Quick Links

PE-H Series
NVMe/SATA M.2 SSD
Duplicator and Sanitizer
User Manual
v A.02

Advertisement

Table of Contents
loading
Need help?

Need help?

Do you have a question about the PE-H Series and is the answer not in the manual?

Questions and answers

Summary of Contents for ureach PE-H Series

  • Page 1 PE-H Series NVMe/SATA M.2 SSD Duplicator and Sanitizer User Manual v A.02...
  • Page 2: Table Of Contents

    Index Table v A.02 Product Disclaimer ......................... 3 Warranty..........................3 Piracy Statement ........................3 Before You Start ........................4 Notice Symbols ........................4 Functions Table ........................5 Product Overview ........................ 10 Functions ..........................12 1.Copy ........................... 12 2. Compare ........................13 3.
  • Page 3: Product Disclaimer

    Product Disclaimer U-Reach is not accountable for any incidental or consequential damages, including, but not limited to property harm, loss of time or data from use of any U-Reach product, or any other damages attributable to product malfunction or failure of including without limitation, those attributed to reliance of the materials provided, costs of product replacement, loss of use, data or profits, delays or business interruptions, any principle of legal responsibility arising from or in reference to the use, overall performance, delays in...
  • Page 4: Before You Start

    Before You Start Important Notice Carefully read the entire manual before operating. ● Make sure the source device is correct and functioning. ● Equal capacity of source and target is recommended for guaranteed data consistency. ● Using the Copy+Compare function provides the most flawless duplication. ●...
  • Page 5: Functions Table

    Functions Table Functions Descriptions 1.1 Source Port Copies data from the device connected to the Source Port (Port #1). 1. Copy 1.2 Internal Storage (Available when internal SSD is installed) Copies saved data images from the duplicator’s internal storage device. 2.1 Source Port Verifies data, bit-by-bit, from the device connected to the Source Port (Port #1).
  • Page 6 5.3 System Info Displays system information such as controller, model number, software version, etc. 5.4 Calc. CRC64 Calculates the CRC64 value of the source device. 6.1 Start-up Menu Sets default function to display during equipment initialization. 6.2.1 System and Files Copies data and skips empty space.
  • Page 7 One Byte Random character written per byte. 6.6.3 Erase Pattern Big Random Data Random character written in a set of area. 6.6.4 Skip Erase Errors Skips bad sectors during Erase. Keep Target HPA Does not copy HPA data but keeps target device’s original HPA setting.
  • Page 8 6.6.9 Stop Motor Time Sets device power down buffer time when tasks are completed. 6.6.10 Boot Password Sets up the login password. 6.6.11 Delete Disk Signature After Copy Do not copy the disk signature onto target devices. Normal 6.6.12 PCIe Speed Sets data transmission speed.
  • Page 9 8.1 Copy SSD to Image Uploads the source data onto internal SSD. 8.2 Compare SSD with Image Compares the source data with an image file stored in the internal SSD. 8.3 Show Image Tank 8. Image Displays the disk information of the internal SSD. Manager (Available when 8.4 Show One Image...
  • Page 10: Product Overview

    Product Overview  Front View USB port for Log Report Outputs and Firmware Control Buttons Updates. OK Button LCD Display SSD slot for saving Master Image.  Back View USB Port for PC-LINK Power Input Grounding Port Power Switch...
  • Page 11  LED Status Yellow: Powered Green: Pass Red: Fail  LCD Configuration Number of Target Device Confirm/OK Total Size Forward Function Backward The slowest Cancel/Back Device Time elapsed and Copied processed size copy progress...
  • Page 12: Functions

    Functions 1.Copy Step 1: Prepare source and target devices. Recommendation: Target device(s)’ capacity must be equal to or larger than Note the source device capacity. Step 2: Connect source and target devices. Step 3: Proceed to copy. Scroll to select “1. Copy”, then press “OK” to select which source to copy from. Scroll to select “1.1 Source Port”...
  • Page 13: Compare

    1.2 Internal Storage (Available when internal SSD is installed) Scroll to select “1. 2 Internal Storage”, then press “OK” to select which GOB Image to copy from the duplicator’s built-in storage device. The GOB Image is created through U-Reach’s proprietary software that is included with the duplicator. 1.
  • Page 14: Erase

    Scroll to select “3. 1 Source Port”, then press “OK” to copy to and verify targets from the source port. 3.2 Internal Storage (Available when internal SSD is installed) Scroll to select “3. 2 Internal Storage” , then press “OK” to select which GOB Image to copy and verify from the duplicator’s built-in storage device.
  • Page 15: Utility

    This function will erase all data per DoD 5220.22-M Standards of the connected device(s). Scroll to select “4.3 DoD3 Pass”, then press “OK” to start the erasing process. 4.4 DoD3 Pass+Compare This function will erase all data per DoD 5220.22-M Standards, then verifies the erasure of the connected device(s).
  • Page 16: Setup

    The firmware update process may take longer than 5 minutes. Please do not Caution disrupt power or process during BIOS update. If interrupted, the system will become useless. U-Reach will not be held responsible for any damages. 5.3 System Info This function will display basic information such as device model, name, capacity, etc…...
  • Page 17 ⚫ Selecting the Proper Copy Modes Example: There are two defined partitions in a 500GB device. The charts below illustrate what portion would be duplicated. System and Files All Partitions Whole Device 30GB Data 30GB Data 30GB Data 100GB 100GB 100GB 70GB 70GB...
  • Page 18 6.2.2 All Partitions Copy or skip HPA, DCO, unknown partitions, modified formats, etc. defined by settings. Scroll to select “6.2.2 All Partitions”, then press “OK” to save the copy method. The target device’s capacity must be equal to or larger than the source device’s capacity. 6.2.3 Whole HDD Copies all source data, bit-by-bit.
  • Page 19 6.2.4 Percentage (%) Select percentage of source capacity to copy. Scroll to select “6.2.4 Percentage”, then press “OK” to save the copy method. 6.2.5 Deep Analysis Scan the entire SSD, the duplicator will only copy the data area where the data stored. 1.
  • Page 20 6.3 Copy GPT Backup Area Enabling this function allows the duplicator to copy from big capacity device to small capacity device(s). Note The partition size of the source SSD must be smaller than target capacity. GPT Index Partition Disabling function “6.3 Copy GPT Backup Area” will force the duplicator to ignore this area.
  • Page 21 6.6 Advanced Setup This function contains settings to fine tune copy and erase functions. Scroll to select “6.6 Advanced Setup”, then press “OK” to view the submenus. 6.6.1 Unknown Format This function only works with copy functions: “System and Files” and “All Partition”. Scroll to select “Unknown”, then press “OK”.
  • Page 22 Scroll to select “Big Random Data”, then press “OK” to save this setting. 6.6.4 Skip Erase Errors Skip source bad sectors during Erase. Bad sectors can be set as unlimited or at a value from 0 to 65,535. The default setting is “0”. Scroll to select “6.6.4 Skip Erase Errors”, and press “OK”...
  • Page 23 Scroll to select "Clear HPA at Erase”, then press "OK" to save this setting. ◼ Release Clears HPA setting and data during erase. Scroll to select "6.6.6 Clear HPA at Erase >> Release”, then press "OK" to save this setting. ◼...
  • Page 24 ◼ Enabled Requires the password to start-up the system. Caution The system must be sent back for reset if the password is forgotten. 6.6.11 Delete Disk Signature After Copy Set at “Yes” means do not copy the disk signature part. This function is for Windows only.
  • Page 25: Log Manager

    7. Log Manager This menu allows user to access several submenus. Scroll to select “7. Log Manager”, then press “OK” access submenus. Log Report Diagram Background information of this log report Source device Info. Original Source Record Result Date Time Lapsed Time Model No.
  • Page 26 ➊ Out Today Report Export today’s log report via USB port to a USB drive. ➋ Out Recent Report Exports a recent log report (1-28 days) via USB port to a USB drive. ➌ Out Period Date Exports a specific time period’s log report via USB port to a USB drive. 7.1 Out Today Report Outputs current day log report Scroll to select “7.1 Out Today Report”, then press “OK”...
  • Page 27: Image Manager(Available When Internal Ssd Is Installed)

    Scroll to select “7.4.3 Adjust Clock”, then press “OK” to adjust the time and date. 7.4.4 Add Watermark at text File Creates watermark on the log report. The log report can be checked by software (iSecuLog.exe) to prevent modifying. Note Contact with U-Reach technical team for related software and operation details. 8.
  • Page 28: Image Management

    Image Management Users can easily create a GOB image on PC, upload it to the machine and do duplication. 1. Software Introduction 1.1 Connect the PC Link USB drive/disc on PC, it will show two folders. PCIe Software: The installation software is stored in this folder. Please copy the folder from PC Link USB drive/disc to PC.
  • Page 29 in the right. Please note the GOB Image file will not copy to smaller target capacities than Caution the original source drive capacity. 2.4 There are 3 modes for making GOB image files, System and Files, Whole Device, and Depth Profiling Analysis. ➊...
  • Page 30 ➋ Whole Device a. Click "Whole HDD," named the image and click "Save." The GOB file will be created. D:\Scan Test01 b. During compiling process, the percentage of production is shown in the "Progress". c. After completion, the detail of image information will display at the bottom. D:\Scan CRC32:D68BA4C...
  • Page 31 ➌ Depth Profiling Analysis This function is specially designed for data format which “System and Files copy mode” doesn’t support. It detects data area in the source and makes the image file. a. Click "Deep HDD," name the image and click "Save." The device will start the deep analyze process, and the GOB file will be created.
  • Page 32 3.3 Double click and execute “GOB Uploader application.” 3.4 After successful detection, a popup menu will display (shown in the figure below). Click OK to “Format HDD FOR FIRST USE. “This format the internal SSD installed in the PCIE duplicator. 3.5 Once formatted, click “Upload”...
  • Page 33 ● A maximum of two duplicators can be connected. If more than two duplicators are connected, a popup menu will display an error message “Machine ID Not Match!” ● To resolve the error, all files must be deleted, except “GOB Uploader application”...
  • Page 34 ◼ Format HDD: Format the internal SSD in the PCIE duplicator. Caution Please backup all important data before using this function. ◼ AutoCopy: It will automatically copy after the image is uploaded. *Specifications subject to change without notice.

Table of Contents