Advertisement
PROGRAMMING
Deleting transmitters
In delete mode, individual transmitters can be specifically deleted from the memory of the RCJ33.
Operation
(1)
Indication
[Press button]
P
1x long
LED P flashes quickly red
Tx 1x briefly
LED P lights
2 seconds red
Reset
Doing a RESET, the receiver will be set back to the factory settings. All programmed transmitters are
deleted and the TIMER is set to 7 minutes.
Operation
(1)
Indication
[Press button]
P 1x long
LED P flashes quickly red
P 1x long
LED P lights
4 seconds red
BI-DIRECTIONAL FUNCTIONS (Easywave neo)
In order to be able to use bidirectional functionalities, a server (e.g. APC01) can be programmed into the RCJ33. The available functions are automatically
detected, so no specific operation type needs to be selected when programming a server. Program the server into the receiver according to the instructions
in the respective server application by adding an ELDAT actuator as an „Easywave neo" device. After it is programmed, the server receives feedback about
each switching operation performed, even if this is triggered by another transmitter or manually via the external button on the RCJ33. The current state of the
receiver is therefore always displayed in the associated application.
Program server
Add an actuator in the Easywave app as an Easywave neo device and follow the instructions in the
app. Only one server can be programmed into the receiver. Any server that may have already been
programmed will be overwritten.
Operation
(1)
Indication
[Press button]
Start the programming process via the server application.
P 1x briefly
LED P flashes red
Complete the programming process via the application.
Once a server is programmed to the RCJ33, an acknowledgement for each switching opera-
tion is transmitted via radio. If the server is not in use, delete it from the receiver to prevent
unnecessary radio transmissions.
Delete the server
A server can be removed from the RCJ33 by deleting the relevant device in the server application. To
delete the server, the receiver must be powered and within range of the server. As an alternative to
deleting it via the app, the server can also be deleted by resetting the receiver.
Delete the receiver or relevant Easywave neo actuator in the server application, while the recei-
ver is powered and within range of the server.
GENERAL INFORMATION
Disposal
Waste electrical products should not be
disposed of with household waste!
Dispose of the waste product via a
collection point for electronic scrap or
via your specialist dealer.
Put the packaging material into the
recycling bins for cardboard, paper
and plastics.
Note
Receiver in delete mode.
Transmitter has been deleted.
Note
Receiver in delete mode.
All transmission codes have been deleted and
the factory settings have been restored.
Note
Receiver in programming mode
any operating mode possible
Warranty
We will remedy defects on the device based on
material or production errors or exchange the de-
vice within the statutory warranty period.
Any unauthorized tampering with, or modifica-
tions to, the product shall render this warranty
null and void.
Conformity
Hereby, ELDAT EaS GmbH declares that the ra-
dio equipment type RCJ33 is in compliance with
Directive 2014/53/EU. The full text of the EU de-
claration of conformity is available at the following
internet address: www.eldat.de
P
c
d
>2 s
c
P
d
>2 s
c
Start programming
process in the server
application
d
P
Put the receiver in programming mode
e
Finish the programming
process in the appli-
cation
Customer Service
If the device does not work properly despite pro-
per handling or in case of damage, please contact
the manufacturer or your retailer.
ELDAT EaS GmbH
Schmiedestraße 2
15745 Wildau
Germany
Phone:
+ 49 (0) 33 75 / 90 37-310
Fax:
+ 49 (0) 33 75 / 90 37-90
Internet: www.eldat.de
E-mail:
info@eldat.de
Tx
P
>2 s
Advertisement
