Page 1
ORIGINAL INSTRUCTIONS ELECTRICAL MULTI TOOL KIT (Brush cutter, grass trimmer, pole saw and hedge trimmer) INSTRUCTIONS MANUAL RAC4IN1E-1-UK CAREFULLY READ THESE INSTRUCTIONS BEFORE USE THIS MACHINE KEEP THIS MANUAL FOR FUTURE REFERENCES RACING 32, rue Aristide Bergès - ZI 31270 Cugnaux – France...
1. SAFETY INSTRUCTIONS WARNING Read all safety warnings and all instructions. Failure to follow the warnings and instructions may result in electric shock, fire and/or serious injury. Save all warnings and instructions for future reference. The term "power tool" in the warnings refers to your mains-operated (corded) power tool or battery-operated (cordless) power tool.
Page 4
f) Keep cutting tools sharp and clean. Properly maintained cutting tools with sharp cutting edges are less likely to bind and are easier to control. g) Use the power tool, accessories and tool bits etc. in accordance with these instructions, taking into account the working conditions and the work to be performed.
Page 5
Secure the machine during transport to prevent damage or injury. The tool must be always unplugged. Put the protection on the blade if any. Hold the handle, never the blade. Before storage, the tool must be cleaned and regular maintenance must be provided. When storage, always put the protection on the blades.
Page 6
4) After striking a foreign object; 5) Whenever the machine starts vibrating abnormally. h) Take care against injury to feet and hands from the cutting means. i) Always ensure that the ventilation openings are kept clear of debris. Maintenance and storage a) Disconnect the machine from the power supply (i.e.
Page 7
A damaged guard or other part must be properly repaired or replaced by an authorized service center, unless otherwise specified in this instruction manual. Do not move the chain with your hand with the wheel moving. Do not stop the blade with your hands or other objects. ...
Page 8
Nylon cutting Blades Warning symbol Do not use the tool when raining Keep bystanders away Unplug the tool: When the plug/cable is damaged or entangled Before maintenance, servicing, storage Risk of projections Do not touch with the tool foreign objects while it is in operation Beware of the kickback Keep feet away from the cutting mains People must kept away from the work area (15 m)
Page 9
Do not touch the cutting parts Keep hands and feet away from sharp accessories! Do not stand in the place where the limbs will fall Residual risks Even if you use this product in compliance with all safety requirements, the potential risks of injury and damage remain.
Use this multifunction tool only as described in this manual and only for the intended use as described above. Any other use might lead to damage of the appliance, property or personal injury. No liability will be accepted for damage resulting from improper use or non-compliance with this manual.
Page 11
A- Power unit (motor) 6- Grass trimmer nylon spool 1- Motor unit 7- Nylon wire cutter blade 2- Rear Handle 3- Trigger switch C- Pole pruner chainsaw attachment 4- Safety switch 1- Drive shaft (inside the tube) 5- Belt 2- Tube 6- Belt anchor point 3- Gear 7- Secondary handle...
7200/min 6900/min No load speed BRUSHCUTTER Cutting attachments 230mm , 3 tooth metal blade Mass 3,4 kg No load speed 6900/min Hedge trimmer: 101.22 dB(A) Brushcutter: 98.53 dB(A) Sound power level Grass trimmer: 102.47 dB(A) Pruner: 102.36 dB(A) K = 3 dB(A) Hedge trimmer: 90.22 dB(A) Brushcutter: 91.1 dB(A) Grass trimmer: 91.2 dB(A)
Page 15
HANDLE ASSEMBLY (FIG 3) Loosen the tightening knob (A9). Open the handle bracket (a). Fit the handle (A7) onto the power unit main tube (A8). Close the bracket (a) and tighten the knob (A9). CONNECTING AN ATTACHMENT (FIG.4 & 5 & 6) Fig 4 Applicable to first time assembly only.
Page 16
Fig 5 Loosen the tightening knob (A9) onto the connecting bracket (b) on the main tube (A8). Press the lock button (d). Align and connect the drive shaft (A10) of the power unit with the draft shaft (1) of the tool attachment.
Adjust the cutting head to desired working angle then lock the ratchet (C8) and the locking pin (n) ensuring that they both lock firmly into their notches. Hedge trimmer This attachment comes supplied fully assembled. For service: lubricate with a grease gun every six months or 20 hours of use. Adjustable working angle (Fig.13+14) NOTE: Always fit the blade cover To adjust the cutting angle in one of the seven positions, please proceed as follows:...
Page 18
When you operate the tool, always wear full-length trousers, as well as sturdy, closed footwear that provide good support. Do not operate the tool wearing shorts, when barefoot or wearing open sandals. Do not wear loose clothing or jewellery that van be drawn into the moving parts. Keep long hair away from the moving parts (for example put it in a hair net).
Page 19
Place the cutting element above the cutting area. Do not make sudden movements. During use Always direct the cable to the rear away from the tool and working path. Make sure the power cord is kept behind and away from the device while you work. If the power cord or extension cord becomes damaged during use, disconnect the supply cord from the mains immediately.
Page 20
Cutting limbs of fallen trees Check if to which side the limb is bent. Than make the initial cut from the bent side and finish by saving from the opposite side. WARNING! Be alert the springing back of a cut limb Pruning a sanding tree Cut up the bottom, finish down the top.
Page 21
In order to lubricate the saw chain sufficiently, there must be enough saw chain oil in the tank at all times. The oil level can be checked in the viewing glass. The oil level may not be below or above MIN or MAX. Saw chain lubrication Clean to avoid premature wear of the tool, the chain and the guide bar must be lubricated homogeneously throughout the operation.
Page 22
Scything weeds This is cutting be swinging the blade in a level This method quickly allows to clear areas of field grass and weeds. Scything should be not be used to cut large, though weeds or woody growths. Scything can be done in both directions (warning! Debris may be thrown towards user’s direction) or just in one direction (which results in the debris being thrown away from the user).
Do not use a steel blade for edging or scalping Do not trim in any area where there are strands of fencing wire Do not cut where you cannot see what the cutting device is cutting. Adjusting the line length The grass trimmer is equipped with a semi-auto type nylon line head that allows the operator to advance the line without stopping the engine.
Always check the machine before and after the use. In case of malfunction or damaged parts, do not use the tool and bring it to a qualified service for inspections and reparations. Do not repair the tool by yourself. Only use original accessories and spare parts. Contact our service or your dealer to know the recommended parts/accessories to use.
ZI, 32 rue Aristide Bergès – 31270 Cugnaux – France Declare that the following machine: ELECTRICAL MULTI TOOL KIT (Brush cutter, grass trimmer, pole saw and hedge trimmer) RAC4IN1E-1-UK Serial number: 20170802065-20170802364 In conformity with the Directive Machine 2006/42/EC and with the regulations transposing it.