Advertisement
Quick Links
Advertisement
Related Manuals for Tiger PRESSURE TREATED APEX
Summary of Contents for Tiger PRESSURE TREATED APEX
- Page 1 TIG/INS72 TIGER PRESSURE TREATED APEX GENERAL ASSEMBLY INSTRUCTIONS...
-
Page 2: Before You Get Started
BEFORE YOU GET STARTED PLEASE READ INSTRUCTIONS CAREFULLY • Check the pack and make sure you have all the parts listed. • When you are ready to start, make sure you have the right tools at hand (not supplied). • Ensure there is plenty of space and a clean dry area for assembly. TIMBER As with all natural materials, timber can be affected during various weather conditions. - Page 3 Please retain instructions for future reference CAUTION: CAUTION: All buildings should be erected It is advisable to wear gloves by two competent adults. during building installation. MADE IN THE UK SINCE 1913. We have been making our high quality, great value garden buildings here in Britain for decades.
- Page 4 BEFORE YOU GET STARTED - PRE ASSEMBLY TOOLS REQUIRED: We recommend using the following tools (not supplied): HAMMER RUBBER MALLET LADDER TAPE MEASURE SHARP KNIFE SPIRIT LEVEL SCREWDRIVER + WOOD SAW SPANNER FIXING KIT GUIDES: FX06 - NAIL KITS HEAVY DUTY For Heavy Duty Shed Products: CN13 Clout Nails...
- Page 5 Please retain instructions for future reference • Assembly is straightforward if you follow these step-by-step instructions. • We recommend getting everything aligned properly before screwing together and that screw holes should be pre-drilled to avoid splitting the timber. (Do not come pre-drilled). IMPORTANT •...
- Page 6 TIGER PRESSURE TREATED APEX - GENERAL ASSEMBLY INSTRUCTIONS Step 1: LAYING THE FLOOR • SINGLE FLOOR - Lay floor down in the desired position. (Detail A1) • MULTI FLOOR (excluding 10x8 & 12x8) - Lay floors down in the desired position and butt together.
- Page 7 Please retain instructions for future reference Step 2a: INSTALLING SIDE AND GABLE PANELS • Position one end gable and side panel as shown. (Detail B1) NOTE: CHECK THAT ALL PANELS ARE AT RIGHT ANGLES TO EACH OTHER AND THE FLOOR. •...
- Page 8 TIGER PRESSURE TREATED APEX - GENERAL ASSEMBLY INSTRUCTIONS Step 2b: INSTALLING SIDE AND GABLE PANELS • For side panels made of 2 or more sections, secure together using 3x N100 evenly spaced through internal framework. (Detail B3 & B4) DO NOT FIX TO FLOOR.
- Page 9 Please retain instructions for future reference Step 3a: SECURING SIDE AND GABLE PANELS • Locate pre-drilled holes in gable panels. (Detail C1) NOTE: THESE MAY HAVE COVERED OVER DURING PANEL COATING PROCESS. THEY MAY RESEMBLE NAIL HEADS. • Use 4x CB100 per gable, through the pre-drilled holes in each gable, from the outside. (Detail C2) NOTE: DO NOT FULLY TIGHTEN.
- Page 10 TIGER PRESSURE TREATED APEX - GENERAL ASSEMBLY INSTRUCTIONS Step 3b: SECURING SIDE AND GABLE PANELS • Secure panels to the floor using 2x N100 per panel. Ensure the N100 are driven through the panels and into the floor bearers. (Detail C4) NOTE: PANELS HAVE BEEN REMOVED FOR CLARITY.
- Page 11 Please retain instructions for future reference Step 4: INSTALLING ROOF TRUSSES (Certain Sizes Only) • Before fitting roof panels fit apex truss, if supplied. Products with sides 10ft - 19ft are supplied with x1 truss (inc. clips) for centre of building. 20ft models are supplied with 3x trusses (inc. clips) to be equally spaced. •...
- Page 12 TIGER PRESSURE TREATED APEX - GENERAL ASSEMBLY INSTRUCTIONS Step 5a: TOP TIP You may need someone to hold roof panels together while you secure SINGLE PIECE ROOF INSTALLATION roof panels at the apex. • Attach roof panels as shown. There will be a slight gap between the roof panels at the apex of shed.
- Page 13 Please retain instructions for future reference Step 5b: MULTI PIECE ROOF INSTALLATION • For roofs that come in 4 sections. Layout panels for each side as shown on a flat, dry surface and secure together along apex purlin (and any internal purlins) using 600mm batons supplied in polytube pack. Use x4 N100 per baton so that roof panel side is one piece.
- Page 14 TIGER PRESSURE TREATED APEX - GENERAL ASSEMBLY INSTRUCTIONS Step 6: FELTING THE ROOF - MEASURE AND CUT BEFORE FITTING • Roll felt out onto a clean flat surface 30 minutes before you need it so it has a chance to flatten out.
- Page 15 Please retain instructions for future reference Step 7: FITTING FASCIA BOARDS & FINIAL (BARGEBOARDS) • Fit bargeboards to the roof panels, trapping overhanging end of the felt in between the roof panel and bargeboard. Secure using 2x N40 per bargeboard through apex and low side purlins. NOTE: THERE ARE NO BARGEBOARDS SUPPLIED FOR LOW SIDE OF ROOF AS THIS WILL PREVENT EFFECTIVE WATER DRAINAGE.
- Page 16 TIGER PRESSURE TREATED APEX - GENERAL ASSEMBLY INSTRUCTIONS Step 8: FIT CORNER STRIPS AND COVER STRIPS - CERTAIN SIZES ONLY • Secure the corner strips at each corner of the shed with 4x N40 per corner strip. NOTE: THESE CORNER STRIPS MAY NEED CUTTING TO SIZE.
- Page 17 Please retain instructions for future reference Step 9: INSTALLING GLAZING • Glaze windows by securing glass/styrene with PP25 supplied, from the inside. (Detail H) NOTE: ALL WINDOWS MUST BE SEALED INSIDE AND OUT WITH SILICONE, PUTTY, OR ANY OTHER WATER-TIGHT SOLUTION. (NOT SUPPLIED). NOTE: PLEASE DO NOT CONFUSE YOUR CORNER STRIPS WITH WINDOW BEADING.
-
Page 18: Installing Door Handle
TIGER PRESSURE TREATED APEX - GENERAL ASSEMBLY INSTRUCTIONS Step 10: INSTALLING DOOR HANDLE • Insert the spindle into one of the levers and securely fix the grub screw, ensuring enough of the spindle is free to pass through the door and to be secured in the opposing lever. - Page 19 Please retain instructions for future reference...
- Page 20 TIG/INS72 Display Agent Woodlands DIY Store Station Yard, Horsforth, Leeds, LS18 5NZ Telephone: 0113 205 4189 Website: tigersheds.com Email: customersupport@tigersheds.com...