Table of Contents
Advertisement
Quick Links
Advertisement
Table of Contents
Related Manuals for Ebyte E610-433T30S
Summary of Contents for Ebyte E610-433T30S
- Page 1 E610-433T30S User Manual 433MHz 1W Wireless high-speed connection module...
-
Page 2: Table Of Contents
ONTINUOUS TRANSMISSION MODE MODE 1) ............................14 6.3 G ENERAL TRANSMISSION MODE 2) ............................14 6.4 U SER CONFIGURATION ATTERN 3） ................................15 6.5 D （M SLEEP MODE CHAPTER Ⅶ REGISTER READ AND WRITE CONTROL ................15 Copyright ©2012–2022,Chengdu Ebyte Electronic Technology Co.,Ltd... - Page 3 EFLOW TEMPERATURE .................................. 26 13.2 R EFLOW WELDING DIAGRAM CHAPTER XIV OTHER RECOMMEND MODE ....................26 CHAPTER XV ANTENNA GUIDANCE ......................27 CHAPTER XVI BATCH PACKAGING ......................28 REVISE HISTORY ............................28 ABOUT US ..............................29 Copyright ©2012–2022,Chengdu Ebyte Electronic Technology Co.,Ltd...
-
Page 4: Disclaimer And Copyright Notice
Chengdu Ebai Electronic Technology Co., Ltd. does not guarantee that the content of this manual is completely free from error, and all statements, information and recommendations in this manual do not constitute any express or implied warranty. Copyright ©2012–2022,Chengdu Ebyte Electronic Technology Co.,Ltd... -
Page 5: Chapter I Product Overview
Chapter I Product overview 1.1 Product introduction The E610-433T30S is a high speed continuous transmission 433M wireless data transmission module developed by Ebest, with built-in high performance single chip microcomputer and wireless transceiver chip. Operating in 410 to 441MHz band (default 433MHz), transmit power 30dBm. -
Page 6: Chapter Ii Specification Parameters
There is a risk of burnout with 5V TTL level Emission current mA 1000 Instantaneous power consumption Receiving current Sleep current Software shutdown Working Industrial grade -40 ~ +85 ℃ temperature Storage Industrial grade -40 ~ +125 ℃ temperature Copyright ©2012–2022,Chengdu Ebyte Electronic Technology Co.,Ltd... -
Page 7: Hardware Parameters
2400 ~ 230400 Serial baud rate Stamp hole, spacing 2.54mm Packaging way PA+LNA PA + LNA Antenna IPEX-1 Equivalent impedance approximation 50Ω interface Length*width*height Size 40.5*25.0*3.9(±0.1) Weight 5.15(±0.1) Chapter III Size and pin Copyright ©2012–2022,Chengdu Ebyte Electronic Technology Co.,Ltd... - Page 8 NC pin, which should be suspended NC pin, which should be suspended NC pin, which should be suspended NC pin, which should be suspended NC pin, which should be suspended NC pin, which should be suspended Copyright ©2012–2022,Chengdu Ebyte Electronic Technology Co.,Ltd...
-
Page 9: Chapter Ⅳ Recommendation Line Diagram
The wireless serial port module is at TTL level. Please connect to the MCU at TTL level. Some 5V microcontroller may need to add 4 ~ 10K pull-up resistance in TXD and AUX feet of the module. Copyright ©2012–2022,Chengdu Ebyte Electronic Technology Co.,Ltd... -
Page 10: Chapterⅴ Detailed Functions
Chengdu Ebyte Electronic Technology Co.,Ltd E610-433T30S User Manual ChapterⅤ Detailed functions 5.1Fixed point transmission 5.2 Broadcasting transmission Copyright ©2012–2022,Chengdu Ebyte Electronic Technology Co.,Ltd... -
Page 11: Broadcasting Address
5.6.1 Serial port data output indicator To awaken dormant in the external MCU; AUX pin timing diagram when the module serial port sends out data 5.6.2 Radio transmission indication General transmission mode： Copyright ©2012–2022,Chengdu Ebyte Electronic Technology Co.,Ltd... -
Page 12: The Module Is Being Configured
"T2" in the figure represents the initialization of RF chip configuration parameters (the initialization time is about 500ms)； During the initialization of the microcontroller, the AUX pin will pull down momentarily due to the configuration of GPIO peripherals, as shown in the figure below： Copyright ©2012–2022,Chengdu Ebyte Electronic Technology Co.,Ltd... -
Page 13: Module Mode Switching Process
If AUX is always on high, then the mode switch takes effect immediately. When the user goes from mode 3 (sleep mode) to another mode or during reset, the module will reset the user parameters, during which AUX output is low. Copyright ©2012–2022,Chengdu Ebyte Electronic Technology Co.,Ltd... -
Page 14: Chapter Vi Working Mode
MCU to sleep immediately. The module will automatically send out all the user data wirelessly and enter hibernation within 1ms； Thus saving MCU working time and reducing power consumption. Copyright ©2012–2022,Chengdu Ebyte Electronic Technology Co.,Ltd... -
Page 15: Continuous Transmission Mode (Mode 0)
M0 = 0，M1 = 1，User configuration Pattern (Mode 2) Transceive Only remote configuration commands can be fired. Receive Only remote configuration instruction response is received. Configuration Users can access registers to configure module status. Copyright ©2012–2022,Chengdu Ebyte Electronic Technology Co.,Ltd... -
Page 16: Deep - Sleep Mode （Mode 3
Return: C1 00 04 12 34 00 61 Instruction: C2 + start address + length + parameter Set temporary Response: C1 + start address + length + parameter register Example 1: Set the channel to 0x09 Copyright ©2012–2022,Chengdu Ebyte Electronic Technology Co.,Ltd... -
Page 17: Register Description
* In continuous transmission mode, the serial ports of the 9600（Default） two modules must have the same serial port baud rate is baud rate. 19200 serial port baud rate is Copyright ©2012–2022,Chengdu Ebyte Electronic Technology Co.,Ltd... - Page 18 [0x00] : current environment noise RSSI[0]; Register [0x01] : RSSI when data last received[1]； * Conversion formula： dBm = RSSI/2-154； * Instruction format parsing： Send： C0 C1 C2 C3+ start address + Copyright ©2012–2022,Chengdu Ebyte Electronic Technology Co.,Ltd...
- Page 19 RSSI strength Read/w byte to indicate the signal REG3 strength when the data is rite received； * Conversion formula：dBm = RSSI/2-154。 Transmission way Applicable only to general transmission mode； Transparent transfer (default) Copyright ©2012–2022,Chengdu Ebyte Electronic Technology Co.,Ltd...
-
Page 20: Factory Default Parameters
Restore factory default parameter instruction：C0 00 09 00 00 00 40 00 2E 00 00 00 Air speed Serial port Modue mode Frequency address channel Baud rate Power rate format E610-433T30S 433MHz 0x0000 0x2E 0.5kbps 9600 30dbm Copyright ©2012–2022,Chengdu Ebyte Electronic Technology Co.,Ltd... -
Page 21: Chapter Ⅷ Using The Trunk Networking Mode
Configuration as shown in the figure: Data sent by node 1 can be received by nodes 2 and 4, and data sent by nodes 2 and 4 can also be received by node 1. Copyright ©2012–2022,Chengdu Ebyte Electronic Technology Co.,Ltd... -
Page 22: Chapter Ix Describes The Configuration Of The Upper Computer
Chapter IX describes the configuration of the upper computer The following figure shows the display interface for configuring the upper computer on the E610-433T30S. Users can switch to the command mode by using M0 and M1 to quickly configure and read parameters on the upper computer. -
Page 23: Chapter X Upgrade Firmware
Upgrade mode 2: The module is powered off first, and then powered on after short-connecting AUX and GND pins of the module (maintain short-connecting for at least one second before releasing). The module automatically enters the upgrade mode, and then download the firmware using the configuration tool. Copyright ©2012–2022,Chengdu Ebyte Electronic Technology Co.,Ltd... -
Page 24: Chapter Xi Hardware Designing
When the module is installed inside the housing, the antenna can be extended to the outside of the housing using a good quality antenna extension cable； The antenna must not be installed in the metal shell, which will greatly reduce the transmission distance. Copyright ©2012–2022,Chengdu Ebyte Electronic Technology Co.,Ltd... -
Page 25: Chapter Xii Faq
Power not ideal also may cause garbled, be sure to guarantee the reliability of the power supply; Extension wire, feeder quality is poor or too long, will also cause high bit error rate. Copyright ©2012–2022,Chengdu Ebyte Electronic Technology Co.,Ltd... -
Page 26: Chapter Xiii Welding Instruction
Cooling slope（Tp~TL） 6℃/seconds，max 6℃/seconds，max The time from room temperature to peak 6mins，max 8 mins，max temperature ※The peak temperature (Tp) tolerance of the temperature curve is defined as the user's upper limit Copyright ©2012–2022,Chengdu Ebyte Electronic Technology Co.,Ltd... -
Page 27: Reflow Welding Diagram
2.4G 21*36 E34-2G4D20D nRF24L01+ 2.4G 21*36 E34-2G4H27D nRF24L01+ 2.4G 21*36 E34-2G4D27D nRF24L01+ 2.4G 21*36 E70-433T14S2 CC1310 433M 14*20 E70-433T14S CC1310 433M 16*26 E70-433T30S CC1310 433M 24*38.5 E70-900T14S2 CC1310 868M/915M 14*20 E70-900T14S CC1310 868M/915M 16*26 Copyright ©2012–2022,Chengdu Ebyte Electronic Technology Co.,Ltd... -
Page 28: Chapter Xv Antenna Guidance
Small suction cup Suker TX433-XPL-100 433M SMA-J antenna, Antenna cost-effective Suker Neutral sucker TX433-XP-200 433M SMA-J Antenna antenna, low loss Suker Large suction cup TX433-XPH-300 433M SMA-J Antenna antenna, high gain Copyright ©2012–2022,Chengdu Ebyte Electronic Technology Co.,Ltd... -
Page 29: Chapter Xvi Batch Packaging
Chengdu Ebyte Electronic Technology Co.,Ltd E610-433T30S User Manual Chapter XVI Batch packaging Revise History Version Revise date Revise notes maintainer 2022-12-15 Initial version Ning Copyright ©2012–2022,Chengdu Ebyte Electronic Technology Co.,Ltd... -
Page 30: About Us
E610-433T30S User Manual About us Company Sales Hotline: 4000-330-990 Tel: 028- 61543675 Technical support: support@cdebyte.com Official website: https://www.es-ebyte.com/ Company Address: Building B5, No. 199, West District Avenue, High-tech West District, Chengdu City, Sichuan Province Copyright ©2012–2022,Chengdu Ebyte Electronic Technology Co.,Ltd...