9.3 BER(B ............................... 14 RROR IS HIGH 10 PRODUCTION GUIDANCE ........................14 11 E62 SERIES ..............................15 12 ANTENNA RECOMMENDATION ......................15 13.PACKAGE FOR BATCH ORDER ......................16 REVISION HISTORY ............................. 17 ABOUT US ................................ 17 Chengdu Ebyte Electronic Technology Co,;Ltd...
Chengdu Ebyte Electronic Technology Co,;Ltd E62-433T30D user manual 1. Overview 1.1 Introduction E62-433T30D is a full-duplex wireless transceiver module with TTL level output, operates at 425-450MHz (default: 433MHz), transparent transmission available. Module features FHSS (Frequency-Hopping Spread Spectrum). During the transmitting...
Chengdu Ebyte Electronic Technology Co,;Ltd E62-433T30D user manual Health care products; Advanced Meter Reading Architecture(AMI); Automotive industry applications. 2. Specification and parameter 2.1 2.1 Limit parameter Main parameter Performance Remarks Min. Max. Power supply(V) Voltage over 5.5V will cause permanent damage to module Blocking power(dBm)...
Chengdu Ebyte Electronic Technology Co,;Ltd E62-433T30D user manual Input Work with M1 to decide 2 working modes of module (not suspended, if (weak pull-up) not used, could be grounded). Module synchronization indication: high level indicates that both sides of communication have been synchronized, and data transmission can be...
Chengdu Ebyte Electronic Technology Co,;Ltd E62-433T30D user manual For some MCU works at 5VDC, it may need to add 4-10K pull-up resistor for the TXD & AUX pin. 5 Function description 5.1 Reset When the module is powered, AUX outputs low level immediately, conducts hardware self-check and sets the operating mode based on user’s parameters.
Chengdu Ebyte Electronic Technology Co,;Ltd E62-433T30D user manual 5.2.3 Notes for AUX Description For function 1 & function 2 mentioned above, the priority should be given to the one with low level output, which means if it meets each of any low level output condition, AUX outputs low level, if none of the low level condition is met, AUX outputs high level.
Chengdu Ebyte Electronic Technology Co,;Ltd E62-433T30D user manual 6.1 Mode switch Remarks The user can decide the operating mode by the combination of M1 and M0. The two GPIO of MCU can be used to switch mode. After modifying M1 or M0, it will start to work in new mode 1 ms later if the module is free. If there are any serial data that are yet to finish wireless transmitting, it will start to work in new mode after the UART transmitting finished.
Chengdu Ebyte Electronic Technology Co,;Ltd E62-433T30D user manual 6.3Configure mode (Mode 1) Type When M0 = 1, module works in mode 1. Transmitting N/A. User can configure the module at baud rate = 9600bps, parity = 8N1. Receiving N/A. User can configure the module at baud rate = 9600bps, parity = 8N1.
User gives the module instruction (HEX format): C3 C3 C3, C3+C3+C3 Module returns its present version number, for example C3 62 xx yy. 62 here means the module model (E62 series); xx is the version number and yy refers to the other module features. 7.4 Reset instruction...
Page 12
Chengdu Ebyte Electronic Technology Co,;Ltd E62-433T30D user manual FHSS The quantity of frequency hopping channel Both sides must keep the same. The nums (default 0AH) more quantity of frequency-hopping channel, the better anti-interference while synchronization time is longer for both sides. Otherwise the less...
Page 13
Chengdu Ebyte Electronic Technology Co,;Ltd E62-433T30D user manual CHAN Communication frequency 00H- 33H,for 425 – 450.5MHz (425M+CHAN*0.5M) When the frequency-hopping quantity default 0AH sets as 1, the module works only at the fixed frequency (425M + CHAN * 0.5M).
Chengdu Ebyte Electronic Technology Co,;Ltd E62-433T30D user manual For example: The meaning of No.3 "SPED" byte: The binary bit of the byte The specific value (user configures) UART parity bit Meaning UART baud rate is 9600 Air data rate is 64k Corresponding hexadecimal 8.
Chengdu Ebyte Electronic Technology Co,;Ltd E62-433T30D user manual weakened. 9 FAQ 9.1 Communication range is too short The communication distance will be affected when obstacle exists. Data lose rate will be affected by temperature, humidity and co-channel interference. ...
About us Technical support: support@cdebyte.com Documents and RF Setting download link: www.ebyte.com Thank you for using Ebyte products! Please contact us with any questions or suggestions: info@cdebyte.com ------------------------------------------------------------------------------------------------------------ Fax: 028-64146160 ext. 821 Web: www.ebyte.com Address: Innovation Center D347, 4# XI-XIN Road,Chengdu, Sichuan, China Chengdu Ebyte Electronic Technology Co,;Ltd...