Speaker Setup - Onkyo HT-RC370 Instruction Manual

Speaker Setup

Main menu
Some of the settings in this section are set automatically
by Audyssey MultEQ
Speaker Setup function
Here you can check the settings made by
Audyssey MultEQ XT Room Correction and Speaker
Setup function, or set them manually, which is useful if
you change one of the connected speakers after using
Audyssey MultEQ XT Room Correction and Speaker
Setup function.
Note
• These settings are not available in either of the following cases:
– a pair of headphones is connected.
– the "Audio TV Out" setting is set to "On"
– "HDMI Control(RIHD)" is set to "On"
you're listening through your TV speakers.
Speaker Settings
If you change these settings, you must run
Audyssey MultEQ XT Room Correction and
Speaker Setup again
If the impedance of any speaker is 4 ohms or more but less
than 6, set the minimum speaker impedance to 4 ohms.
If you bi-amp the front speakers, you must change the
"Speakers Type(Front)" setting
hookup information, see "Bi-amping the Front Speakers"
(➔ page 14).
Note
• When bi-amping is used, the AV receiver is able to drive up to
5.1 speakers in the main room.
• Before you change these settings, turn down the volume.
■
Speaker Impedance
4ohms:
Select if the impedance of any speaker is 4 ohms or
more but less than 6.
6ohms:
Select if the impedances of all speakers are between
6 and 16 ohms.
■
Speakers Type(Front)
Normal:
Select this if you've connected your front speakers
normally.
Bi-Amp:
Select this if you've bi-amped your front speakers.
■
Powered Zone 2
No
Yes:
Zone 2 speakers can be used. (Powered Zone 2
enabled).
En
46
Speaker Setup
® XT Room Correction and
(➔ page 31).
(➔ page 58).
(➔ page 57) and
(➔ page 31).
(➔ page 46). For
Note
• If the "Speakers Type(Front)" setting is set to "Bi-Amp",
Powered Zone 2 cannot be used.
• When the "Powered Zone 2" setting is set to "Yes", the
surround back, front wide and front high speakers cannot be
used.
Speaker Configuration
This setting is set automatically by
Audyssey MultEQ XT Room Correction and Speaker
Setup function (➔ page 31).
With these settings, you can specify which speakers are
connected and a crossover frequency for each speaker.
Specify "Full Band" for speakers that can output low
frequency bass sounds adequately, for example, speakers
with a good sized woofer. For smaller speakers, specify a
crossover frequency. Sounds below the crossover
frequency will be output by the subwoofer instead of the
speaker. Refer to your speaker's manuals to determine the
optimum crossover frequencies. If you set up your
speakers using Audyssey MultEQ XT Room Correction
and Speaker Setup, please make sure manually that any
THX speakers are set to "80Hz(THX)" crossover.
Note
• These settings are not available in either of the following cases:
– a pair of headphones is connected.
– the "Audio TV Out" setting is set to "On"
– "HDMI Control(RIHD)" is set to "On"
you're listening through your TV speakers.
■
Subwoofer
Yes
No
■
Front
Full Band
40Hz to 80Hz(THX) to 100Hz, 120Hz, 150Hz,
200Hz
Note
• If the "Subwoofer" setting is set to "No", the "Front" setting is
fixed to "Full Band".
■
Center , Surround , Surround Back
*1 *1
Full Band
40Hz to 80Hz(THX) to 100Hz, 120Hz, 150Hz,
200Hz
None
■
Front Wide , Front High
*1*2*4
Full Band
40Hz to 80Hz(THX) to 100Hz, 120Hz, 150Hz,
200Hz
None
(➔ page 58).
page 57) and
(➔
*2*3*4
*1*2*4