Table of Contents
Advertisement
Quick Links
QUICK EA-A10
BGA/CSP Rework Station
Operation Manual
Thank you for purchasing our BGA/SMD Rework System. The system is exclusively designed for reworking
and soldering SMD component. Please carefully read this manual before operating the system. Store this
manual in a safe, easily accessible place for future reference.
Advertisement
Table of Contents
Related Manuals for Quick EA-A10
Summary of Contents for Quick EA-A10
- Page 1 QUICK EA-A10 BGA/CSP Rework Station Operation Manual Thank you for purchasing our BGA/SMD Rework System. The system is exclusively designed for reworking and soldering SMD component. Please carefully read this manual before operating the system. Store this manual in a safe, easily accessible place for future reference.
-
Page 2: Table Of Contents
QUICKEA-A10 OPERATION MANUAL 目 录 3. The Unit is Supplied with ..........................2 4. Safety Instructions ............................3 5. Specifications and Technical Parameters ....................3 5.1 Specifications ............................3 5.2 Technical Parameter ..........................4 HED： the position of the top heater（UP-DOWN-UNKN） ................4 ALG：... - Page 3 QUICK EA-A10 OPERATION MANUAL 1. Summary Thank you for using QUICK BGA EA-A10 Rework System. This system, have increase base heating power to original system , which adopts micro-processor control and infrared sensor technology to do soldering and de-soldering to surface mount components safely and accurately, increases bottom heating power based on the original one.
-
Page 4: The Unit Is Supplied With
Support fixed knob Bottom hot wind heating Bottom infrared preheat 3. The Unit is Supplied with Please check whether the following parts are included and intact. * QUICK EA-A10 Main Unit 1 pcs * PC（optional） 1 pcs * QUICK EA-A10 Operation Manual... -
Page 5: Safety Instructions
QUICK EA-A10 OPERATION MANUAL 4. Safety Instructions Note: For the safety of the system and operator, please read this manual carefully before operating the unit. Please note that the unit is suitable for soldering and de-soldering of electronic components. Note: Top and bottom infrared heater and sirocco nozzle will be very hot during working, so explosive and combustible object or gas and solvent is strictly prohibited in working areas, also please don’... -
Page 6: Technical Parameter
Check the package of the equipment is good or not. Take out the QUICK EA-A10 from the package and place it on the solid working desk. Check every unit is good or not according to the packing list. If not, please replace the unit from our company or agents in time. -
Page 7: Parts Instruction
QUICK EA-A10 OPERATION MANUAL 7. Parts Instruction 7.1 Sensor The system has five K-type sensors for checking the temperature on the PCB, such as the temperature of BGA surface, bottom temperature of the PCB, real temperature of the tin ball. And these values can show on the LCD. Besides, users can select the sensors during KT1-KT5. -
Page 8: Keys Instructions
QUICK EA-A10 OPERATION MANUAL rocker onward or backward, the PCB fixture will do the corresponding movement, onward or backward. If do not press the key on the top of the rocker and swing the rocker, the pad sucking the chip can do turn 360°. -
Page 9: Aligning Arm Instruction
QUICK EA-A10 OPERATION MANUAL Key name Function description Control magnify and reduce of picture, 1~8 zoom ratio in all; Zoom Rotate clockwise（+） ，picture magnification, anticlockwise（-） ，reduction Camera focus key Focus Rotate clockwise (+） ，focus magnification,， anticlockwise（-） ， reduction Top white light TOP-LIGHT Rotate clockwise （+）... -
Page 10: 8、Technology Process
QUICK EA-A10 OPERATION MANUAL 8、Technology Process Technology Process contain: solder and desolder. The soldering process includes suck, alignment and soldering. The de-soldering process includes laser alignment and de-soldering. 8.1 Process of Sucking the Chip CAMERA key Click The alignment arm is out. -
Page 11: Solder Flow Of Chip
QUICK EA-A10 OPERATION MANUAL 8.2 solder flow of chip In operation interface,select solder Select flow The moving arm moves downwards after the alignment arm back to Press “start” origin. bottom pre-heater （or press “START” in face ban） comes to heat up and the TIR will change with real time. -
Page 12: Soldering Process
QUICK EA-A10 OPERATION MANUAL 8.3 De-soldering Process Note: please check the flow type “deso” before running the de-soldering process. The counterpoint in the middle of desolder chip Select desolder in software Select flow in software interface The moving arm will... -
Page 13: 9、Description Of The Process
QUICK EA-A10 OPERATION MANUAL 9、Description of the process Note: The top and bottom heater will be very hot during working, so please don’ touch the hot surface of the parts. 9.1 place height and suck height Place height: after setting one time, place height be save and memory, Do not adjust focus every times for the same BGA chip.(the next time effect which parameter save to current flow) -
Page 14: Desolder Technology
QUICK EA-A10 OPERATION MANUAL 9.3 Desolder technology Note: desolder technology flow the same as solder technology flow, only select desolder in BGA software. Place need solder PCB to PCB studdle（If PCB irregular, can use dysmorphism support）. Screw fixed knob of PCB holder. -
Page 15: Equipment Maintenance
2. Take the suction pad out of suction nozzle downwards, and install a new one in opposite direction. Note: QUICK BGA EA-A10 is precise equipment. Please don’t make any changes on it. Otherwise the precision of this equipment will be affected. -
Page 16: 11、Quicksoft Brief Instruction
QUICK EA-A10 OPERATION MANUAL 11、QUICKSOFT brief instruction 11.1 operation interface 1. Operation interface: this interface reaction executive condition of flow , we can real-time operate by this interface. 2. parameter of operation interface, be setting from “parameter testing interface”, in operation interface do not need setting. -
Page 17: Counterpoint Operation Interface
QUICK EA-A10 OPERATION MANUAL Working area: contain every working button “heat arm up”, “heat arm down”、 “dissipation open/dissipation close” 、 “place component ” 、 “start” 、 “stop” 。 11.2 counterpoint operation interface We can complete total counterpoint operation by counterpoint operation interface , contain focus, magnify reduce, suck component, etc. -
Page 18: Parameter Testing Interface
QUICK EA-A10 OPERATION MANUAL “interior”; again click aligning arm, it will move to external ,the location state change to “external”. Exit : exit “counterpoint operation ”interface, enter “operation interface”, current state have no change. When working area display aligning arm in ,then status bar location of aligning arm: external;... -
Page 19: Curve Analysis Display
QUICK EA-A10 OPERATION MANUAL After edit parameter in parameter setting display, in“flow edit display”input flow name, appropriate nozzle size, select flow technology curve is “desolder”、or “solder”. And then click “parameter save”、 “save curve”， can save current parameter and flow curve. - Page 20 QUICK EA-A10 OPERATION MANUAL Password setting: can set “enter password” and “parameter protect” two type password. The people who obtain enter password can operation this software, but no parameter modify power. The people who obtain parameter protect can operation this software, and modify parameter.
- Page 21 Changzhou Quick Soldering Co., Ltd Add: No.11, FengXiang Road, Wujin High-Tech Industrial Development Zone, Jiangsu, China Tel: 86-519-86225678 Fax: 86-519-86558599 Zip code: 213167 Website: www.quick-global.com...