Table of Contents
Advertisement
Quick Links
QUICK2035
BGA Rework System
Operation Manual
Thank you for purchasing our Rework System. The system is exclusively designed for reworking and
soldering SMD component. Please carefully read this manual before operating the system. Store this manual
in a safe, easily accessible place for future reference.
Advertisement
Table of Contents
Related Manuals for Quick QUICK2035
Summary of Contents for Quick QUICK2035
- Page 1 QUICK2035 BGA Rework System Operation Manual Thank you for purchasing our Rework System. The system is exclusively designed for reworking and soldering SMD component. Please carefully read this manual before operating the system. Store this manual in a safe, easily accessible place for future reference.
-
Page 2: Table Of Contents
Table of Contents 1. Summary…………………………………………………………………………………………………1 2. Specification and Technical Parameter……………………………………………………………………1 2.1 Specification…………………………………………………………………………………………1 2.2 Technical Parameter…………………………………………………………………………………2 3. Product picture……………………………………………………………………………………………3 4. Safety Instruction…………………………………………………………………………………………3 5. Install the unit and use parts ……………………………………………………………………………4 5.1 Place the unit…………………………………………………………………………………………4 5.2 Check the unit………………………………………………………………………………………4 5.3 Connect the unit………………………………………………………………………………………4 5.4 Using parts……………………………………………………………………………………………5 6. -
Page 3: Specification And Technical Parameter
The infrared heating tube of QUICK2035, with a uniform and safe heating and power systems and the flexibility necessary for the large heat capacity of PCB and other high temperature requirements (lead-free soldering), etc. -
Page 4: Product Picture
OPERATION MANUAL 2.2 Technical Data TL: Melting temperature of solder T1: Heat preservation starting temperature of reflow soldering T2: Heat preservation ending temperature of reflow soldering T3: Peak value temperature of soldering and de-soldering T0: Valve temperature: The lowest temperature of bottom heater when top heater heats up. T0<TB TB: The set temperature of bottom heater Tb: The real time temperature value of bottom heater TC: The real time temperature value of top heater... -
Page 5: Place The Unit
5. Install the Unit and Adjust Parts 5.1 Place the Unit Unwrap the packing of the unit, then take it out and put it on the solid level worktable. Put QUICK2035 main unit on the base plate. 5.2 Check the Unit Please check whether the following parts are in good condition and they aren’t missed. -
Page 6: Keyboard And Parameter Setting
OPERATION MANUAL 5.4 PCB Fixture PCB Lock Knob Fore-and-aft inching crew Supporting bar at the bottom of anti-collapse 1. The fore-and-aft removable distance is bigger than 100mm, and the removable maximum distance is about 400mm from left to right. 2. Maximum height of 92mm can be used. Dimensions:700（L）* 580(W) * 170(H)mm 3. -
Page 7: Parameter Setting
OPERATION MANUAL upward or downward of cursor and increase or decrease of number. key “ During the soldering or de-soldering period, also top IR heater haven’t yet started to heat up, +” and key “-”are used for controlling movement upward or downward of top IR heater. That is to say, “... - Page 8 OPERATION MANUAL password: *** password: 0** Press “-” Press “SET” select: 0 select: 0 password: 0** password: 00* Press “-” Press “SET” select: 0 select: 0 password: 00* Press “-” password: 000 Press “OK” select: 0 select: 0 Saving Password! Any key return Password to complete：...
-
Page 9: C-1. Modify Parameter Of Working Flow
OPERATION MANUAL password: *** password: *** Press “+” Press “OK” Step③ Step④ select: 0 select: 1 password: *** select: 1 When carry on the forth step (Step④), if press “SET” key, you can browse and modify parameter of this flow, shown as C-1 item. After finishing modifying of working flow 1, if you want to modify the next working mode, operate as C item shows;... - Page 10 OPERATION MANUAL T0 is the valve temperature for bottom heater required by top heater when it heats up. Also it is the first temperature of this technics process. When the work flow begins, the bottom heater starts to heat up. After reaching the T0, the top heater begins to heat up.
- Page 11 OPERATION MANUAL controlling. In parameter modifying, use the “↑” and “↓” key to set the value. Password It is used for setting password. It is designed for preventing the equipment unnecessary or non-authorized change. When it is set to “000”, the password protecting is useless. The password is used for all flows and it can be useful and useless in each flow.
- Page 12 OPERATION MANUAL S1: 060s S1: 060s Press “OK” Press “-” T2: 160℃ T2: 160℃ Press “SET” Press “SET” T2: 160℃ T2: 160℃ S2: 030s S2: 030s T2: 160℃ T2: 160℃ Press “OK” Press “+”two time S2: 030s S2: 050s Press “-” Press “-”...
-
Page 13: Modify Laser Alignment Mode
OPERATION MANUAL Press “-” Press “-” T0: 090℃ unit:℃ unit:℃ sense: IR Senser: IR type: desolder D. Modify Laser Alignment Mode For instance: Modify the laser alignment mode and set it to “on”. Press “-” type: desolder Press “SET” select: 1 laser: off type: desolder type: desolder... -
Page 14: Technics Instruction
OPERATION MANUAL TC: ***℃ Tb: ***℃ T sense error ! If the bottom sensor is broken, it displays: TC: ***℃ Tb: ***℃ B sense error ! When happening above status, user must stop operating. If TC is more than 275 during wor king, the system will also exit the process and back to the initial state. -
Page 15: De-Soldering Technics
OPERATION MANUAL F. Press “BEGIN” key and the system start to work, perform content of selected flow. 5. The window will show series of setting temperatures and the current temperature of Tb and TC during working, and indicate when it reaches T0, T1, T2, T3 and TL. S1, S2 and S3 are counted down and user can know about the setting value clearly. -
Page 16: Turn Off The System
OPERATION MANUAL 8. Turn off the system Please turn off power switch of each part and pull out power plug when not using it. 9. System Maintenance Remark: For ensuring reliable function and maintenance of equipment, please use parts provided by original factory. Note: After cutting off the power supply, the housing is still very hot, so please don’t use any dangerous or combustible solvent to clean it.
Need help?
Do you have a question about the QUICK2035 and is the answer not in the manual?
Questions and answers