Related Manuals for Quick 862DA+
Summary of Contents for Quick 862DA+
- Page 1 862DA+/862DW+ SMD REWORK STATION Instruction Manual Thank you for purchasing our products. Please keep the Instruction manual properly for future reference.
-
Page 2: Table Of Contents
Contents 1. Safety Instruction......................1 2. Product Overview......................2 3. Product Features......................2 4. Product Specifications....................3 5. Display and Function Descriptions................3 5.1Dimensions....................... 3 5.2 Part Descriptions.................... 4 5.3 Button Descriptions..................4 5.4 Main Menu....................... 5 6. Installation and Connection..................5 6.1 Hot Air Section....................5 6.2 Connection.......................6 7. -
Page 3: Safety Instruction
1. Safety Instruction CAUTION During the installation and use of the product, you need to observe the electrical safety regulation of location. Please power off the product during disassembly. If the product is not working properly, please contact the supplier or manufacture, do not disassemble or modify without notice. -
Page 4: Product Overview
2. Product Overview This product is suitable for desoldering and soldering of various components, such as SMD, SOP, SOG, etc. It can be used in many occasions, such as heat shrinkage, drying, paint removal, adhesive removal, thawing, preheating, disinfection, glue welding, etc. -
Page 5: Product Specifications
4. Product Specifications Product model 862DA+ 862DW+ Display Power 1000W Working voltage AC 110V/220V/230V Steel tube Direct wind Cyclone Temperature range 100℃～500℃/ 212℉ ～932 ℉ Range of air volume 1～120 Class Airflow 50L/min（Max） Dimensions(L×W×H) 180*210*130.6mm Weight About 2.6Kg 5. Display and Function Descriptions 5.1Dimensions Unit: mm... -
Page 6: Part Descriptions
5.2 Part Descriptions Serial Part Names Number Main unit Hot air handle Handle holder Power switch 5.3 Button Descriptions Button Functions 1. Press •to ••• to switch to channels 1 to 3. • 2. Press • and ••at the same time to set the prompt tone. ••... -
Page 7: Main Menu
5.4 Main Menu Symbol Function Heating state Display: button tone and alarm prompt ton e are enabled No display: button tone and alarm tone ar e disabled Real Temp Real-time temperature 6. Installation and Connection 6.1 Hot Air Section The handle holder must be installed when the machine is used for the first time, as shown in the picture on the right. -
Page 8: Connection
6.2 Connection Connect the external power supply, turn on the station, and it starts to work. 7. Temperature and Air Volume and Channel Setup 7.1 Temperature Setup Press + or - to increase or decrease the temperature by 1 ° C, and hold down + or - to rapidly increase or decrease the temperature. -
Page 9: Operation
8. Operation If the initial password is 000, the system is unlocked, and you can set parameters and select channels. 1) Place the hot air rework station on the table, select an appropriate air nozzle, and try to use a large diameter air nozzle (refer to "14.1 Installation and Removal of air nozzle"), then place the handle on the holder. - Page 10 Note: 1) Enter the password twice 2) If the next password is not the same, the setting of password is not successful and the window displays “no”. After that, the station comes into work state and the password is still the former one. 3) If the next password is the same, the setting of password is successful and the unit displays “SAV_ _ _”...
-
Page 11: Sound Setup
10. Sound Setup 1) Press the “•” and “••” for three seconds at the same time in the working mode or in the sleeping mode. It can switch on or off the sound. 2) When the LCD displays “ ”, the station has key sound and alarm sound. When not displaying “... -
Page 12: Replacement Of The Heater
2) Enter the calibration mode: When the temperature is stable, press the keys “ ” and • “ ” at the same time for 7seconds, and then the LCD will display “cal” about two ••• seconds and the station will enter the temperature calibrating mode. Input the testing temperature after the hundreds digit twinkling. -
Page 13: Steps Of Replacing The Heater
13.2 Steps of replacing the Heater 1) Install the heater on the ⑥ Handle components, and the square column on the heating body is facing the square hole on the wiring seat; The square is opp osite the terminal bl 2) Cover ①... -
Page 14: Nozzles
Nozzles... -
Page 15: Consumable List
16. Consumable List Product model 862DA+ 862DW+ A1124 A1124 Nozzle A1130 A1130 A1300 A1300 Heater TR3-H-ZZ-01-220V TR3-H-ZZ-01 -220V Steel pipe TR3-P-09H TR3-P-08H Mica paper ceramic packing Handle 863DA+ TR3-P Holder The handle sheath Pump components Fan module 863DW+ 863DW+ Sucking pad 862DA+ 862DW+...