Advertisement
5.7.
ATTACH THE GARDEN HOSE FIG.8
5.7.1.
Remove the plastic plug from the water inlet pipe of the
machine and screw the water inlet connector onto the water
inlet pipe.
5.7.2.
Connect one end of the garden hose (not supplied) to the
water inlet connector and another end to water source.
WARNING! The appliance is INTENDED to be used at a
‰
temperature above 0°C.
WARNING! Garden hose must be in good condition.
‰
Inner diameter no less than 1/2", length can not be greater than
8m.
5.8.
Connect to mains power.
6. OPERATION
WARNING! During operation appliance must be positioned on firm, stable surface. High pressure hose must not be coiled on the
‰
washer. When operating the machine, it must only be used upright.
WARNING! Check that the supply voltage and frequency correspond to those specified on the appliance data plate. The appliance
‰
should only be connected to a mains power supply via a security breaker (Max.30mA) to cut off the electricity supply in the instance of
a short circuit.
6.1.
START UP FIG.9
6.1.1.
Turn water on. Squeeze trigger for approx. 1 minute until low pressure water flows out, to empty air out of the unit.
WARNING! For use with cold water only.
‰
Note: Before pressing trigger, make sure lock-off switch is in "unlock" position.
6.1.2.
Turn the switch to "ON/I" position, then press trigger.
WARNING! DO NOT start the machine without connecting and turning on the water supply, it may cause damage to high pressure
‰
seals and reduce the service life of pump.
fig.9
6.2.
CLEANING
6.2.1.
Squeeze the trigger, high pressure water flow will come out.
6.2.2.
Rotate Adjustable nozzle collar, fig.9A, to change it from a full fan spray (diagram 1) to a direct stream spray (diagram 2).
Note: Begin with the nozzle 1-2ft away from the surface and approach with caution until it reaches the desired position. Too close
a spray may do harm to the surface.
WARNING! DO NOT connect the machine to water supplies that are dirty, rusty, muddy, or corrosive, including window cleaning
‰
liquids, plant foods, or fertilizers etc.
6.2.3.
When cleaning is finished, release the trigger and turn the switch to "OFF/O" position, then turn off the water supply.
Note: When not in use, make sure Lock-off switch is in "Lock" position.
Note: Using pressure washer after water supply has been turned off, serious damage could occur to the pump and/or motor.
WARNING! Never disconnect high pressure discharge hose from machine while system is pressurized. To de-pressurize, turn switch
‰
off, turn water supply off and squeeze gun trigger 2-3 times.
6.2.4.
Disconnect from mains supply.
6.3.
SAFETY VALVE/PRESSURE LIMITING VALVE
WARNING! DO NOT tamper with or adjust the safety valve setting.
‰
6.3.1.
The safety valve is also a pressure limiting valve. When the gun trigger is released, the valve opens, pressure switch operates, and
the machine automatically shut down. If the gun nozzle is blocked, will cause the machine pressure rises, the safety valve opens, the
pressure switch activates, the machine automatically shuts down.
6.3.2.
Refer to section 7.2 to use a needle to clean the nozzle.
6.4.
GUN SAFETY BUTTON FIG.10
6.4.1.
Operator needs to press the unlock button and then actuate the trigger to release spray.
6.4.2.
When trigger is released, trigger will return to the off position automatically.
6.4.3.
When not using the pressure cleaner, press the lock button to keep from accidentally engaging the high pressure spray.
fig.10
6.5.
HOLDING THE GUN
6.5.1.
Hold the gun correctly to resist kickback forces: one hand on the handle, one on the lance.
© Jack Sealey Limited
fig.8
Original Language Version
fig.9A
PW1860
Issue 1
17/11/2022
Advertisement
