Advertisement
PARTS LIST:
2
Universal Mounting Tubes ( 69'')
4
DS5 Drop Steps
2
Left Plastic End Caps
2
Right Plastic End Caps
2
Front Mounting Brackets
2
Center Mounting Brackets
2
Rear Mounting Brackets
6
Support Bracket
8
Spacers
28
8-1.25mm x 25mm T-Bolts
6
Nut Plates
6
10-1.5mm x 35mm Hex Bolts
6
10-1.5mm x 30mm Hex Bolts
Rear Mounting
Bracket
Center Mounting
Bracket
(2) Universal Mounting Tubes
6
10mm Lock Washers
6
10mm x 34mm x 3mm Flat Washers
12
10mm x 20mm x 2mm Flat Washers
6
10-1.5mm Nylon Lock Nuts
16
8-1.25mm Nylon Lock Nuts
6
8-1.25mm x 35mm Hex Bolts
12
8-1.25mm Hex Nuts
6
8mm x 28mm x 3mm Flat Washers
12
8mm x 24mm x 2mm Flat Washers
18
8mm Lock Washers
12
6-1.00mm Nylon Lock Nuts
12
6-1.00mm x 25mm Hex Bolts
24
6mm x 22mm x 2mm Flat Washers
(6) Support Brackets
(2) Front Mounting
Brackets
(4) DS5 Drop Steps
Page 1 of 6
DS5 RUNNING BOARD
07-18 Wrangler JK 4 Door
Rear Mounting
Bracket
Center Mounting
Bracket
5/19/22 (SL)
Advertisement
Table of Contents
Subscribe to Our Youtube Channel
Related Manuals for Steelcraft DS5
Summary of Contents for Steelcraft DS5
- Page 1 6mm x 22mm x 2mm Flat Washers (6) Support Brackets Rear Mounting Rear Mounting Bracket Bracket Center Mounting Bracket Center Mounting (2) Front Mounting Bracket Brackets (2) Universal Mounting Tubes (4) DS5 Drop Steps Page 1 of 6 5/19/22 (SL)
- Page 2 10). Each front channel should have (4) T-bolts, which corresponds to the holes on the DS5 Drop Steps. 7. Attach the DS5 Drop Steps to the Universal Mounting Tube. Each DS5 Drop Step uses (2) 8mm Plate Washers and (4) 8mm Nylon Lock Nuts, (Figure 11—12). Do not tighten hardware. While the hardware is not tightened, the Drop Steps will slide along the length of the channels.
- Page 3 DS5 RUNNING BOARD 07-18 Wrangler JK 4 Door (Fig 2B) 10mm Nut Plate Front (Fig 1) Passenger/Right mounting locations (Fig 2A) Passenger/Right front mounting location (Models without threaded insert shown) 10mm x 35mm Hex Bolt 10mm Lock Washer 10mm x 34mm Flat Washer...
- Page 4 DS5 RUNNING BOARD 07-18 Wrangler JK 4 Door 10mm x 30mm Hex Bolt (2) 10mm x 20mm Flat Washers 10mm Nylon Lock Nut (Fig 6) Attach (1) Support Bracket to the Front Mounting Bracket Passenger/Right Side Installation Pictured Fig 7B...
- Page 5 DS5 RUNNING BOARD 07-18 Wrangler JK 4 Door Front Channels (Fig 10) Insert T-bolts into the Front channels on the universal mounting tube. (2) 8mm Nylon Lock Nuts (1) 8mm Plate Washer (Fig 11) Attach the Drop Steps to the front channels of the Universal Mounting Tube.
- Page 6 DS5 RUNNING BOARD 07-18 Wrangler JK 4 Door (2) 8mm Flat Washers (2) 8mm Lock Washers (2) 8mm Hex Nuts (Fig 14) Attach the Universal Mounting Tube to the Mounting Brackets. Page 6 of 6 5/19/22 (SL)
Need help?
Do you have a question about the DS5 and is the answer not in the manual?
Questions and answers