Download Print this page

Steelcraft Elevation Bull Nose Front Bumper Installation Instructions Manual

2009-14 ford f150

Advertisement

Quick Links

PARTS LIST:
1
Front Bumper Assembly
1
Driver/Left Frame Mounting Bracket
1
Passenger/Right Frame Mounting Bracket
1
Driver/Left Top Support Bracket
1
Passenger/Right Top Support Bracket
1
Driver/left LED Light Brackets
1
Passenger/right LED Light Brackets
1
Winch Access Cover
5
6mm Button Head Combo Bolt
1
4mm Wrench
2
Plastic Plugs for license plate mount
2
12mm Double Nut Plates
2
12-1.75mm x 160mm Hex Bolts
Passenger/right
Support Bracket
Passenger/Right
Frame Mounting
Bracket
PROCEDURE:
REMOVE CONTENTS FROM BOX. VERIFY ALL PARTS ARE PRESENT. READ INSTRUCTIONS
CAREFULLY BEFORE STARTING INSTALLATION. BUMPER IS HEAVY, ASSISTANCE IS HIGHLY
RECOMMENDED TO AVOID POSSIBLE INJURY OR DAMAGE TO THE VEHICLE.
1. Remove the license plate and bracket. Open the hood and remove the hardware attaching the hood
release lever to the steel bracket attached to the back of the bumper, (Figure 1). Also remove the
screws attaching the back of the plastic facia to the hood release bracket. On models with factory fog
lights, unplug both lights and release the wiring harness from the clips attached to the back of the
bumper. Move harness away from bumper.
2. Place blocks or jack stands under the front bumper to support it during mounting bolt removal. Once the
bumper has been safely supported, remove the (2) large hex nuts from the back of each bumper
bracket, (Figure 2). WARNING! Assistance is required to hold the bumper in place during bolt removal
to prevent the bumper from falling. Carefully slide the bumper off over the tow hooks, if equipped. Next,
remove the air dam from the bottom of the frame, if equipped, (Figure 3).
(2) Double Nut Plates
Winch Tray
ELEVATION BULL NOSE FRONT BUMPER
24
12-1.75mm x 50mm Hex Bolts
48
12mm x 37mm x 3mm Flat Washers
4
12mm Lock Washers
22
12-1.75mm Nylon Lock Nuts
2
8-1.25mm x 25mm Hex Bolt
2
8-1.25mm x 16mm Hex Bolt
6
8mm x 24mm x 2mm Flat Washer
4
8mm Lock Washer
2
8mm Hex Nut
6
6mm x 25mm Hex Bolts
12
6mm x 18mm x 1.6 Flat Washers
6
6mm Nylon Lock Nuts
Left/Right "L"
LED Brackets
(2) License Plate
Plugs
Page 1 of 7
2009-14 FORD F150
Driver/left Top
Support Bracket
Driver/Left Frame
Mounting Bracket

Advertisement

loading
Need help?

Need help?

Do you have a question about the Elevation Bull Nose Front Bumper and is the answer not in the manual?

Questions and answers

Subscribe to Our Youtube Channel

Summary of Contents for Steelcraft Elevation Bull Nose Front Bumper

  • Page 1 ELEVATION BULL NOSE FRONT BUMPER 2009-14 FORD F150 PARTS LIST: Front Bumper Assembly 12-1.75mm x 50mm Hex Bolts Driver/Left Frame Mounting Bracket 12mm x 37mm x 3mm Flat Washers 12mm Lock Washers Passenger/Right Frame Mounting Bracket Driver/Left Top Support Bracket 12-1.75mm Nylon Lock Nuts...
  • Page 2 ELEVATION BULL NOSE FRONT BUMPER 2009-14 FORD F150 3. Remove the driver side tow hook, (if equipped), from the bottom of the frame. Leave the factory double nut plate inside the frame, (Figure 4). On models without tow hook, insert (1) Double Nut Plate into the open end of the frame, (Figure 4).
  • Page 3 ELEVATION BULL NOSE FRONT BUMPER 2009-14 FORD F150 13. Level and adjust the bumper and fully tighten all 12mm hardware to 65-70ft-lbs. Access hardware at the top of the Mounting Bracket through the removable access cover on the top of the Bumper. NOTE: If additional adjustment is required, loosen Frame Bracket Hardware and adjust Bracket as necessary.
  • Page 4 ELEVATION BULL NOSE FRONT BUMPER 2009-14 FORD F150 Driver Side Installation Pictured Bumper flange Double Nut Plate on frame Front (Fig 4) Models without tow hook, slide Double Nut Plate into open end of frame. Models with tow hook, remove tow hook...
  • Page 5 ELEVATION BULL NOSE FRONT BUMPER 2009-14 FORD F150 Driver Side Installation Pictured Front (2) 12mm x 50mm Hex Bolts (2) 12mm Lock Washers (2) 12mm Flat Washers (2) 12mm x 50mm Hex Bolts (2) 12mm Lock Washers (2) 12mm Flat Washers...
  • Page 6 ELEVATION BULL NOSE FRONT BUMPER 2009-14 FORD F150 Driver Side Installation Pictured IMPORTANT: Air intake shroud on Ecoboost equipped models may require cutting to clear the Winch Tray. (3) 12mm x 50mm Hex Bolts (6) 12mm Flat Washers (3) 12mm Nylon Lock Nuts...
  • Page 7 ELEVATION BULL NOSE FRONT BUMPER 2009-14 FORD F150 Driver Side Installation Pictured (3) 12mm x 45mm Hex Bolts (6) 12mm Flat Washers (3) 12mm Nylon Lock Nuts Bumper flange on frame (Fig 16) Driver/left side of Bumper attached to Frame Bracket (pictured from behind bumper)