Steelcraft DS5 Manual

Running board 19-22 wrangler jl 4 door

Advertisement

Quick Links

PARTS LIST:

2
Universal Mounting Tubes ( 69'')
2
Left Plastic End Caps
2
Right Plastic End Caps
4
DS5 Drop Steps
2
Front Mounting Brackets
2
Center Mounting Brackets
2
Rear Mounting Brackets
2
Front Support Brackets
4
Center & Rear Support Brackets
8
Spacers
28
T-Bolts
6
10-1.5mm x 30mm Hex Bolts
Front Mounting
Center Mounting
Brackets
Brackets
(2) Universal Mounting Tubes

PROCEDURE:

REMOVE CONTENTS FROM BOX. VERIFY ALL PARTS ARE PRESENT. READ INSTRUCTIONS
CAREFULLY. ASSISTANCE IS RECOMMENDED.
1. Start installation on the Passenger/Right front of the of the vehicle. Find the front threaded insert
located in between the first pair of holes along the pinch weld, (Figure 1).
2. Select the Front Support Bracket. IMPORTANT: Use the illustration above to help identify the correct
Support Bracket. Attach the Support Bracket to the pinch weld using (2) 6mm Hex Bolts, (4) 6mm Flat
Washers and (2) 6mm Nylon Lock Nuts, (Figure 2 & 4). NOTE: Insert Bolts from the outside of the
pinch weld.
3. Select the Passenger/Right Front Mounting Bracket. IMPORTANT: Use the illustration above to
properly identify the Mounting Bracket. Attach the Mounting Bracket to the threaded insert using (1)
8mm Hex Bolt, (1) 8mm Lock Washer and (1) 8mm Flat Washer, (Figure 3—4). Do not tighten
hardware. Attach the Support Bracket to the Mounting Bracket with (1) 10mm Hex Bolt, (2) 10mm Flat
Washers and (1) 10mm Nylon Lock Nut, (Figure 3—4). Do not tighten hardware.
4. Move to the center mounting location and locate the threaded insert and pair of holes in the pinch weld,
(Figure 5). Repeat Steps 2 & 3 to attach the Center Mounting Bracket and (1) Center/Rear Support
Bracket, (Figures 7—9). Do not tighten hardware.
6
10-1.5mm Nylon Lock Nuts
12
10mm x 24mm x 2.2mm Flat Washers
16
8-1.25mm Nylon Lock Nuts
6
8-1.25mm x 35mm Hex Bolts
12
8-1.25mm Hex Nuts
6
8mm x 28mm x 3mm Flat Washers
12
8mm x 24mm x 2mm Flat Washers
18
8mm Lock Washers
12
6-1.00mm Nylon Lock Nuts
12
6-1.00mm x 25mm Hex Bolts
24
6mm x 22mm x 2mm Flat Washers
(2) Front Support Brackets
(4) Center & Rear Support Brackets
(2) Rear Mounting Brackets
(4) DS5 Drop Steps
Page 1 of 8
DS5 RUNNING BOARD
19-22 Wrangler JL 4 Door
Front Mounting
Brackets
Center Mounting
Brackets
5/19/22 (SL)

Advertisement

Table of Contents
loading
Need help?

Need help?

Do you have a question about the DS5 and is the answer not in the manual?

Questions and answers

Summary of Contents for Steelcraft DS5

  • Page 1 Brackets (2) Rear Mounting Brackets Brackets (2) Universal Mounting Tubes (4) DS5 Drop Steps PROCEDURE: REMOVE CONTENTS FROM BOX. VERIFY ALL PARTS ARE PRESENT. READ INSTRUCTIONS CAREFULLY. ASSISTANCE IS RECOMMENDED. 1. Start installation on the Passenger/Right front of the of the vehicle. Find the front threaded insert located in between the first pair of holes along the pinch weld, (Figure 1).
  • Page 2 13). Each front channel should have (4) T-bolts, which corresponds to the holes on the DS5 Drop Steps. 8. Attach the DS5 Drop Steps to the Universal Mounting Tube. Each DS5 Drop Step uses (2) 8mm Plate Washers and (4) 8mm Nylon Lock Nuts, (Figure 14—15). Do not tighten hardware. While the hardware is not tightened, the Drop Steps will slide along the length of the channels.
  • Page 3 DS5 RUNNING BOARD 19-22 Wrangler JL 4 Door 10mm Hex Bolt (2) 10mm Flat Washers 10mm Nylon Lock Nut (1) 8mm Hex Bolt (1) 8mm Lock Washer (1) 8mm Flat Washer (Fig 3) Attach Front Support Bracket to the Front Mounting Bracket; Attach Front...
  • Page 4 DS5 RUNNING BOARD 19-22 Wrangler JL 4 Door Rear (Fig 6) Passenger/Right rear mounting location (2) 6mm Hex Bolts (4) 6mm Flat Washers (2) 6mm Nylon Lock Nuts 10mm Hex Bolt (2) 10mm Flat Washers 10mm Nylon Lock Nut (1) 8mm Hex Bolt...
  • Page 5 DS5 RUNNING BOARD 19-22 Wrangler JL 4 Door 10mm Hex Bolt (1) 8mm Hex Bolt (2) 10mm Flat Washers (1) 8mm Lock Washer 10mm Nylon Lock Nut (1) 8mm Flat Washer (Fig 10) Attach Center & Rear Support Bracket to the Rear Mounting Bracket;...
  • Page 6 DS5 RUNNING BOARD 19-22 Wrangler JL 4 Door Front Channels (Fig 13) Insert T-bolts into the Front channels on the universal mounting tube. (Fig 14) Attach the Drop Steps to the front (2) 8mm Nylon Lock Nuts channels of the Universal Mounting Tube.
  • Page 7 DS5 RUNNING BOARD 19-22 Wrangler JL 4 Door (2) 8mm Flat Washers (2) 8mm Lock Washers (2) 8mm Hex Nuts (Fig 17) Attach the Universal Mounting Tube to the Front Mounting Brackets. (Fig 18) Universal Mounting Tube attached to the Front Mounting Bracket.
  • Page 8 DS5 RUNNING BOARD 19-22 Wrangler JL 4 Door (2) 8mm Flat Washers (2) 8mm Lock Washers (2) 8mm Hex Nuts (Fig 21) Attach the Universal Mounting Tube to the Rear Mounting Brackets. (Fig 22) Universal Mounting Tube attached to the Rear Mounting Bracket.

Table of Contents