Index - Multitech MultiModem ZBA Series At Commands Reference Manual

1
11-Bit Mode .............................................................. 15
A
Abort Timer S7 ......................................................... 26
Adaptive Answer Result Code Enable %A ............... 14
Answer A .................................................................... 8
Asynchronous Communications Mode &Q ............... 12
Asynchronous Word Length $EB ............................. 15
AT Command Control %DC ..................................... 14
AT commands
$D – DTR Dialing .................................................. 15
$EB – Asynchronous Word Length ....................... 15
$FC – Quick Connect ........................................... 15
$LB – Long Break ................................................. 15
$MB – Modem Baud Rate .................................... 16
$RP – Response Priority ...................................... 16
$SB – Serial Port Baud Rate ................................ 16
%%%ATMTSMODEM – Escape Configuration for
Remote Configuration ....................................... 23
%A – Adaptive Answer Result Code Enable ........ 14
%B – View Numbers in Blacklist ........................... 14
%C – Data Compression Control .......................... 14
%DC – AT Command Control ............................... 14
%DT – Set Command Mode Time ........................ 15
%E – Fallback and Fall Forward Control .............. 15
%H – Direct Connect Enable ................................ 15
%M – Enable Dialing Message ............................... 9
%R – Cisco Configuration .................................... 15
%S – Command Speed Response ....................... 15
&C – DCD Control ................................................ 11
&D – DTR Control ................................................. 11
&E – XON/XOFF Pacing ...................................... 11
&F – Load Factory Settings .................................. 11
&G – V.22bis Guard Tone Control ........................ 11
&K – Flow Control Selection ................................. 12
&L – Leased-Line Operation ................................. 12
&Q – Asynchronous Communications Mode ........ 12
&S – Data Set Ready (DSR) Control .................... 12
&T – V.54 Test ...................................................... 12
&V – Display Current Settings .............................. 12
&W – Store Current Configuration ........................ 12
&Z= – Storing a Dialing Command ....................... 13
+++AT – Escape Sequence .................................. 23
+DCS= – Select V.44 Data Compression ............. 18
+DR= – V.44 Data Compression Reporting .......... 18
+DS44= – V.44 Data Compression ...................... 19
+MS= – Modulation Selection ............................... 20
+PCW= – Call Waiting Enable .............................. 17
+PIG= – PCM Upstream Enable ........................... 17
+PMH= – Modem on Hold Enable ........................ 17
+PMHF – V.92 Modem Hook Flash ...................... 17
+PMHR= – Modem on Hold Initiate ...................... 17
+PMHT= – Modem on Hold Timer ........................ 18
+PQC= – Quick Connect Control .......................... 18
+VCID= – Caller ID Selection ............................... 21
Multi-Tech Systems, Inc. AT Commands for the MT5634 Family of Products (S000272J)
Arrow.com. Arrow.com. Arrow.com. Arrow.com. Arrow.com. Arrow.com. Arrow.com. Arrow.com. Arrow.com. Arrow.com. Arrow.com. Arrow.com. Arrow.com. Arrow.com. Arrow.com. Arrow.com. Arrow.com. Arrow.com. Arrow.com. Arrow.com. Arrow.com. Arrow.com. Arrow.com. Arrow.com. Arrow.com. Arrow.com. Arrow.com. Arrow.com. Arrow.com. Arrow.com. Arrow.com.
Downloaded from Downloaded from Downloaded from Downloaded from Downloaded from Downloaded from Downloaded from Downloaded from Downloaded from Downloaded from Downloaded from Downloaded from Downloaded from Downloaded from Downloaded from Downloaded from Downloaded from Downloaded from Downloaded from Downloaded from Downloaded from Downloaded from Downloaded from Downloaded from Downloaded from Downloaded from Downloaded from Downloaded from Downloaded from Downloaded from Downloaded from

Index

+VDR= – Distinctive Ring Report ......................... 21
+VRID – Caller ID Query ...................................... 21
A – Answer ............................................................. 8
\A – Select Maximum MNP Block Size ................. 13
A/ – Repeat............................................................. 8
AT – Attention Code ............................................... 8
B – Communication Standard Setting ..................... 8
\B – Transmit Break .............................................. 13
-C – Data Calling Tone ......................................... 14
D – Dial ................................................................... 8
DS=n – Dial Stored Telephone Number ................. 9
E – Echo ................................................................. 9
F – Echo Online Data Characters ........................... 9
H – Hook Control .................................................... 9
I – Information Request .......................................... 9
\K – Break Control ................................................ 13
M – Monitor Speaker Mode .................................... 9
\N – Error Correction Mode Selection ................... 13
N – Modulation Handshake .................................. 10
O – Return Online to Data Mode .......................... 10
P – Pulse Dialing .................................................. 10
\Q – Flow Control Selection .................................. 14
Q – Result Codes Enable/Disable ........................ 10
Sr? – Read Register Value ................................... 10
Sr= – Set Register Value ...................................... 10
\T – Inactivity Timer .............................................. 14
T – Tone Dialing ................................................... 10
\V – Protocol Result Code .................................... 14
V – Result Code Form .......................................... 10
W – Result Code Options ..................................... 10
X – Result Code Selection .................................... 11
Z – Modem Reset ................................................. 11
AT Commands Definition ........................................... 4
Attention Code AT ...................................................... 8
Autoanswer S0 ......................................................... 26
B
Backspace Character Setting S5 ............................. 26
Blacklisting %B ......................................................... 14
Break Control \K ....................................................... 13
Busy-Out Timer at End of Call *DW ......................... 25
C
Call Waiting Enable +PCW= .................................... 17
Callback Attempts #CBA .......................................... 22
Callback Delay #CBD ............................................... 22
Callback Enable/Disable #CBS ................................ 23
Callback Failed Attempts Display #CBF? ................. 22
Callback Failed Attempts Reset #CBFR .................. 22
Callback Parity #CBP ............................................... 22
Callback Security commands
#CBA – Callback Attempts ................................... 22
#CBD – Callback delay ......................................... 22
#CBF? – Callback Failed Attempts Display .......... 22
#CBFR – Resetting Failed Attempts ..................... 22
#CBI – Local Inactivity Timer ................................ 22
#CBN= – Store Callback Password ...................... 22
Index
31