Page 1
Last Modified: 20/02/2023 INSTALLATION MANUAL 1800 Series Steam Shower Bath 30 Day Technical Support: Call 01908 317512 and request technical support for aiding your installation. Replacements Parts: Inside of your warranty period visit: https://www.insigniashowers.com, click support and make a warranty claim.
insigniashowers.com Last Modified: 20/02/2023 Contents Thank you for your purchase Fitting the Door Wheels Steam Diffuser Holder Install Tips for assembly Valve/Water Connections Braided Hose QR Code/Link Control Panel Connections Electrical/Pressure/Tool requirements Steam Generator Connections Box contents Roof Lights Screw Pack contents Control Panel Operating Instructions Levelling the Tray Spare Parts List...
Last Modified: 20/02/2023 Thank you for your recent purchase of an Insignia shower. Please read this booklet with great care to ensure you get the best out of your build and have a shower that will last for many years to come! Like everything, in order to obtain a first class product that will serve you well for many years, the effort and correctness put into the assembly will reflect in the quality of your finish.
TIP 4—Sealing When using Insignia’s RubberGum, please ensure the product does not come in contact with your silicone as this will cause the RubberGum to fail and will not adhere as intended. Rubbergum is immediately waterproof and will gain additional strength over time.
insigniashowers.com Last Modified: 20/02/2023 Electrical Requirements Pressure/Water Requirements Tools Required We recommend a BAR pressure between 2.5 and 3.4 BAR. If STEAM VERSION You will require: you have a combi boiler system no problem should be Voltage Rating 220-240AC experienced. If you have a gravity feed older type installation •...
insigniashowers.com Last Modified: 20/02/2023 Whilst the next steps show you how to assemble your shower we want to make sure you have a correct build to ensure you get a trouble free shower. Therefore our advice is to follow the instructions and perform a dry run to ensure you are confident with the build and you understand fully how the unit is assembled. When we use the word “DRY RUN”...
ST19 19mm Screws VERY IMPORTANT Have you got everything? If not please contact the Insignia Support Line on 01908 317 512. Remember NEVER book your tradesman until everything has arrived, been checked and is present. No replacement/missing parts can be obtained free of charge during or after the build. Any claims can only be within the timescale permitted (48...
insigniashowers.com Last Modified: 20/02/2023 Step 1 — Level the Tray Before any build commences, ensure you are installing in a spacious area and level the tub using a spirit level. Twist to adjust.
insigniashowers.com Last Modified: 20/02/2023 Step 2—Applying the RubberGum to the tub Apply RubberGum to raised sections of the tray and remove backing paper.
insigniashowers.com Last Modified: 20/02/2023 Step 3—Installing Side and Back Panels Starting with the side glass panel and backwall panel, hold in place on the tub to make the first “L” and secure in position using the ST10 screws supplied in the screw pack. ST10 x 3 PLEASE NOTE : Do not drill holes into the tub.
Page 12
insigniashowers.com Last Modified: 20/02/2023 Step 4—Installing Side and Back Panels continued Repeat Step 3 for Opposite Side ST10 x 3...
insigniashowers.com Last Modified: 20/02/2023 Step 5—Installing Column Install the centre column using the M20 nut screws, washers and bolts. M20 x 10...
insigniashowers.com Last Modified: 20/02/2023 Step 6—Connecting the Framework Slot the top and bottom rails into the left and right uprights. Secure with the framework securing clips. Wider rail on top Framework securing clips x4 Narrow rail at the bottom...
Page 15
insigniashowers.com Last Modified: 20/02/2023 Step 7—Connecting the Framework continued Slot the outer frame uprights over the left and right rails and screw using ST16 screws. ST16 x 6...
insigniashowers.com Last Modified: 20/02/2023 Step 8—Installing the Front Frame Carefully lift the front frame and place onto the tub ready to be screwed to the left and right side glass. Slot together and secure using the ST16 screws. ST16 x 6...
insigniashowers.com Last Modified: 20/02/2023 Step 9—Installing Front Fixed Glass Part 1: Carefully slide the fixed glass into the front framework. We recommend 2 people to handle the glass.
Page 18
insigniashowers.com Last Modified: 20/02/2023 Step 10—Installing Front Fixed Glass continued Part 2: Secure the fixed glass with the metal upright using the ST18 screws, screw in from the interior. ST18 x 2...
Page 19
insigniashowers.com Last Modified: 20/02/2023 Step 11—Installing Front Fixed Glass continued Repeat Steps 9-10 for Opposite Side Part 1: Repeat on the other side, first sliding the glass into position. Part 2: Secure the fixed glass with the metal upright using the ST18 screws, screwing from the interior.
insigniashowers.com Last Modified: 20/02/2023 Step 12—Installing Fixed Glass Ribbed Seals From the interior of the bath, slot the 12mm seals between the Please note: Seals are designed to be longer than required. Cut excess off after fitting. framework and the glass. TIP! Use the glass seal tool supplied to aid with installation 12mm Seal x 4...
insigniashowers.com Last Modified: 20/02/2023 Step 13—Fitting the Roof Place the roof on top of the framework and screw into place using ST19 screws upwards. Please note you will need to drill into the roof to secure the screws. ST19 x 6 Rear View...
insigniashowers.com Last Modified: 20/02/2023 Step 14—Fitting the Door Handles and Seals Ensure magnetic seals Fit flap facing out of overlap to ensure they the shower meet...
insigniashowers.com Last Modified: 20/02/2023 Step 15—Fitting the Door Wheels Tighten to secure wheels into door runners. DO NOT OVERTIGHTEN Slide cover off Door Step 16 — Installing the Bottom Door Wheels x4 Slide cover off Door Step 17 — Installing the Doors x2 Slide covers on Hang top door wheels into the top rail...
insigniashowers.com Last Modified: 20/02/2023 Step 18—Steam Diffuser Holder Install Place in middle hole first Turn Tri-Jet to tighten Use Allen key to tighten left chrome outlet Use Allen key to tighten right chrome outlet Note: Connect the 500mm insulation steam pipe supplied to the Tri-jet and connect the other end to the pre-...
insigniashowers.com Last Modified: 20/02/2023 Step 19—Valve/Water Connections Monsoon Shower Bath Connection Hand Shower Body Jets 2x Washers located on the back of the valve Cold Water In Hot Water In Water Feed to Steam Generator...
Water Inlet: When installing the water line for the steam generator, there are 2 options available: • Purchase Insignia’s WRAS approved braided hoses—different packs are available for different shower types. • Install a static water line from the shower valve (middle feed) to the steam generator.
3. Do not aim the hand shower directly at the joints of your shower as this does not fall under “normal showering conditions”. However, due to Insignia’s unique design of the shower tray, water will only leak back in to the tray so you won’t get flooded.
Press once to turn on the panel. Simply press again to turn it off. When powering down the 03 will automatically start and last for approximately 10 minutes. After this the screen will power off. To see our tutorial videos for operating Insignia control panel’s, please search for “Insignia Showers” on YouTube and find our “Insignia Control Panel”...
Page 30
insigniashowers.com Last Modified: 20/02/2023 Bluetooth Connectivity and Radio Tuning Instructions Step 2 Step 1 Then simply go on your device and pair To connect a device via up with the shower which should be Bluetooth, press the music shown as “INS”. Once this is complete function button three times you will hear a beep to signify you’re (which looks like a musical note)
insigniashowers.com Last Modified: 20/02/2023 Steam Room & Shower Safety Guide Never leave children unattended in the shower or bath. Never bath children (under 12) using whirlpool function if fitted. Regulate the temperature of water before showering. Never allow children to use the steam function. This function is for ADULTS ONLY. Always be aware of the steam outlet position.
insigniashowers.com Last Modified: 20/02/2023 Steam Room Usage Guide Steam Room Usage Guide To use the steam room, turn the control panel on. (1) To use the steam room, turn the control panel on. (1) Press the steam button (2) and your generator will be fed with water and the heating Press the steam button (2) and your generator will be fed with water and the heating element will begin to heat the water to create steam.
insigniashowers.com Last Modified: 20/02/2023 How to use AMI System (2nd Gen) Your platinum shower is fitted with the latest AMI system (Aromatherapy Modular Infusion) which takes your steam experience to new heights by enjoying fresh, clean, natural fragrance with the AMI Oil Diffuser Steam Guard. Perfectly designed to deliver the maximum amount of aroma in a matter of minutes.
Page 35
insigniashowers.com Last Modified: 20/02/2023 Bathroom Electrical Zones...
insigniashowers.com Last Modified: 20/02/2023 There are 3 bathroom electrical zones that have been distinguished in the IEE wiring guidelines and these are: Zone 0 is the area inside a bath, basin or shower. It's characterised as 'any area within a bathroom that can hold water'. Any fitting or electrical appliance utilised inside zone 0 must be a maximum of 12 volts (SELV) and completely secured against both partial and total submersion in water (minimum of IPX7) Zone 1 is the region straight above zone 0 to the height of 2.25m from the base of the bath or shower.
(EEE) have to fulfil certain obligations. Under the WEEE directive Insignia is considered the producer of certain products we supply and in line with the demands of the legislation we are pleased to offer the op- portunity to return these products to us for treatment and recycling.
Page 38
insigniashowers.com Last Modified: 20/02/2023...