The Nv-Lrc1 Remote Control; Nv-Mi1 Mute Interface Adapter - Nuvo NV-LRC1 Installation Manual

XII. The NV-LRC1 IR Remote Control
The Essentia System comes with the NV-LRC1 Learning Remote Control. This remote allows wireless control of all keypad functions, as
well as the functions of the audio source equipment. Each NuVo zone keypad has an IR receiver that captures the specific source
commands from any remote control and in turn sends the command ultimately to the appropriate source equipment. Embedded IR code
libraries makes use of the LRC1 with a large variety of audio and video equipment easy. For complete setup and functionality refer to the
User Guide included with the remote control. Additional remote controls are available from NuVo.
XIII. NV-MI1 Mute Interface Adapter
The Mute Interface is used in conjunction with System Mute input in the back of the Essentia amplifier. It acts as a relay for a voltage
from up to two phone lines and two doorbell transformers. When a voltage is presented to the MI1 it then sends a contact closure to the
Essentia System, which in turn causes the system to mute momentarily. This is useful in allowing the telephone ring or doorbell to be
heard when audio is playing in any of the zones, Fig. 17.
Fig. 17
VARIABLE VARIABLE
OUTPUT OUTPUT
OUTPUT POWER
TIP=L TIP=L
20W/6OHM X2
RING=R RING=R
FIXED
FIXED
OUTPUT OUTPUT
ZONE 1 ZONE 2
1 2 3 4 5 6
L L L
R R R
1 2 3 4 5 6
SOURCE INPUTS
The MI1 connects to the NuVo amplifier using a standard
mono patch cable with a mini-plug on each end. Plug one
end into the EXT. MUTE input on the back of the
amplifier and the other end into the input on the front of
the Mi1.
VARIABLE VARIABLE
OUTPUT OUTPUT
OUTPUT POWER OUTPUT POWER
OUTPUT POWER
TIP=L 20W/6OHM X2 TIP=L 20W/6OHM X2
20W/6OHM X2
RING=R RING=R
FIXED FIXED
OUTPUT OUTPUT
ZONE 3 ZONE 4
1
CONNECT TO
NV-E6DX
USE NV-SLC1
CABLE
2
SOURCE LINK ZONE TRIGGER OUTPUTS
MUTE INTERFACE
ADAPTER
NV-MI1
CONNECT TO
MUTE INPUT
VARIABLE VARIABLE
OUTPUT OUTPUT
OUTPUT POWER
OUTPUT POWER
TIP=L TIP=L
20W/6OHM X2
20W/6OHM X2
RING=R RING=R
FIXED FIXED
OUTPUT OUTPUT
ZONE 5 ZONE 6 ZONE 6
5
3 1 3 5 SUM1 SYS ON
CONNECT TO
NV-E6DEZP
USE NV-NC1
CABLE
4 6 2 4 6 SUM2
EXT. MUTE
EMITTER OUTPUTS SYSTEM
NETWORK
The back of the MI1 will accept up to two AC or
DC voltages from two different doorbell chimes.
This connection is done with a two conductor
wire from the terminals on the doorbell chime to
the Doorbell A or Doorbell B inputs on the back
of the MI1. Polarity is not important for this
connection.
A
DOORBELL 1
B
A
DOORBELL 2
B
Connect to Telephone RJ-11
Line 1: Pins 3,4 Line 2: Pins 2,5
Model NV-MI1
Mute Interface Module
Up to two phone lines can be brought into
the RJ-11 connection on the back of the MI1.
The voltage from the phone ringer will
trigger the NuVo System to mute.
16
RS-232
PROGRAM USE CNLY WITH 250V FUSE
MODEL NV-6DM
CONNECT TO
SIX SOURCE SIX ZONE
AUDIO DISTRIBUTION SYSTEM
NV-E6DX
120V 60Hz 500W FUSE:T5 A
USE NV-SLC1 NuVo Technologies Cincinnati Ohio USA
www.nuvotechnologies.com
CABLE
CONFORMS TO
R
UL STD.6500
C US CERTIFIED TO
DIGITAL LINK CAN/CSA STD.E60065
3033118