Connecting The Ez Port To The Essentia Amplifier; Attaching Audio Source Equipment To The Essentia Amplifier; Connecting The Ir Emitters - Nuvo NV-LRC1 Installation Manual

V. Connecting the EZ Port to the Essentia amplifier
When the EZ Port is installed in the wall the only part visible
should be the faceplate, speaker connections for zones 1-6, and
a single RJ45 jack. The speaker connections are made using the
supplied Euro connectors and the supplied pre-terminated
network cable is used to integrate the system keypads. Speaker
connections and the network connection are made from the face
of the EZ Port the back of the Essentia, fig. 4. Any CAT5 cable
terminated using 568A or 568B network wiring will suffice should
you need a longer network connection.
VI. Attaching Audio Source Equipment to the Essentia Amplifier
Each piece of audio source equipment is connected to the
Essentia amplifier with standard stereo RCA cables. Attach the
RCA cable to the corresponding audio output on the source
equipment and to the desired source input on the back of the
Essentia amplifier, Fig. 5.
VII. Connecting the IR Emitters
IR commands for the source equipment are transferred from the
Essentia amplifier to the source equipment via mini IR mouse
emitters. Six of these are supplied with your Essentia System.
The emitter is plugged into the corresponding source IR output
on the Essentia and then placed over the IR receiver window on
the source component, fig. 6. The IR outputs are individually
routed to sources 1-6 allowing IR commands from the chosen
source to only control that source.
The two SUM outputs will flash any IR command that is sent from
any of the zones. This is used to connect the NuVo T2 Tuner,
which has a single IR direct input to control both tuners to the
Essentia System or an IR blaster designed to flash IR commands
to a variety of components. This is done by plugging a single
mono 1/8" patch cable into the SUM IR output and into the Direct
IR input.
Fig. 4
EZ Port (front)
CONNECT TO AMPLIFIER
ZONE 1 ZONE 2 ZONE 3
LEFT RIGHT LEFT RIGHT LEFT RIGHT
_ _ _ _ _
+ + + + +
_ _ _ _ _ _ _ _ _ _
+ + + + + + + + + +
LEFT RIGHT LEFT RIGHT LEFT RIGHT
ZONE 4 ZONE 5 ZONE 6
Essentia EZ Port
Model NV-E6DEZP-UK
Fig. 5
Fig. 6
10
Essentia Speaker
Connection
VARIABLE
OUTPUT
OUTPUT POWER
TIP=L
20W/6OHM X2
RING=R
FIXED
Expander
OUTPUT
_
+
ZONE 1
_ _
+ +
Essentia Network
NuVoNet
Connection
SYS ON
CONNECT TO
NV-E6DEZP
USE NV-NC1
CABLE
EXT. MUTE
SYSTEM NETWORK
VARIABLE VARIABLE
OUTPUT OUTPUT
OUTPUT POWER OUTPUT POWER
TIP=L TIP=L
20W/6OHM X2 20W/6OHM X2
RING=R RING=R
FIXED FIXED
OUTPUT OUTPUT
ZONE 1 ZONE 1 ZONE 2 ZONE 2
6
1 2 3 4 5
CONNECT TO
USE NV-SLC1
1 2 3 4 5 6
SOURCE INPUTS SOURCE LINK
Source 1
Audio
Tuner 1
Out
VARIABLE
OUTPUT
OUTPUT POWER
TIP=L
20W/6OHM X2
RING=R
FIXED
OUTPUT
ZONE 2
PROGRAM
CONNECT TO
NV-E6DX
USE NV-SLC1
CABLE
DIGITAL LINK
VARIABLE
OUTPUT
OUTPUT POWER
TIP=L
20W/6OHM X2
RING=R
FIXED
OUTPUT
ZONE 3 ZONE 3
NV-E6DX
CABLE