Roland V-Drums TD-02KV Setup Manual

Setup Guide
TD-02KV
Check the included items
As soon as you open the package, check to see that all items are included. If anything is missing, please contact your dealer.
1
5
1 2 3 4 6 7
Assemble the drum stand
2
* If you will be using this drum stand for an extended period of time in the same location, we recommend that you use a drum mat (TDM series) made by Roland
to prevent the rubber feet from soiling the surface on which they are placed.
* The drum stand assembly procedure is for right-handed players. If you want to set up the stand for left-handed players, refer to "Assembly for left-handed
players" in the lower right.
Assembling the left and right arm sections
1.
Left arm Left arm
Right arm Right arm
* Lay the left and right arm sections on the floor while assembling them.
Left arm section
1–1.
Use the drum key to loosen the bolt of the left leg
4
holder, and insert the left arm .
3
Drum
key
Left arm
3
Left
4
leg
1–2.
Once the pipe is fully inserted, firmly tighten the bolt
with the drum key.
* Insert the left arm so that the bolt on the holder faces towards
3
the player, as shown in the illustration.
Left arm 3
Bolt
Right arm section
1–3.
Use the drum key to loosen the bolt of the right leg ,
7
and insert the right arm .
6
1–4.
Once the pipe is fully inserted, firmly tighten the bolts (2)
with the drum key.
Right arm 6
Bolt
Right
7
leg
Attach the parts
3
NOTE
* Adjust the position and height of the pads and
Be careful not to get your fingers pinched by the movable parts when you operate the drum
pedals according to your build and preferences,
sound module holder, the hi-hat control pedal, the kick pedal or the cymbals. If using this in
so that they are easy to play.
a location where children are present, be sure to provide adult supervision or guidance.
Attaching the hi-hat (CY-5)
Cymbal nut
"Roland" logo on the
Rotation
farther side
stopper
(convex
portion)
1.
Insert the cymbal so that the stopper (convex portion) on the hi-hat
rod fits into the concave part on the bottom of the cymbal.
2.
Tighten the cymbal nut enough to prevent the pad from wobbling
when you strike it.
Attaching the drum sound module (TD-02)
1.
Use the bolt for the drum sound module holder to attach the drum
sound module to the holder.
Drum sound module holder
Bolt
2.
Loosen the bolt of the drum sound module holder, attach the top part of the
left leg holder and tighten the bolt.
Adjusting the position of the cymbal
Not OK
Adjust the height of the Attach the cymbal
OK
rod so that the highest rods so that they
point of the cymbal is less face straight up, to
than 1.2 meters. prevent the drum
1.2 m
stand from falling
over.
Drum stand
No. Name Quantity
8
Cymbal rod 2
1
Hi-hat rod 1
2
Left arm 1
3
9
Left leg
1
4
Center frame 1
5
Right arm 1
10 6
Right leg 1
7
U-shaped pipe 3
8
12
11
Snare pipe 1
9
U-shaped pipe holder 3
10
13
Snare holder 1
11
Cymbal rod holder
2
12
14
Cable clip 4
13
Cable tie 2
14
Attaching the left/right arm sections onto the
2.
center frame
Center Center
frame frame
Left arm Left arm
Right arm Right arm
2–1.
Use the drum key to loosen bolt of holder A attached
to the left-side pipe (with two holders) on the left side
of the center frame , and insert the left arm of the
5 3
assembly you created in step 1 into holder A.
Center frame 5
Bolt
Left arm 3
Holder A
2–2.
Once the pipe is fully inserted, firmly tighten the bolt
with the drum key.
Bolt
2–3.
Use the drum key to loosen bolt of holder B, and insert
the right arm of the assembly you created in step 1
6
into holder B of the center frame .
5
Bolt
Holder B
Right arm 6
2–4.
Once the pipe is fully inserted, firmly tighten the bolt
with the drum key.
Bolt
Attaching the crash cymbal/ride cymbal (CY-5)
Insert the cymbal onto the top of the cymbal mount.
CY-5 CY-5
CY-5 CY-5
PD-4 PD-4
PD-4 PD-4
CY-5 CY-5
TD-02 TD-02
PDX-8 PDX-8
Hi-hat control Hi-hat control
pedal pedal
Kick pedal Kick pedal
Attaching the toms (PD-4)
Attaching the snare drum (PDX-8)
Tighten
Loosen
Snare holder
U-shaped
pipe
* When attaching the PDX-8 (snare), refer to "About
the memory clamp" on the other side.
* To prevent the drum stand from
tipping over, do not position the
stand leg pipes at the two ends
more than 1.2 meters apart.
OK Not
OK
Before using this unit, carefully read "USING THE UNIT SAFELY" and "IMPORTANT NOTES" (in the leaflet "USING THE UNIT SAFELY" and in the TD-02KV Setup Guide). After reading, keep the document(s)
where it will be available for immediate reference.
Drum sound module, pads, other items
* See "Hi-hat control pedal, kick pedal" on the back
side for how to distinguish between the pedals.
 Cymbal pad for hi-hat/ride/crash
 Hi-hat control pedal  Kick pedal (KT-1)
(CY-5 x 3)
(FD-1)
 Drum sound  Drum sound  Dedicated
module holder module connection cable
(TD-02)
NOTE
• Be careful not to get your fingers pinched between the drum stand and the movable parts when you set up or adjust the drum stand.
If using this in a location where children are present, be sure to provide adult supervision or guidance.
• Be sure that there is plenty of space to safely assemble this instrument.
• Do not use a power tool (e.g., an electric screwdriver) to assemble this instrument. Doing so may damage the screws.
• Do not overtighten the bolts.
• Be careful not to get grease from the bolts on your hands or other items.
Attaching the snare pipe
3.
Snare pipe Snare pipe
3–1.
Use the drum key to loosen the bolt of holder C, and
insert the snare pipe into holder C of the center frame
9
.
5
3–2.
Once the pipe is fully inserted, firmly tighten the bolt
with the drum key.
* Insert the snare pipe that's not fitted with a cap into holder C.
Bolt
Cap
Snare pipe
9 Holder C
Adjusting the vertical pipes
4.
4–1.
Place the center frame upright, then loosen the hand
5
knobs (2) of holders A and B. Next, spread open the
pipes at left and right.
4–2.
Adjust the angle so that the drum stand can stand
up by itself, and then tighten the hand knobs
(2) that you loosened.
4–3.
Make sure that the four vertical pipes remain fully
upright, and that the left/right arms are fully horizontal.
If the stand is wobbling, loosen the bolts for the left leg 4 and
right leg 7 holders and adjust the height. After adjusting the
height, tighten the bolts on the holders.
Hand knobs of
holders A and B
Holder bolts
Connect the pads to the drum sound module (TD-02)
4
Connection procedure
1.
Connect the dedicated
connection cable to the drum
sound module as shown in the
illustration below.
Insert the connector all the
way, then turn the knobs to
lock it in place.
PD-4 PD-4
Knob
For a left-handed setup
Assemble the drum stand as described in
"Assembly for left-handed players" in the "
Assemble the drum stand" section, and then
attach the parts and connect the cables as
shown in the illustration at right.
Bolt
Drum
key
1.2 m
This completes assembly and connections.
 Pad for tom  V-Pad for snare
(PD-4 x 3) (PDX-8)
 AC adaptor
 Drum key
Attaching the pad mounts
5.
Center frame/snare pipe
5–1.
Attach the U-shaped pipe holders onto the top of the
5
center frame , and tighten the respective hand knobs.
10
U-shaped pipe holder 10
Hand knobs
5–2.
Attach the U-shaped pipes onto the U-shaped pipe
8
holders , and firmly tighten the respective hand
10
knobs.
U-shaped pipes 8
Hand knobs
Bolt
Drum
key
5–3.
Attach the snare holder to the snare pipe , and
11 9
tighten the hand knob.
NOTE
The tip of the snare holder is sharp. Handle it with care.
Snare holder 11
Hand knob
Right arm
5–4.
Attach the U-shaped pipe holder to the right leg
10 7
and tighten the hand knob.
Hand knob
10
U-shaped pipe holder
5–5.
Attach the U-shaped pipe onto the U-shaped pipe
8
holder , and use the drum key to firmly tighten the
10
bolt.
U-shaped pipe 8
10
U-shaped pipe holder
Bolt
Cabling diagram for the dedicated connection cable
(as seen from the back)
RD
2.
Labels indicating the pad to be
connected are attached to the
T2
dedicated connection cable.
Connect the cables by referring
to the illustration at right.
T3
CR2
* Insert the plug firmly,
making sure it's all the
KIK
way in.
Label * Fasten the cables so that they will not obstruct your playing; use cable clips
We recommend attaching the clips in the locations shown with a
Make sure to wrap the cable ties around the pipes.
2
( ( RD RD) ) (CR1) (CR1)
CY-5 CY-5 CY-5 CY-5
( ( T1 T1) )
(T2) (T2)
( ( HH HH) )
PD-4 PD-4 PD-4 PD-4
CY-5 CY-5
TD-02 TD-02
( ( T3 T3) ) ( ( SNR SNR) )
PD-4 PD-4 PDX-8 PDX-8
Hi-hat Hi-hat
control control
pedal pedal
Kick pedal Kick pedal
à When you've finished making connections, turn on the power as
described in " Quick Start", and verify that you can hear sound.
© 2022 Roland Corporation
Accessing the Accessing the TD-02 TD-02 Accessing the Accessing the
Owner's Manual Owner's Manual video manual video manual
Refer to the "Owner's You can scan the
Manual" (Roland website) following 2D code to see
for details on how to use a quick start video. This
TD-02. Use this 2D code video explains the steps
to access the website. for assembly.
Attaching the tom pads (T1, T2), cymbal rod
6.
and hi-hat rod
6–1.
Attach the toms (2) onto the U-shaped pipe on the
8
top of the center frame .
5
Bolt
T1 T1 T2 T2
Drum
U-shaped
key
pipe
8
6–2.
Attach the cymbal rod holders (2) onto the U-shaped
12
pipes on the top of the center frame .
8 5
6–3.
Insert the rods into the holders, and adjust the position
and direction of all parts as shown in the illustration to
complete the setup.
Cymbal rod 1
2
Hi-hat rod
Assembly for left-handed players
If you want to use a left-handed setup, assemble the stand as follows.
• Detach holder C (for the snare) that's on the left side of the center
frame 5 , and attach it onto the right side. Attach the snare pipe 9
onto holder C, and then attach the snare holder 11 .
• Swap the positions of the left arm and left leg with the right arm
3 4
and right leg . Attach the arm so that the hi-hat rod holder bolt
6 7
faces inwards (towards the player), and then attach the hi-hat rod 2 .
• Attach the U-shaped pipe holder 10 and U-shaped pipe 8 on the
left-side leg.
Hi-hat rod Hi-hat rod
9
U-shaped U-shaped
pipe pipe
8
Snare pipe Snare pipe
9
Left leg Left leg
Right leg Right leg
4
7
CR1
HH
T1
TD-02
SNR
"CR2" is not used. You can use a
separately sold cymbal set (OP-
TD1C) to add more cymbals. If
you are not adding this, leave
the cap attached. Fasten it so
that it does not obstruct your
HHC
performance.
and cable ties .
13 14
.
Cabling diagram for the dedicated
connection cable
(As seen from the back)
CR1 RD
HH
T1 T2
TD-02
SNR
T3
CR2
KIK
HHC
"CR2" is not used. You can use a separately sold
cymbal set (OP-TD1C) to add more cymbals. If you
are not adding this, leave the cap attached. Fasten
it so that it does not obstruct your performance.