Related Manuals for GTE ADICOS M-BUSMASTER S
Summary of Contents for GTE ADICOS M-BUSMASTER S
- Page 1 M-BUSMASTER S IP20 Operating Manual M-BUSMASTER S GTE Industrieelektronik GmbH | Helmholtzstr. 21, 38–40 41747 Viersen | Germany | +49 2162 3703-0 | info@gte.de...
- Page 2 41747 Viersen GERMANY Support hotline: +49 2162 3703-0 E-Mail: support.adicos@gte.de © 2023 GTE Industrieelektronik GmbH – This document and all figures contained may not be copied, changed, or distributed without explicit approval by the manufacturer! Subject to technical changes! ADICOS and GSME are registered trademarks of GTE Industrieelektronik GmbH.
- Page 3 The ADICOS M-BUSMASTER S is a level converter and serves as the interface between the ADICOS Service Software and the M-Bus system. Up to 20 ADICOS detectors can be connect- ed to the M-Bus output.
-
Page 4: Table Of Contents
Primary Cable Shield ..........23 420-2410-002 EN12 ADICOS M-BUSMASTER S... -
Page 5: About This Manual
Objective This manual describes how to properly attach, wire, start up and operate the ADICOS M-BUSMASTER S. Once the device has been successfully started up, this document serves as a reference in the event of malfunctions. It is intended to be used only by properly qualified personnel (–› chap. 2, For Your Safety). -
Page 6: Abbreviations
M-BM ADICOS M-BUSMASTER ADICOS power supply unit NT V40-A3 ADICOS fire detection system Storing this Manual Store this manual near the equipment, in a place where it can easily be accessed when needed for reference. 420-2410-002 EN12 ADICOS M-BUSMASTER S... -
Page 7: Safety Instructions
• Read the entire manual and follow the instructions! Intended Use The ADICOS M-BUSMASTER S is a communication interface used to operate ADICOS detec- tors that detect fire in industrial environments. It also serves as the interface to a service-PC with the ADICOS service software. -
Page 8: Personnel Qualification
• Original spare parts and accessories may only be installed by trained spe- cialist personnel. • Qualified personnel are persons as described in Chap. 2.3. Scope of Delivery The following components are included in delivery of the ADICOS M-BUSMASTER S: Quantity Description ADICOS M-BUSMASTER S... -
Page 9: Design
DESIGN Design Overview Description Enclosure End panel, field supply side Status lEDs Plug-in terminals for ADICOS M-Bus and power supply Top hat rail (optional) End panel, interface side (back) ADICOS M-BUSMASTER S 420-2410-002 EN12... -
Page 10: Connections
DESIGN Connections 4.2.1 Field Supply Side Terminal “Power out” (plug-in) +40V DC +40 V +24V DC +24 V Terminal “M-Bus out” (plug-in) ADICOS M-Bus A ADICOS M-Bus B ADICOS M-Bus A ADICOS M-Bus B 420-2410-002 EN12 ADICOS M-BUSMASTER S... - Page 11 On the respective models, the (mini) USB socket is in the middle of the interface side of the device, above the power supply con- nections. Drivers and notes on installation can be found on the included data medium! ADICOS M-BUSMASTER S 420-2410-002 EN12...
-
Page 12: Display Elements
Display Elements Status LEDs The status lEDs of the ADICOS M-BUSMASTER S are located in the middle of the end panel on the field supply side. They indicate the following (from top to bottom): 40 V bus voltage okay... -
Page 13: Installation
INSTAllATION Installation The ADICOS M-BUSMASTER S is a tabletop device that is intended to be used indoors. With the option top hat rail bracket, it can be mounted on a top hat rail in an electrical cabinet. If the device is operated as a tabletop unit, the included self-adhesive feet should by stuck to the bottom of the enclosure. - Page 14 Connecting service PC Depending on the device model, connect the interface cable to the service PC. ► When using the model “Ethernet,” connect the network cable to the service PC through the respective network infrastructure. 420-2410-002 EN12 ADICOS M-BUSMASTER S...
-
Page 15: Comissioning
The customer has to have a service PC with ADICOS System Software installed. A serial RS-232 / USB interface is standard on the ADICOS M-BUSMASTER S. Connect the ADICOS M-BUSMASTER S to the COM port on the service PC and start the GSME central software. - Page 16 (reply) as well as the yellow lED (query) should be flashing. 6.3.2 Integrating M-BUSMASTER S via LAN Connection / Ethernet The ADICOS M-BUSMASTER S can be equipped with an Ethernet connection upon request. The network card is based on a module XPort supplied by lantronix. Fig. 9 The Ethernet module automatically obtains its IP address from the DHCP server of the net- work.
- Page 17 Changing IP Address Select the device to be changed from the list. Then click “Assign IP.” The wizard used to adapt the IP address opens. Fig. 11 Select “Assign a specific IP address“ and click “Next.” ADICOS M-BUSMASTER S 420-2410-002 EN12...
- Page 18 COMISSIONING Fig. 12 Enter the desired IP address and the subnet mask, then click “Next.” Fig. 13 Click “Assign.” The new IP address is programmed. Fig. 14 Click “Finish” and close the Device Installer. 420-2410-002 EN12 ADICOS M-BUSMASTER S...
-
Page 19: Checking Bus Communication
The software enables each separate device to be integrated and checked using the central computer. While the service PC is communicating with the connected detectors, the green lED (reply) as well as the yellow lED (query) should be flashing. ADICOS M-BUSMASTER S 420-2410-002 EN12... -
Page 20: Operation
OPERATION Operation The ADICOS M-BUSMASTER S does not have a switch. It is started up by connecting the included external plug-in power supply to the 230 V supply or by connecting it to a DC 24V power supply. The top red status lED is illuminated during operation. -
Page 21: Technical Data
Mounting environment Free of vibrations Degree of protection IP20 Communication properties Protocol (field supply side) ADICOS M-Bus Maximum number of detectors Interface model RS-232 4800 baud Interface model USB 2.0 standard Interface model Ethernet 100 MBit ADICOS M-BUSMASTER S 420-2410-002 EN12... -
Page 22: Id Plate
Model: Device model SERIAl: Serial number Year of production (variable) (variable) ART-Nr: Article number TEMP: Ambient Degree of (variable) temperature protection VAR: Interface /VA: Voltage range / Input fuse maximum pow- er consumption CE marking 420-2410-002 EN12 ADICOS M-BUSMASTER S... -
Page 23: Annex
+24 V primary cable primary cable X7 (Stoer) X7 (Stoer) X6aus (Al) X6aus (Al) X6ein (Al) X6ein (Al) LOOP B LOOP B LOOP A LOOP A M-Bus A M-Bus A M-Bus B M-Bus B +24 V ADICOS M-BUSMASTER S 420-2410-002 EN12...