Table Iii - Komatsu 730E Operation & Maintenance Manual

Introduction - Section 1
Page 1-10
Standard Assembly Torques For 12-Point, Grade 9,
Capscrews (SAE)
The following specifications apply to required assembly
torques for all 12-Point, Grade 9 (170,000 psi minimum
tensile), Capscrews.
Capscrew threads and seats SHALL be lubricated
•
when assembled.
Unless instructions specifically recommend otherwise,
these standard torque values are to be used with
simple lithium base chassis grease (multi-purpose EP
NLGI) or a rust- preventive grease (see list, this page)
on the threads.
Torques are calculated to give a clamping force of
•
approximately 75% of proof load.
The maximum torque tolerance shall be ±10% of
•
the torque value shown.
TABLE II. - STANDARD ASSEMBLY TORQUE
for 12-Point, Grade 9 Capscrews
CAPSCREW TORQUE
SIZE* ft. lbs.
0.250 - 20
0.312 - 18
0.375 - 16
0.438 -14
0.500 -13
0.562 - 12
0.625 - 11
0.750 - 10
0.875 - 9
1.000 - 8
1.000 - 12
1.125 - 7 1230
1.125 - 12 1330
1.250 - 7 1715
1.250 - 12 1840
1.375 - 6 2270
1.375 - 12 2475
1.500 - 6 2980
1.500 - 12 3225
* Shank Diameter (in.) - Threads per inch
This table represents standard values only. Do not use these val-
ues to replace torque values which are specified in assembly
instructions.
TORQUE TORQUE
N.m kg.m
12 16 1.7
24 33 3.3
42 57 5.8
70 95 9.7
105 142 14.5
150 203 20.7
205 278 28.3
360 488 49.7
575 780 79.4
860 1166 119
915 1240 126
1670 170
1800 184
2325 237
2495 254
3080 313
3355 342
4040 411
4375 445
Standard Charts and Tables
Standard Metric Assembly Torque For Class 10.9
Capscrews & Class 10 Nuts
The following specifications apply to required assembly
torques for all metric Class 10.9 finished hexagon head
capscrews and Class 10 nuts.
Capscrew threads and seats SHALL NOT be lubri-
•
cated when assembled. These specifications are
based on all capscrews, nuts, and hardened
washers being phosphate and oil coated.
NOTE: If zinc-plated hardware is used, each piece
must be lubricated with a Rust Preventive Grease or
Lithium-base grease to achieve the same clamping
forces provided below.
Torques are calculated to give a clamping force of
•
approximately 75% of proof load.
The maximum torque tolerance shall be within
•
±10% of the torque value shown.
TABLE III. - STANDARD METRIC ASSEMBLY TORQUE
CAPSCREW TORQUE
SIZE* N.m
M6 x1 12
M8 x 1.25 30
M10 x 1.5 55
M12 x 1.75 95
M14 x 2 155
M16 x 2 240
M20 x 2.25 465
M24 x 3 800
M30 x 3.5 1600
M36 x 4 2750
* Shank Diameter (mm) - Threads per millimeter
This table represents standard values only. Do not use these val-
ues to replace torque values which are specified in assembly
instructions.
Suggested* Sources for Rust Preventive Grease:
AMERICAN ANTI-RUST GREASE #3-X from
•
Standard Oil Company (also American Oil Co.)
GULF NORUST #3 from Gulf Oil Company.
•
MOBILARMA 355, Product No. 66705 from Mobil
•
Oil Corporation.
RUST BAN 326 from Humble Oil Company.
•
RUSTOLENE B GREASE from Sinclair Oil Co.
•
RUST PREVENTIVE GREASE - CODE 312 from
•
the Southwest Grease and Oil Company.
NOTE: This list represents the current Engineering
approved sources for use in Komatsu manufacture. It is
not exclusive. Other products may meet the same
specifications of this list.
OM1032.2
TORQUE TORQUE
ft.lbs. kg.m
9 1.22
22 3.06
40 5.61
70 9.69
114 15.81
177 24.48
343 47.43
590 81.6
1180 163.2
2028 280.5