Related Manuals for Bosch BAT 690 UK
Summary of Contents for Bosch BAT 690 UK
- Page 1 BAT 690 UK Battery Charger en Original instructions Charger for 12 volt and 24 volt batteries...
- Page 2 | 2 | BAT 690 | 1 689 981 234 2021-05-01 Robert Bosch GmbH...
-
Page 3: Table Of Contents
Decommissioning Device description Temporary shutdown 4.3.1 Selection buttons Change of location 4.3.2 Status LEDs Disposal and scrapping Initial startup Technical Data Connecting charging cables to the BAT 690 Install the wall mounting Robert Bosch GmbH 1 689 981 234 2021-05-01... -
Page 4: Symbols Used
When a Bosch product is handed over to another person, not only the operating instructions but also the safety instructions and information on its designated use must be handed over to the person. -
Page 5: User Group
Whatever the event, imminent danger exists, also ensure that the electrical Bosch liability is restricted to the amount for which the equipment or the electrical operating material is not customer actually pays for this product. This disclaimer used. -
Page 6: Safety Instructions
High-voltage components must never exhibit signs of external damage. The insulation of the high-voltage wiring must be intact and undamaged. Watch out for any abnormal deformation of the high-voltage wiring. 1 689 981 234 2021-05-01 Robert Bosch GmbH... -
Page 7: Danger Of Acid Burning
¶ Route cables at a suitable distance from rotating parts. ¶ Transport and operate the equipment only in accordance with the operating instructions. Robert Bosch GmbH 1 689 981 234 2021-05-01... -
Page 8: Product Description
5 Selection keys 6 TFT display 7 Red LED for "Mains on", "Incorrect polarity", "Fault or overload" 8 Green LED for "charging operation" 9 Yellow LED for "Back-up mode" and "Buffer mode" 1 689 981 234 2021-05-01 Robert Bosch GmbH... -
Page 9: Initial Startup
Connecting and charging ¶ Voltage must be supplied to the BAT 690 via a grounded mains voltage system. ¶ Only use of the charging cables supplied by Bosch. ¶ The power supply cable and charging cables must 4510026-08_Ko be in perfect condition. -
Page 10: Switching On
Time out If the message " " is displayed, a charging phase could not be completed. This indicates that either the parameter was entered incorrectly, or that the battery is defective. 1 689 981 234 2021-05-01 Robert Bosch GmbH... - Page 11 (wheelchairs, sweepers, ...), at least every 3rd 8. Press charging process should take the form of full The "Capacity" menu is displayed. charging to maintain the battery capacity as long as possible. Robert Bosch GmbH 1 689 981 234 2021-05-01...
-
Page 12: Buffer Mode
7. Back-up mode is stopped with The yellow LED is off. The "Mode" menu is displayed. 8. Switch off the BAT 690 on completion of back-up mode. 9. Remove the charging clips from the battery. 1 689 981 234 2021-05-01 Robert Bosch GmbH... -
Page 13: Configuration
The parameter set is displayed. displayed when charging the battery. 1. Select charging cable length with 2. Press " The selected charging cable length is used when charging. The charging cables are not to be modified. Robert Bosch GmbH 1 689 981 234 2021-05-01... -
Page 14: Language
BAT 690 and allow it to cool down. 3. Press Insufficient temperature in the BAT 690, warm up BAT 690. The "Configuration" menu is displayed. In case of any other malfunctions or fault numbers, inform customer service. 1 689 981 234 2021-05-01 Robert Bosch GmbH... -
Page 15: Maintenance
(EN 61140:2002 + A1:2006) Dimensions (W x H x D) 220 x 116 x 473 mm 8.7 x 4.6 x 18.6 inch Workplace-related < 60 dB(A) noise emission value (Lpa) (with fan on) Robert Bosch GmbH 1 689 981 234 2021-05-01... - Page 16 Robert Bosch GmbH Automotive Service Solutions www.boschaftermarket.com Franz-Oechsle-Straße 4 73207 Plochingen DEUTSCHLAND bosch.prueftechnik@bosch.com http://www.downloads.bosch-automotive.com 1 689 981 234 | 2021-05-01...
Need help?
Do you have a question about the BAT 690 UK and is the answer not in the manual?
Questions and answers